AtVideo HDB2212M User manual

INSTRUCTION MANUAL
FULL HD BULLET CAMERA
Please read this manual thoroughly before use and keep it handy for future reference.

2
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC INFORMATION : This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
CAUTION : Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
WARNING : This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.

3
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.\
3. Heed all warnings.
4. Follow all instructions.
5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the cart, stand, tripod, bracket, or table specified by
The manufacturer, or sold with the apparatus. When a cart is used,
Use caution when moving the cart/ apparatus combination to avoid
Injury from tip-over.
9. CAUTION –THESE SERVICING IN STRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
10. Use satisfy clause 2.5 of IEC60950-1/UL 60950-1 or Certified/Listed Class 2 power
source only.
11. Indoor use only.
EXPLANATION OF GRAPHICAL SYMBOLS
The lighting flash with arrowhead symbol, within an equilateral triangle, is
Intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product`s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

4
CONTENTS
•INTRODUCTION 5
•CONNECTIONS & VIDEO OUT CHECK (CVBS) 6
•LENS ADJUSTMENT 6
•CONTENTS OF PACKAGE 6
•BASE INSTALLATION 7
•STRUCTURE OF THE SETUP MENU 8
•DC AUTO IRIS LENS 16
•SPECIFICATIONS 17
•EXTERNAL DIMENSION 18

5
INTRODUCTION
The 1/2.9”2.1M Full HD CMOS camera, especially for closed circuit television
CCTV and security surveillance application.
Features:
•High performance SONY 1/2.9” 2.1M EXMOR CMOSTM
•1.0 lux(Color), 0 lux(BW, IR LED ON)
•Auto electronic shutter [1/60(1/50) ~ 1/50,000] and manual electronic shutter modes
•25/30 fps @ 1080p
•BLC (Back-light compensation)
•Auto and manual white balance modes (ATW/AWC/Manual/AWB)
•Day & Night (ICR) : Auto / Color / BW
•OSD (on screen display)
•3 DNR (Digital Slow Shutter)
•DWDR
•Smart IR
•30EA, 850nm IR LED
•IR Range distance up to 30M
•Privacy mask Function (4 zone)
•Motion Detection
•Defog
•HSBLC
•Operates in DC 12V ± 10%
•Use Certified / Listed Class 2 Power source only
IMPORTANT : The user of this camera is responsible for checking and
complying with local, state, and federal laws and statutes concerning the
recording and monitoring of audio signals.

6
CONNECTIONS & VIDEO OUT CHECK(CVBS)
①Power : 12V DC input, Use Certified/Listed Class 2 power source only.
* If using DC 12V power adaptor, use power supply capable of supplying 7 Watts.
②Video : BNC connector used to connect the camera to a DVR, etc.
③SPOT : Spot connector used to check video output.
④Video Out Mode (HD↔CVBS) : Select Between the video output mode from the
Video(BNC) & SPOT
LENS ADJUSTMENT
Field of View : Adjust setting from Tele (T) to Wide (W) field of View
Focus : Adjust lens focus from near (N) to infinity (∞)
CONTENTS OF PACKAGE
The package contents the following.
Camera in Housing…………………………………………….….1
Instruction Manual (This Document)………………………….. 1
Accessory Kit for Installing……………………………………… 1
REMINDER:
Never aim the camera directly into the sun.

7
BASE INSTALLATION
3X20mm Tapping Screws Tension adjustment screw
Position camera for best field of view then tighten camera/mount
Tension adjustment screws (x2)
Caution
“Adjusting the position of the camera after
installation could potentially damage the cable”

8
STRUCTURE OF THE SETUP MENU
<SETUP>
LENS
EXPOSURE
BACKLIGHT
WHITE BAL
DAY&NIGHT
IMAGE
FUNCTION
SYSTEM
AF
EXIT
<LENS>
DC
MANUAL
<EXPOSURE>
SHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
RETURN
<BACKLIGHT>
OFF
BLC
HSBLC
<WHITE
BAL>
ATW
AWC->SET
INDOOR
OUTDOOR
MANUAL
AWB
<DAY&NIGHT
>
AUTO
COLOR
B&W
<IMAGE>
SHARPNESS
LSC
D-EFFECT
RETURN
<FUNCTION>
DNR
MOTION
PRIVACY
DEFECT DET
RETURN
<SYSTEM>
CAMTITLE
MONITOR
VIDEO OUT
LANGUAGE
COMET
RETURN
<AF>
AF MODE
ONE SHOT AF
TDN AF
LENS LINT
RETURN
<RESET>
SAVE&END
RESET
NOT SAVE

