Atlas 5 Turbo Twister Slide User manual

5 ft. Turbo Twi ter Slide
A embly Manual ver.1

A e m b l y M a n u a l f o r
5 f t T u r b o T w i t e r S l i d e
Page 2
Tools needed for assembly:
1/2” ocket and ocket wrench
1/2” wrench
Optional Tools:
cordle impact drill
ocket adapter
1/2” Ratchet wrench
Electric drill
3/8” drill bit
HARDWARE:
(23) 5/16”x 1-1/2” lag bolt -(1) 14” Turbo Twi ter Chain
(96)5/16” lock nut(217)3/8” wa her(98) 5/16” x 1” bolt
*Secure one end of chain to clo e t bolt on lide to
play tructure. Secure other end of chain to play
tructure with lag bolt and wa her.

A e m b l y M a n u a l f o r
5 f t T u r b o T w i t e r S l i d e
(6)- 45 Degree Elbow (1) Tube Slide Exit
(6)- 45 degree
Elbow Con i t
of (6) Bottom
and (6) Top
Halve .
Parts:
Page 3
(1) - Entry Tube
with Cover Plate

Page 4
•1st elbow- flanges are
horizontal.
•2nd elbow- spin CCW
one bolt hole.
•3rd elbow- spin CCW one
bolt hole.
•4th elbow- spin CCW one
bolt hole.
•5th elbow- spin CCW one
bolt hole.
•6th elbow- spin CCW one
bolt hole.
Install exit so that the sides
are equal and horizontal and
with two holes between the
top of the exit section and
the small rib of the sixth
elbow.

Page 5
A e m b l y Proce
STEP #1- Assemble six elbows. Insert (6) bolts
with washers through holes on overlap side
of joining flanges. Secure bolts with (6)
washers and locknuts on other side of joining
flanges then tighten.
STEP #2- Turn Entry Tube so that it angles to
the right side of opening. Center Entry Tube
in open-ing and make sure bottom of Entry
Tube hole is flush at 5 ft deck level. Secure
Entry Tube with (12) lag bolts with washers
around outside perimeter of cover plate.
Step #3- Position flat flange end of 45 degree
Elbow against overlap end of Entry Tube.
Turn 1st Elbow so that the joining flanges are
horizontal. Secure Elbow section to Entry
Tube with (12) bolts, (24) washers, and (12)
lock-nuts. Start locknuts on bolt threads and
then tighten.

Page 6
Step #4- Po ition 3rd Elbow flange end
again t 2nd Elbow overlap end o large
joining flange line up. Line up rib of 2nd
and 3rd Elbow and then ecure with (12)
bolt , (24) wa h-er , and (12) locknut .
Step #5- Position third elbow with flange end
against second elbow overlap end so large
joining flanges line up. Turn third elbow
counterclockwise one bolt hole and then
secure with (12) bolts, (24) washers, and (12)
locknuts.
A e m b l y P r o c e
Step # 6- Position fourth Elbow with flange
end against third Elbow overlap end so large
joining flanges line up. Turn fourth elbow
counterclockwise one bolt hole and then
secure with (12) bolts, (24) washers, and (12)
locknuts.

Page 7
A e m b l y P r o c e
Step # 7- Position fifth Elbow with flange end,
against fourth Elbow overlap end so large
joining flanges line up. Turn fourth elbow
counterclockwise one bolt holes and then
secure with (12) bolts, (24) washers, and (12)
locknuts.
Step # 8- Position sixth Elbow with flange
end against fifth Elbow overlap end so large
join-ing flanges line up. Turn fourth elbow
coun-terclockwise one bolt holes and then
secure with (12) bolts, (24) washers, and (12)
lock-nuts.
Step #9- Secure over lap end of la t 7th
Elbow Tube to Tube Slide Exit with (2) 5/16”
bolt with wa her . Secure two bolt into
preed nut near the bottom of the Exit
making ure the exit i level at both ide .
Intall 5/16” x 1-1/2” lag bolt with wa her
through remaining
ten hole in elbow flange into platic of the
exit ection, taking care not to overtighten
lag bolt in pla tic.

Page 8
Proper in tallation and afety i the re pon ibility of the in taller.
Plea e contact Atla Molding if any problem occur with the in talla-
tion. [phone]
A e m b l y P r o c e
SAFETY PRECAUTIONS
Assembled 5ft Turbo Twister Slide
For installation the opposite direction of what has been shown, do these steps the opposite that you
would use to assemble this slide (i.e. clockwise as opposed to counterclockwise, begin the entry angled
to the left as opposed to the right).
-
-
-
-
-
Make ure to properly follow in truction
manual for your pecific lide.
Make ure the play tructure that you are
attaching the lide to i turdy and able to
upport thi type of equipment.
Check and make ure all hardware i e-
cured properly. Thi will need to be done a
routine maintenance program on all play-
ground equipment.
Thi product i made to be u ed a a play-
ground lide exclu ively.
If for any rea on in tallation can not be
completed throughly; do not leave lide or
opening on play equipment in a un afe man-
ner to which injurie may occur.