Atlantis COM-870E User manual

COM-870E
Wide Range Temperature
COM Express Type 6 CPU Module
User’s Manual
Version 1.0
85
2012.06
85

This page is intentionally left blank.

- I -
Index
Contents
Chapter 1 - Introduction......................................................................1
1.1 Copyright Notice...........................................................................2
1.2 Declaration of Conformity ...........................................................2
1.3 About This User’s Manual ...........................................................4
1.4 Warning .........................................................................................4
1.5 Replacing the Lithium Battery.....................................................4
1.6 Technical Support ........................................................................4
1.7 Warranty ........................................................................................5
1.8 Packing List ..................................................................................6
1.9 Ordering Information....................................................................6
1.10 Specications .............................................................................7
1.11 Board Dimensions ......................................................................8
Chapter 2 - Installation........................................................................9
2.1 What is “COM Express”?...........................................................10
2.2 Block Diagram ...........................................................................12
2.3 Connectors..................................................................................13
2.4 COM Express AB Connector (bottom side) .............................14
2.5 COM Express CD Connector (bottom side) ............................15
2.6 The Installation Paths of CD Driver ..........................................16
2.7 Heatsink Installation...................................................................17
Chapter 3 - BIOS................................................................................19
3.1 BIOS Main Setup.........................................................................20
3.2 Advanced Settings .....................................................................21
3.2.1 ACPI Conguration ........................................................22
3.2.2 CPU Conguration.........................................................23
3.2.3 SATA Conguration .......................................................24
3.2.4 Intel Anti-Theft Technology Conguration ..................25
3.2.5 AMT Conguration.........................................................26
3.2.6 USB Conguration.........................................................28
3.2.7 H/W Monitor....................................................................29
3.2.8 Super IO Conguration .................................................30
3.2.9 Sandybridge PPM Conguration..................................33

- II -
Index
3.3 Chipset ........................................................................................34
3.3.1 System Agent (SA) Conguration ................................35
3.3.2 PCH-IO Conguration....................................................45
3.4 Boot Settings ..............................................................................50
3.5 Security .......................................................................................51
3.6 Save & Exit..................................................................................53
3.7 AMI BIOS Checkpoints...............................................................54
3.7.1 Checkpoint Ranges .......................................................54
3.7.2 Standard Checkpoints...................................................55
Appendix ............................................................................................63
Appendix A: I/O Port Address Map .................................................64
Appendix B: Interrupt Request Lines (IRQ) ...................................67
Appendix C: BIOS Memory Map......................................................68
Appendix D: Digital I/O Setting .......................................................70

- 1 -
Introduction
1Chapter 1
Introduction
Chapter 1 - Introduction

- 2 -
Introduction
1.1 Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
1.2 Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the
directives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of
shielded cables. This kind of cable is available from ARBOR. Please contact
your local supplier for ordering information.
This product has passed the CE test for environmental specications. Test
conditions for passing included the equipment being operated within an
industrial enclosure. In order to protect the product from being damaged by
ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the
use of CE-compliant industrial enclosure products.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:

- 3 -
Introduction
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are in
compliance and conform to the European Union’s Restriction of Use of Haz-
ardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main pur-
pose of the directive is to prohibit the use of lead, mercury, cadmium, hexava-
lent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl
ethers (PBDE) in electrical and electronic products. Member states of the EU
are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not contain
unintentional additions of lead, mercury, hex chrome, PBB or PBDB that ex-
ceed a maximum concentration value of 0.1% by weight or for cadmium exceed
0.01% by weight, per homogenous material. Homogenous material is dened
as a substance or mixture of substances with uniform composition (such as sol-
ders, resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-
96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility to the
earth we live, Arbor hereby conrms all products comply with the restriction
of SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH
--Registration, Evaluation, Authorization, and Restriction of Chemicals)
regulated by the European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- 4 -
Introduction
1.3 About This User’s Manual
This user’s manual provides general information and installation instructions
about the product. This User’s Manual is intended for experienced users and
integrators with hardware knowledge of personal computers. If you are not
sure about any description in this booklet. please consult your vendor before
further handling.
1.4 Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow
the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or cir-
cuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that comes
with the Single Board Computer, whenever components are separated from
the system.
1.5 Replacing the Lithium Battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trash-can. It must be disposed of in
accordance with local regulations concerning special waste.
1.6 Technical Support
If you have any technical difculties, please do not hesitate to call or e-mail our
customer service.
http://www.arbor.com.tw
E-mail:[e-mail]

- 5 -
Introduction
1.7 Warranty
This product is warranted to be in good working order for a period of two years
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of,
or inability to use this product. Vendor will not be liable for any claim made by
any other related party.
Vendors disclaim all other warranties, either expressed or implied, including
but not limited to implied warranties of merchantability and tness for a
particular purpose, with respect to the hardware, the accompanying product’s
manual(s) and written materials, and any accompanying hardware. This limited
warranty gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.

- 6 -
Introduction
1.8 Packing List
1.9 Ordering Information
If any of the above items is damaged or missing, contact your vendor
immediately.
Packing List
Before you begin installing your single board, please make sure that the following
materials have been shipped:
1 x COM-870E COM Express CPU Module
1 x Driver CD
1 x Quick Installation Guide
COM-870E-827E Intel® Celeron 827E WT COM Express CPU
module
HS-65M2-F1 Heat Spreader (95 x 125 x 18mm)
HS-65M2-C1 Cooler (95 x 125 x 34.8mm)
PBE-1702 COM Express Type 6 evaluation board in
ATX form factor
CBK-04-1702-00
Cable kit
1 x SATA cable
2 x COM port cables
1 x USB cable