Atop SE8502-M12 Series Manual

Introduction
Thank you for choosing the Atop IP68 Rated 2-Port Serial to Ethernet Serial
Device Server. The SE8502-M12 Series provide industrial grade media conver-
sion between Ethernet and RS-232/RS-422/RS-485. This Guide covers four
product models:
■SE8502-M12
IP68 Rated 2-Port RS-232/422/485 to Ethernet Serial Device Server
■SE8502-M12 (DIN-Rail)
IP68 Rated 2-Port RS-232/422/485 to Ethernet Serial Device Server with
DIN-Rail Mounting Kit
■SE8502-Sis-M12
IP68 Rated 2-Port RS-422/485 to Ethernet Serial Device Server, 2KV Isolation on
serial ports
■SE8502-Sis-M12 (DIN-Rail)
IP68 Rated 2-Port RS-422/485 to Ethernet Serial Device Server with DIN-Rail
Mounting Kit, 2KV Isolation on serial ports
Package Check List
Inside the package you will find the following items:
■SE8502-M12 / SE8502-M12 (DIN-Rail) / SE8502-Sis-M12
SE8502-Sis-M12 (DIN-Rail) x 1
■DIN-Rail Kit (only for SE8502-M12 (DIN-Rail) and SE8502-Sis-M12
(DIN-Rail)) x 1
■Hardware Installation Guide (Warranty card is included) x 1
■Product CD (information on the product as well as software) x 1
Note: please contact your sales representative if any of the above mentioned
products are missing upon purchase.
User Name
Password
admin
null (leave it blank)
IP
Mask
Gateway
10.0.50.100
255.255.0.0
10.0.0.254
LED Indicators
Name
LAN
COM
RUN
LED
Orange
Green
Orange
Green
Red
Green
Status
On
Off
On
Blinking
On
Off
On
Off
On
Off
On
Blinking
Description
Ethernet is connected at 10Mbps
Ethernet is disconnected
Ethernet is connected at 100 Mbps
Data is transmitting on Ethernet
Data is transmitting on COM port (Tx)
Data is not transmitting on COM port (Tx)
Data is transmitting on COM port (Rx)
Data is not transmitting on COM port (Rx)
Device is powered on
Device is not powered on
Firmware is not running
Firmware is running normally
x Network Setting
Please set the appropriate IP setting for this
device (SE5404, 10.0.20.100).
DHCP (Obtain an IP automatically)
IP address:
Subnet mask:
Gateway:
Host name:
OK Cancel
10 100500
10 2540 0
255 255 0 0
Hardware Installation
1. Unpack the Serial Server; make sure it has not suffered any visible external
damages.
2. Proceed to do grounding on the device. This step is of extreme importance
since the back of the product has its ground metal side exposed. For grounding
just connect the corresponding grounding cable to the grounding point, make sure
the cable’s end has a solid contact with the grounding metal side.
Software Setup
DHCP (Dynamic IP):
A DHCP server can automatically assign an IP address and other related network
settings when SE8502-M12 acts as a DHCP Client; by default, the DHCP client
function on SE8502-M12 is disabled; you may activate the DHCP client function
by executing our Serial Manager© Utility.
Assign a Static IP address by:
■Configure by Telnet
■ Make sure the PC is on the same network as SE8502-M12.
■ Telnet to SE8502-M12 using DOS command “Telnet IP_address 23”.
Example: telnet 10.0.50.100 23.
■ SE8502-M12’s network, link mode and COM port settings can be configured
in the telnet window.
■Configure by Serial Manager© Utility
Use Serial Manager© Utility on Product CD to configure the SE8502-M12. First
click on “Config” then assign a static IP.
■Configure by Web Browser
■ Make sure the PC is on the same network as SE8502-M12.
■ Open a web browser; enter the IP address of SE8502-M12 in the address
bar. The default user name is admin and default password is null (leave it
blank).
■ SE8502-M12’s network, link mode and COM port settings can be configured on
different web pages.
■ Click on “Save Configuration” to save settings.
■ Click on “Restart” button to initiate the change if necessary.
3. Connect the device to a suitable power source.
4. Connect the device to the Ethernet network or a PC.
5. Always make sure that your PC is on the same network’s subnet as your
SE8502-M12.
6. Connect SE8502-M12’s serial port to a serial device.
7. Proceed then to mount your SE8502-M12 either to a wall or to your DIN rail
(depending on your current environment and choice of model).
ATTENTION:
Please make sure that the device is grounded properly before
proceeding.
Default Network Setting
LAN
IP68 Rated 2-Port Serial Server
SE8502-M12 Series
Hardware Installation Guide
Version 1.0
Updated on October, 2012
89900435G

Product Description
Mechanical Dimensions
Interfaces
LAN port pin assignment
Serial port
(8-pin female shielded
M12 socket with A coding)
and LED indicator
10/100BaseT(X) port
(4-pin female shielded M12
socket with D coding) and
indicator
Power input
(5-pin female shielded M12
socket with A coding) and
LED indicator
Serial port pin assignment
Power port pin assignment
NC = Not Assigned
Note:
Proper grounding will minimize the effects of noise due to electromagnetic
interference (EMI). Please install the ground connection from the ground screw to
the grounding surface before connecting the device.
Front View
Rear ViewSide ViewTop View
Without DIN-Rail
Grounding
Warranty Policy
─ Any changes to this material will be announced on Atop's website. ─
Warranty Conditions
Products supplied by Atop Technologies are covered in this warranty for sub-standard
performance or defective workmanship.
The warranty is not, however, extended to goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake
(c) Use of unqualified power supply, connectors, or unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" numberfrom Atop before shipping the
goods to be repaired to Atop. When in normal use, a sold product shall be replaced with a
new one within 3 months after purchase. The shipping cost from the customer to Atop will
be reimbursed by Atop.
After 3 months and still within the warranty period, it is up to Atop whether to replace the
unit with a new one; normally, as long as a product is under warranty, all parts and labor
are free of charge to the customers.
After the warranty period, the customer shall cover the cost for parts and labor.Three
months after purchase, the shipping cost from the customer to Atop will not be reimbursed,
but the shipping cost from Atop to the customer will be paid by Atop.
Limited Liability
Atop shall not be held responsible for any consequential losses from using Atop’s product.
Warranty Period
Rear ViewSide ViewTop View
Grounding
With DIN-Rail
The warranty certification will not be effective until an authorized stamp issued
by Atop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number:
Atop Customer Services and Supports
1. Please contact your local dealers or Atop Technical Support Center at the
following numbers.
+ 886-3-550-8137 (Atop Taiwan) / + 86-21-6495-6232 (Atop China)
2. Please report the defected problems via Atop’s Web site or E-mail account
Web Site：www.atop.com.tw, e-mail：[email protected]
Web Site：www.atop.com.cn, e-mail：[email protected]
Warranty
Product Categories
Ethernet Switches
Wireless
Serial Device Servers
Modbus Gateways
Embedded Device Servers
DIN-Rail Power Supplies
Power Adaptors
Antennas
Other Accessories
5 Years
1 Year
3 Years