Atlas Turbo Twister Slide User manual

9 ft. Turbo Twister Slide
Assembly Manual

A s s e m b l y M a n u a l f o r
9 f t . T u r b o T w i s t e r S l i d e
Page 2
Tools needed for assembly:
1/2” socket and socket wrench
1/2” wrench
OptionalTools:
cordless impact drill
socket adapter
1/2” atchet wrench
Electric drill
3/8” drill bit
HA DWA E:
(13) 5/16”x 1 1/2” lag bolts -(1) 12” Turbo Twister Support Chain
(120) 5/16” lock nuts(264) 5/16” washers (132) 5/16” x 1” bolts

Parts:
(1) Entry Tube with Cover plate (1) Tube Slide Exit
(5) 90 Degree Elbows
Elbows Consists of (5) Bottom and (5) Top Halves
Page 3
A s s e m b l y M a n u a l f o r
9 f t . T u r b o T w i s t e r S l i d e

Q u i c k e f e r e n c e G u i d e
Page 4

Page 5
Step #3
Position flange end of Elbow against
overlap end of Entry Tube. Turn Elbow
to left so that the joining flanges are
horizontal. Then turn Elbow one bolt
hole counterclockwise. Secure Elbow
section to Entry Tube with (12) bolts,
(24) washers, and (12) locknuts. Start
locknuts on bolt threads and then
tighten with tools.
Asse m b l y P r o c e s s
STEP #1
Assemble five elbows. Insert (12) bolts
with washers through holes on overlap
side of joining flanges. Secure bolts
with (12) washers and locknuts on flange
side of joining flanges then tighten with
tools. Make sure overlaps and flanges
are at same ends on both halves before
assembly.
STEP #2
Turn Entry Tube so that it angles to
the right side of opening. Center Entry
Tube in opening and make sure bottom
of Entry Tube hole is flush at 7 ft deck
level. Secure Entry Tube with (12) lag
bolts with washers around outside
perimeter of cover plate.

Step #4
Position second Elbow flange end against
first Elbow overlap end so large joining
flanges line up. Turn second elbow coun-
terclockwise one bolt hole and then se-
cure with (12) bolts, (24) washers, and
(12) locknuts.
Step #5
Position third Elbow with flange end
against second Elbow overlap end so
large joining flanges line up. Turn third
Elbow counterclockwise two bolt holes
and then secure with (12) bolts, (24)
washers, and (12) locknuts.
Page 6
Step # 6
Position fourth Elbow with flange end,
against third Elbow overlap end so large
joining flanges line up. Turn fourth
elbow counterclockwise two bolt holes
and then secure with (12) bolts, (24)
washers, and (12) locknuts.
Assemb l y P r o c e s s

Step # 7
Position fifth Elbow with flange end,
against fourth Elbow overlap end so
large joining flanges line up. Turn fifth
elbow counterclockwise two bolt holes
and then secure with (12) bolts, (24)
washers, and (12) locknuts.
Step # 9
Secure trimmed over lap end of last
Tube to Tube Slide Exit with two 5/16”
bolts with washers at marked locations.
Make sure bolts are started by hand
first and then tighten. Install ten
5/16” x 1-1/2” lag bolts with washers in
remaining holes, screwing them into the
plastic exit, take care not to over-
tighten.
Page 7
Step # 8
Install Tube Slide Exit section against
trimmed overlap end of fifth Elbow.
Loosen bottom bolts of Elbow on either
side of joining flanges for better hole
alignment. Install tube slide exit against
fifth elbow flange so that sides of Tube
Slide Exit are level with two bolts be-
tween top of exit and small rib on fifth
elbow.
Asse m b l y P r o c e s s

Page 8
Assembled 9ft Turbo Twister Slide
Proper installation and safety is the responsibility of the in-
staller.
Please contact Atlas Molding if any problems occur with the in-
stallation. [phone]
Step # 10
Check to make sure all bolts and lags are
secured tightly on tube slide. Do not
overtighten locknuts and lag bolts. In-
stall Turbo Twister Support Chain from
slide to upright support.
Assemb l y P r o c e s s

- Make sure t pr perly f ll w instructi n manual
f r y ur specific slide.
- Make sure the play structure that y u are attach-
ing the slide t is sturdy and able t supp rt this
type f equipment.
- Check and make sure all hardware is secured
pr perly. This will need t be d ne as r utine
maintenance pr gram n all playgr und equip-
ment.
- This pr duct is made t be used as a play-
gr und slide exclusively.
- If f r any reas n installati n can n t be c m-
pleted thr ughly; d n t leave slide r pening n
play equipment in an unsafe manner t which in-
juries may ccur.
- Please check with CPSC’s rec mmendati n f r
safety n their web site and f ll w their m st re-
cent handb k.
www.cpsc.g v/cpscpub/pubs/324.pdf