ICP DAS USA PISO-813 User manual

PISO-813 Series Card
User Manual
32-channel Single-Ended Isolated A/D board Version 1.5, Feb. 2014
SUPPORTS
Board includes PISO-813 and PISO-813U.
WARRANTY
All products manufactured by ICP DAS are warranted against defective materials
for a period of one year from the date of delivery to the original purchaser.
WARNING
ICP DAS assumes no liability for damages consequent to the use of this product.
ICP DAS reserves the right to change this manual at any time without notice. The
information furnished by ICP DAS is believed to be accurate and reliable. However,
no responsibility is assumed by ICP DAS for its use, nor for any infringements of
patents or other rights of third parties resulting from its use.
COPYRIGHT
Copyright © 2014 by ICP DAS. All rights are reserved.
TRADEMARK
Names are used for identification only and may be registered trademarks of their
respective companies.
CONTACT US
If you have any question, please feel to contact us at:
[email protected]om; servic[email protected]m
We will give you quick response within 2 workdays.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 1
TABLE OF CONTENTS
1. INTRODUCTION ................................................................................................................................................. 3
1.1 PACKING LIST........................................................................................................................................................ 4
1.2 FEATURES ............................................................................................................................................................ 4
1.3 SPECIFICATIONS .................................................................................................................................................... 5
2. HARDWARE CONFIGURATION............................................................................................................................ 6
2.1 BOARD LAYOUT .................................................................................................................................................... 6
2.2 CARD ID SWITCH .................................................................................................................................................. 8
2.3 A/D CONVERTER OPERATION .................................................................................................................................. 9
2.3.1 A/D Conversion Block Diagram ................................................................................................................... 9
2.3.2 JP1: Analog Input Range Selection .............................................................................................................. 9
2.3.3 JP2: Analog Input Polarity Selection.......................................................................................................... 10
2.3.4 Setting Reference ........................................................................................................................................ 10
2.3.5 A/D Operation Flow..................................................................................................................................... 11
2.4 PIN ASSIGNMENTS............................................................................................................................................... 12
3. HARDWARE INSTALLATION ...............................................................................................................................13
4. SOFTWARE INSTALLATION ................................................................................................................................17
4.1 OBTAINING/INSTALLING THE DRIVER INSTALLER PACKAGE............................................................................................ 17
4.2 PNPDRIVER INSTALLATION ................................................................................................................................... 18
4.3 VERIFYING THE INSTALLATION ................................................................................................................................ 19
4.3.1 How do I get into Windows Device Manager? .............................................................................................. 19
4.3.2 Check that the Installation ............................................................................................................................ 21
5. TESTING PISO-813 SERIES CARD........................................................................................................................22
5.1 SELF-TEST WIRING .............................................................................................................................................. 22
5.2 EXECUTE THE TEST PROGRAM................................................................................................................................ 23
6. I/O CONTROL REGISTER ....................................................................................................................................25
6.1 HOW TO FIND THE I/O ADDRESS............................................................................................................................ 25
6.1.1 PIO_DriverInit ................................................................................................................................................ 26
6.1.2 PIO_GetConfigAddressSpace ......................................................................................................................... 28
6.1.3 Show_PIO_PISO............................................................................................................................................. 29
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 2
6.2 THE ASSIGNMENT OF I/O ADDRESS ........................................................................................................................ 30
6.3 THE I/O ADDRESS MAP ....................................................................................................................................... 32
6.3.1 RESET\ Control Register............................................................................................................................... 32
6.3.2 A/D Data Register.......................................................................................................................................... 33
6.3.3 Multiplexer Channel Select Register .............................................................................................................. 34
6.3.4 PGA Gain Code Register................................................................................................................................. 34
6.3.5 A/D Trigger Control Register.......................................................................................................................... 35
6.3.6 Card ID Register............................................................................................................................................. 35
7. DEMO PROGRAMS............................................................................................................................................36
7.1 DEMO PROGRAM FOR WINDOWS .......................................................................................................................... 36
7.2 DEMO PROGRAM FOR DOS .................................................................................................................................. 38
7.3 PIO_PISO UTILITY ............................................................................................................................................. 39
APPENDIX: DAUGHTER BOARD ....................................................................................................................................41
A1. DB-37 and DN-37................................................................................................................................................. 41
A2. DB-8325............................................................................................................................................................... 41
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 3
1. Introduction
The PISO-813U card is the new generation product that ICP DAS provides to meet RoHS compliance
requirement. The new PISO-813U card is designed as a drop-in replacement for the PISO-813, and
users can replace the PISO-813 by the PISO-813U directly without software/driver modification.