9
LENS
The EXPOSURE menu is used to set the automatic light control method for the camera.
It provides the ability to adjust the SHUTTER speed. AGC SENS-UP, BRIGHTNESS, D-WDR, and
DEFOG functions of the camera.
1) DC Select the DC mode. ▶INDOOR, OUTDOOR
Select the DC iris speed ▶0~15
2) MANUAL Select the MANUAL mode
<LENS> Mode
EXPOSURE
The EXPOSURE menu is used to set the automatic light control method for the camera.
It provides the ability to adjust the SHUTTER speed, AGC, SENS-UP, BRIGHTNESS,
D-WDR, and DEFOG functions of the camera.
1) SHUTTER Select the SHUTTER speed level.
▶Auto, 1/60(50), FLK~1/240 –1/50000, x2 ~ x30
2) AGC Adjust the Auto Gain Control level. ▶OFF, Auto (x2 ~ x30)
3) SENS-UP Select the Digital Slow Shutter level. ▶OFF, AUTO (x2 ~ x30)
4) BRIGHTNESS Adjust the BRIGHTNESS level. ▶0 - 100
5) D-WDR Select the Digital WDR. ▶AUTO, ON(level 0~8), OFF
6) DEFOG Select the DEFOG mode.▶AUTO, ON(level 0~8), OFF
POS/SIZE Adjust the window position & size
GRADATION ▶0 ~ 2
DEFAULT Initialize the setting values
MAIN MENU
OUTDOOR MODE
DC LENS MODE
LENS
DC
MIN SHU.
1/25(30)
EXPOSURE

MODE
OUTDOOR
MAX SHU.
1/2000
BACKLIGHT
OFF
IRIS SPEED
 8
RETURN
RET
WHITE BAL
ATW
RETURN
RET
DAY&NIGHT
AUTO
IMAGE

FUNCTION

SYSTEM

AF

EXIT
SAVE&END
NOTE Choose when installed in an external DC mode outdoor.

10
<EXPOSURE> Mode
BACKLIGHT
The BACKLIGHT menu is used to the ability to prevent back lighting from the image.
1) BLC Prevents such a back light effect to secure a clear image under All illumination
environments.
Adjust the size of Back Light Compensation area.
LEVEL Select the BLC gain ▶Low, Middle, High
AREA Adjust the window position & size
DEFAULT Initialize the setting values
2) HSBLC Mask the high light zone with specific color & level.
SELECT Select the HSBLC area ▶AREA1 - AREA4
DISPLAY Adjust the HSBLC area window position & size
BLACK MASK Select the BLACK MASK ▶ON, OFF
LEVEL Select the HSBLC level ▶0 ~ 100
MODE All Day, Night
DEFAULT Initialize the setting values.
<BACK LIGHT> Mode
MAIN MENU
SENS-UP
EXPOSURE
LENS
DC
SENS-UP
x2
EXPOSURE

SHUTTER
---
RETURN
RET
BACKLIGHT
OFF
AGC
 14
WHITE BAL
ATW
SENS-UP
AUTO
D-WDR
DAY&NIGHT
AUTO
BRIGHTNESS
 40
IMAGE

D-WDR
ON
LEVEL
 5
FUNCTION

DEFOG
OFF
RETURN
RET
SYSTEM

RETURN
RET
AF

DEFOG
EXIT
SAVE&END
POS/SIZE

GRADATION
 0
DEFAULT

RETURN
RET
MAIN MENU
BLC
HLBLC
LENS
DC
EXPOSURE

LEVEL
MIDDLE
SELECT
AREA1
BACKLIGHT
OFF
AREA

DISPLAY
ON
WHITE BAL
ATW
DEFAULT

BLACK MASK
ON
DAY&NIGHT
AUTO
RETURN
RET
LEVEL
 20
IMAGE

MODE
NIGHT
FUNCTION

DEFAULT

SYSTEM

RETURN
RET
AF

EXIT
SAVE&END
NIGHT MODE
AGC LEVEL
 150
RETURN
RET

11
WHITE BALANCE
The screen color can be adjusted by using the Auto White Balance function.
It compensates for deviations in the white color caused by changes in the color
temperature of the light source so that the colors are reproduced correctly.
1) ATW Automatically adjust color temperature.
2) AWC->SET Automatically readjust only by pressing AWC→SET.
3) INDOOR Set the color temperature to 3200°K
4) OUTDOOR Set the color temperature to 6300°K
5) MANUAL Manual mode.
User can change Red and Blue gain value manually.
BLUE 0 ~ 100
RED 0 ~ 100
6) AWB Automatically extended range of color temperature adjustment.
<WHITE BALANCE> Mode
DAY&NIGHT
The DAY&NIGHT menu is used to configure the day and night related setting for the camera.
1) D&N AUTO
-Input Method CDS
DAY&NIGHT Mode are changed according to the sensor inputs
D&N LEVEL Adjust levels of transition ▶0 - 255
N&D LEVEL Adjust levels of transition ▶0 - 255
DELAY 1-60 SEC
-Input Method AGC
DAY&NIGHT mode are changed according to the brightness of the image.
Use only when the camera is installed in a dark place but the camera is viewing a bright place.
When used in a normal installation, hunting may occur.
D&N LEVEL Adjust levels of transition ▶0 - 255
N&D LEVEL Adjust levels of transition ▶0 - 255
DELAY 1-60 SEC
2) D&N B&W
IR SMART LEVEL 1~15
AREA Adjust the window position & size.
MAIN MENU
MANUAL
LENS
DC
EXPOSURE

BLUE
 50
BACKLIGHT
OFF
RED
 50
WHITE BAL
ATW
RETURN
RET
DAY&NIGHT
AUTO
IMAGE

FUNCTION

SYSTEM

AF

EXIT
SAVE&END

12
<DAY & NIGHT> Mode
IMAGE
The IMAGE menu provides the ability to adjust the SHARPNESS, LSC and D-EFFECT functions of the
camera.
1) SHARPNESS Adjust the SHARPNESS level. ▶OFF, AUTO (0 - 10)
2) LSC Select the Lens Shading Compensation. ▶ON, OFF
3) D-EFFECT FREEZE Select real or still mode ▶ON, OFF
MIRROR Select OFF, MIRROR, V-FLIP, ROTATE
NEG. IMAGE Select Negative image mode ▶ON, OFF
<IMAGE> Mode
FUNCTION
The IMAGE menu provides the ability to adjust the DNR, MOTION, PRIVACY and DEFECT DET
functions of the camera.
1) DNR Select Digital Noise Reduction.
2D ▶OFF, LOW, MIDDLE, HIGH
3D ▶OFF, LOW, MIDDLE, HIGH
2) MOTION Detects the Motioned Object in the image. ▶ON, OFF
MAIN MENU
D&N AUTO
B/W
LENS
DC
EXPOSURE

DN (CDS)
 205
BURST
OFF
BACKLIGHT
OFF
DN (DELAY)
 3
IR SMART
ON
WHITE BAL
ATW
ND (CDS)
 165
RETURN
RET
DAY&NIGHT
AUTO
ND (DELAY)
 3
IMAGE