The PISO-813 series card is bus-typed isolated A/D board for IBM or compatible PC. The PISO-813U
universal PCI card supports 3.3 V/5 V PCI bus while the PISO-813 supports 5 V PCI bus. They feature
12-bit 32 single-ended analog inputs, 3750 Vrms bus-typed isolation protection and 10 kS/s data
acquisition under DOS and Windows. It is the most cost effective isolated A/D board for the
universal PCI/PCI Bus in the world.
The PISO-813U also adds a Card ID switch on-board. Users can set Card ID and then recognize the
board by the ID via software when using two or more PISO-813U cards in one computer.
These cards support various OS such as Linux, DOS, Windows 98, Windows NT, Windows 2000,
32-/64-bit Windows XP/2003/2008/Vista/7 and Windows 8. It also provides the DLL and Active X
control, and various language sample programs in Turbo C++, Borland c++, Microsoft C++, Visual
C++, Borland Delphi, Borland C++ Builder, Visual Basic, C#.NET, Visual Basic.NET and LabVIEW to
help users to quickly and easily develop their applications.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 4
1.1 Packing List
The shipping package includes the following items:
One PISO-813 series card hardware
One printed Quick Start Guide
One software utility CD
1.2 Features
Support the +5V PCI bus for PISO-813
Support the +3.3/+5 V PCI bus for PISO-813U
12-bit 10 kS/s A/D converter
32 single-ended analog input channels
3750 Vrms bus-type isolation protection
Built-in DC/DC converter with 3000 VDC protection
Analog input range:
Bipolar: ±10 V, ±5 V, ±2.5 V, ±1.25 V, ±0.625 V
Unipolar: 0~10 V, 0~5 V, 0~2.5 V, 0~1.25 V, 0~0.625 V
Supports Card ID (SMD Switch) for PISO-813U
Programmable gain control: 1, 2, 4, 8, 16
A/D trigger mode: Software Trigger
A/D data transfer mode: polling
SMD, Sort card
Note:
If any of these items is missing
or damaged, contact the dealer
from whom you purchased the
product. Save the shipping
materials and carton in case
you want to ship or store the
product in the future.
Quick Start
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 5
1.3 Specifications
Model Name
PISO-813U
PISO-813
Analog Input
Isolation Voltage
3750 Vrms (Bus Type)
Channels
32 single-ended
A/D Converter
12-it, 8 μs Coersio tie
Sampling Rate
10 kS/s. max.
FIFO Size
N/A
Over voltage Protection
Continuous +/-35 Vp-p
Input Impedance
 MΩ/6 pF
Trigger Modes
Software
Data Transfer
Polling
Accuracy
0.01 % of FSR ±1 LSB @ 25 °C, ± 10 V
Zero Drift
+/- 25 ppm/°C of FSR
General
Bus Type
3.3 V/5 V Universal PCI, 32-bit, 33
MHz
5 V PCI, 32-bit, 33 MHz
Data Bus
8-bit
Card ID
Yes(4-bit)
No
I/O Connector
Female DB37 x 1
Dimensions (L x W x D)
128 mm x 92 mm x 22mm
180 mm x 105 mm x 22 mm
Power Consumption
850 mA @ +5 V
Operating Temperature
0 ~ 60 °C
Storage Temperature
-20 ~ 70 °C
Humidity
5 ~ 85% RH, non-condensing
Analog Input Range
Gain
1
2
4
8
16
Bipolar
±10 V
±5 V
±5 V
±2.5 V
±2.5 V
±1.25 V
±1.25 V
±0.625 V
±0.625 V
Unipolar
0~10 V
0~5 V
0~2.5 V
0~1.25 V
0~0.625 V
Sampling Rate Max.
10 kS/s. max.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 6
2. Hardware Configuration
2.1 Board Layout
Board Layout of the PISO-813.
CON1
PCI BUS
PISO-813
PCI
controller
JP3
1
2
7
8
VR1 VR2 VR3 VR4
JP1 JP2
10V20V
UnipolarBipolar
3000Vdc photo-isolation
CON1
32-channel analog input, refer to Sec.2.4 for more detailed information.
JP1
Input range setting, refer to Sec. 2.3.1 for more detailed information.
JP2
Unipolar/Bipolar setting, refer to Sec. 2.3.2 for more detailed information.
JP3
Reserved
VR1~VR4
For manufacture calibration
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 7
Board Layout of the PISO-813U.
CON1
Universal PCI BUS
PISO-813U
PCI
controller
VR1 VR2 VR3 VR4
JP1 JP2
10V20V
UnipolarBipolar
3000Vdc photo-isolation
SW1
CON1
32-channel analog input Sec.2.4 for more detailed information.
JP1
Input range setting, refer to Sec. 2.3.1 for more detailed information.
JP2
Unipolar/Bipolar setting, refer to Sec. 2.3.2 for more detailed information.
SW1
Card ID function, refer to Sec. 2.2 for more detailed information.
VR1~VR4
For manufacture calibration
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 8
2.2 Card ID Switch
The PISO-813U has a Card ID switch (SW1) with which users can recognize the board by the ID via
software when using two or more PISO-813U cards in one computer. The default Card ID is 0x0. For
detail SW1 Card ID settings, please refer to Table 2.1. Note that the Card ID function is only
supported by the PISO-813U.
Table 2.1 (*) Default Settings; OFF 1; ON 0
Card ID (Hex)
1
ID0
2
ID1
3
ID2
4
ID3
(*) 0x0
ON
ON
ON
ON
0x1
OFF
ON
ON
ON
0x2
ON
OFF
ON
ON
0x3
OFF
OFF
ON
ON
0x4
ON
ON
OFF
ON
0x5
OFF
ON
OFF
ON
0x6
ON
OFF
OFF
ON
0x7
OFF
OFF
OFF
ON
0x8
ON
ON
ON
OFF
0x9
OFF
ON
ON
OFF
0xA
ON
OFF
ON
OFF
0xB
OFF
OFF
ON
OFF
0xC
ON
ON
OFF
OFF
0xD
OFF
ON
OFF
OFF
0xE
ON
OFF
OFF
OFF
0xF
OFF
OFF
OFF
OFF
NO
1 2 3 4
ID 0
ID 1
ID 2 ID 3
SW1
(Default Settings)
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 9
2.3 A/D Converter Operation
2.3.1 A/D Conversion Block Diagram
2.3.2 JP1: Analog Input Range Selection
JP1
10V
20V
JP1
10V
20V
Input Range = 20 V Input Range = 10 V
(Default Settings)
Analog Input
AI31
AI1
AI0
32-Channel
Analog
Multiplexer
Channel
select
D4~D0
Programm able
Gain Amplifier
PGA
Gain
Code
G2~G0
JP1
Input
Range
Select
JP2
Polarity
Select
A/D
Converter
Status&D11~D0
Trigger
Photocouple isolation
Control Logic
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 10
2.3.3 JP2: Analog Input Polarity Selection
UNI
BI
JP2
UNI
BI
Bipolar Mode Unipolar Mode
(Default Settings)
2.3.4 Setting Reference
Analog Input
JP2
Polarity Select
JP1
Range Select
Gain
-10 V ~ +10 V
Bipolar
20 V
1
-5 V ~ + 5 V
Bipolar
20 V
2
10 V
1
-2.5 V ~ +2.5 V
Bipolar
20 V
4
10 V
2
-1.25 V ~ +1.25 V
Bipolar
20 V
8
10 V
4
-0.625 V~ +0.625 V
Bipolar
20 V
16
10 V
8
0 ~10 V
Unipolar
10 V
1
0 ~ 5 V
Unipolar
10 V
2
0 ~ 2.5 V
Unipolar
10 V
4
0 ~ 1.25 V
Unipolar
10 V
8
0 ~ 0.625 V
Unipolar
10 V
16
Note: Refer to Sec.6.3.4 for more information about gain setting.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 11
2.3.5 A/D Operation Flow
Step 1: Find address-mapping of PISO-813(U). (Refer to Sec.6.1)
Step 2: Enable operation of PISO-813(U). (Refer to Sec.6.3.1)
Step 3: Make sure the range and polarity of the analog input signal. Select suitable Setting as show
in Sec.2.3.4.
Step 4: Select input channel. (Refer to Sec.6.3.3)
Step 5: delay 10 s. (for photocouple propagation delay and analog multiplexer settling time)
Step 6: Trigger A/D converter. (Refer to Sec.6.3.5)
Step 7: Delay 70 s. (for photocouple propagation delay and A/D conversion time)
Step 8: Read high byte of A/D conversion data. Check the status of A/D converter until conversion
ready. (Refer to Sec.6.3.2)
Step 9: Read low byte of A/D conversion data. (Refer to Sec.6.3.2)
Step10: A/D conversion complete.
Refer to the DEMO1.C of DOS Demo.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 12
2.4 Pin Assignments
The Pin assignments of CON1 for 37-pin D-type female connector on the PISO-813 and PISO-813U
are represented in the figure below.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 13
3. Hardware Installation
To install the PISO-813 series card, follow the procedure described below:
Step 1: Installing PISO-813 series card driver on your computer first.
For detailed information about
the driver installation, please
refer to Chapter 4 Software
Installation.
Step 2: Configuring Card ID by the SW1 DIP-Switch for PISO-813U only.
For detailed information about the card ID
(SW1), please refer to Sec. 2.2 Car ID
Switch .
Note:
It’s recoeded to istall drier first, sice soe operatig syste such as Widos 2000
may ask you to restart the computer again after driver installation. This reduces the times to
restart the computer.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 14
Step 3: Shut down and power off
your computer.
Step 4: Remove all covers from the
computer.
Step 5: Select an empty PCI slot.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 15
Step 6: Remove the PCI slot cover
form the PC.
Step 7: Remove the connector cover form
the PISO-813 series card.
Step 8: Carefully insert your
PISO-813 series card into the PCI
slot.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 16
Step 9: Tighten the screw.
Step 10: Replace the computer cover.
Step 11: Power on the computer.
Follow the prompt message to
finish the Plug&Play steps,
please refer to Chapter 4
Software Installation.
Confirm the PISO-813 series card is mounted on the
motherboard.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 17
4. Software Installation
This chapter provides a detailed description of the process for installing the PISO-813 series driver
and how to verify whether the PISO-813 was properly installed. PISO-813 series card can be used on
DOS, Linux and Windows 98/ME/2000 and 32-/64-bit XP/2003/Vista/7/8 based systems, and the
drivers are fully Plug and Play (PnP) compliant for easy installation.
4.1 Obtaining/Installing the Driver Installer Package
The driver installer package for the PISO-813 series card can be found on the supplied CD-ROM, or
can be obtained from the ICP DAS FTP web site. Install the appropriate driver for your operating
system. The location and addresses are indicated in the Table4-1 and Table 4-2 below.
Table 4-1: UniDAQ Driver/SDK
OS
Windows 2000、32/64-bit Windows XP、32/64-bit Windows 2003、
32/64-bit Windows Vista、32/64-bit Windows 7、32/64-bit Windows 2008、
32/64-bit Windows 8
CD-ROM
CD:\\ NAPDOS\PCI\UniDAQ\DLL\Driver\
Web Site
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
Driver Name
UniDAQ Driver/SDK (unidaq_win_setup_xxxx.exe)
Installing
Procedure
For detailed information about the UniDAQ driver installation, please refer to
UniDAQ DLL Software Manual.
The user manual is contained in:
CD:\NAPDOS\PCI\UniDAQ\Manual\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/manual/
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 18
Table 4-2: PISO-813 Series Classic Driver
OS
Windows 95/98/ME、Windows NT、Windows 2000、32-bit Windows XP、
32-bit Windows 2003、32-bit Windows Vista、32-bit Windows 7
CD-ROM
CD:\\ NAPDOS\PCI\PISO-813\DLL_OCX\
Web Site
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-813/dll_ocx/
Driver Name
PISO-813 Series Classic Driver
Win2K_XP_7 Folder
piso_813_win2K_xxx.exe
For Windows 2000, 32-bit Windows
XP/2003/Vista/7
Win98 Folder
piso_813_win98_xxx.exe
For Windows 95/98/ME
WinNT Folder
Piso_813_winnt_xxx.exe
For Windows NT 4.0
Installing Procedure
For detailed information about the PISO-813 series classic driver
installation, please refer to PISO-813 series classic DLL Software Manual.
The user manual is contained in: CD:\NAPDOS\PCI\PISO-813\Manual\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-813/manual/
4.2 PnP Driver Installation
Power off the computer and install the PISO-813 series cards. Turn on the computer and Windows
95/98/ME/NT/2000 and 32-/64-bit Windows XP/2003/Vista/7/8 should automatically defect the
new PCI device(s) and then ask for the location of the driver files for the hardware. If a problem is
encountered during installation, refer to the PnPinstall.pdf file for more information.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru

PISO-813 Series Card
32-channel Single-Ended Isolated A/D Board
User Manual, Ver. 1.5, Feb. 2014, PMH-003-15, Page: 19
4.3 Verifying the Installation
Please open the Device Manager to verify the installation. Below are the steps for entering the
Device Manager in each of the major versions of windows. Refer to appropriate for your OS,
continue to complete the following steps:
4.3.1 How do I get into Windows Device Manager?
Microsoft Windows 95/98/ME users
Step 1: On the desktop right-click on My Computerand click Propertiesor open the Control
Paneland double-click the Sste icon.
Step 2: Click the Device Managertab.
Microsoft Windows 2000/XP users
Step 1: Select StartSettingsControl
Paneland double-click the System
icon.
Step 2: Click the Hardwaretab and then
click the Device Manager button.
Microsoft Windows 2003 users
Step 1: Open the Adiistrative Tools in Control Panel.
Step 2: Within the Administrative Tools click Coputer Maageet.
ГК Атлант Инжиниринг – официальный представитель вРФ иСНГ
[phone] [email protected] www.bbrc.ru