RETURN
RET
FUNCTION

SYSTEM

AF

EXIT
SAVE&END
IR SMART
LEVEL
 8
AREA

RETURN
RET
MAIN MENU
SHARPNESS
IMAGE
LENS
DC
LEVEL
 6
EXPOSURE

SHARPNESS
AUTO
START AGC
 120
BACKLIGHT
OFF
LSC
ON
END AGC
 255
WHITE BAL
ATW
D-EFFECT

RETURN
RET
DAY&NIGHT
AUTO
RETURN
RET
IMAGE

D-EFFECT
FUNCTION

SYSTEM

FREEZE
OFF
AF

MIRROR
OFF
EXIT
SAVE&END
NEG.IMAGE
OFF
RETURN
RET

13
SELECT Select the Motion area ▶AREA1 - AREA4
DISPLAY Adjust the Motion area window position & size
SENSITIVITY Adjust the Motion sensitivity level ▶0 - 100
COLOR Select the motion area color
▶WHITE - Red, Green, Blue
TRANS Select the motion area transparency.
▶1.0, 0.75, 0.5, 0.25
ALARM Select the Motion alarm
VIEW TYPE Select view type of the Motion area
▶OFF, BLOCK, OUTLINE, ALL
OSD VIEW Select the Motion OSD view ▶OFF, ON
TIME Select the Motion Alarm time ▶1 - 15
DEFAULT Initialize the setting values
3) PRIVACY Hide an area you want to hide on the screen.
SELECT Select the privacy zone ▶AREA1 - AREA4
DISPLAY Adjust the Privacy window type, position & size
▶OFF, INV., MOSAIC, COLOR
COLOR Select the privacy zone color ▶WHITE - USER
TRANS Select the privacy zone transparency ▶1.0, 0.75, 0.5, 0.25
DEFAULT Initialize the setting values
4) DEFECT DET Compensates for bad pixels.
LIVE DPC Select the Live DPC mode ▶OFF, ON
AGC LEVEL Select the AGC level ▶0 - 255
LEVEL Select the Live DPC level ▶0 - 100
WHITE DPC Select the White DPC mode ▶OFF, ON
POS/SIZE Adjust the White DPC area window position & size
START Start the white pixels correction
DPC VIEW ▶OFF, ON
LEVEL Select the White DPC level ▶0 - 60
AGC Select the AGC Level ▶0 - 14
SENS-UP Select the Sens-up level ▶x2 - x30
BLACK DPC Select the Black DPC mode ▶OFF, ON
POS/SIZE Adjust the Black DPC area window position & size
START Start the Black pixels correction
DPC VIEW ▶OFF, ON
LEVEL Select the Black DPC level ▶0 - 100
<FUNCTION> Mode
DNR
FUNCTION
2DNR
MIDDLE
DNR

3DNR
MIDDLE
MOTION
OFF
RETURN
RET
PRIVACY
OFF
DEFECT DET

MOTION
ALARM
RETURN
RET
SELECT
AREA1
VIEW TYPE
ALL
DISPLAY
ON
OSD VIEW
ON
SENSITIVITY
 64
TIME
 3
COLOR
GREEN
RETURN
RET
TRANS.
1.00
ALARM

DEFAULT

RETURN
RET

14
PRIVACY
SELECT
AREA1
DISPLAY
COLOR
COLOR
WHITE
TRANS.
1.00
DEFAULT

RETURN
RET
DEFECT DET
LIVE DPC
LIVE DPC
ON
AGC LEVEL
 16
WHITE DPC
ON
LEVEL
 100
BLACK DPC
OFF
RETURN
RET
RETURN
RET
WHITE DPC
CLOSE THE IRIS
POS/SIZE

START

THEN
DPC VIEW
OFF
LEVEL
 16
PRESS ENTER
AGC
 14
SENS-UP
x8
RETURN
RET
BLACK DPC
POS/SIZE

PRESS ENTER
START

DPC VIEW
OFF
LEVEL
 100
RETURN
RET
SYSTEM
The SYSTEM menu provides the ability to adjust the CAM TITLE, RS485, MONITOR, CVBS CROP,
VIDEO OUT, LANGUAGE and VERSION functions of the camera.
1) CAM TITLE Maximum of 15 characters are allowed.
2) MONITOR Select the Monitor type ▶LCD, CRT
LCD
BLUE GAIN Adjust the Blue gain level ▶0 - 100
RED GAIN Adjust the Red gain level ▶0 - 100
GAMMA Select the gamma level ▶USER, 0.45 - 1.0
CRT
BLUE GAIN Adjust the Blue gain level ▶0 - 100
RED GAIN Adjust the Red gain level ▶0 - 100
GAMMA Select the gamma level ▶USER, 0.45 - 1.0
4) VIDEO OUT Select the video out type ▶NTSC, PAL
5) LANGUAGE OSD menu LANGUAGE (16ea) ▶ENGLISH etc.

15
<SYSTEM> Mode
AF
The AF menu provides the ability to adjust the AF MODE, ONE SHOT AF, TDN AF and LENS INIT
functions of the camera.
1) AF MODE Semi, Auto, Manual.
SEMI Waits until the zoom function has finished before focusing
AUTO Tracks closely with the zoom
MANUAL Once the camera is zoomed in using Semi or Auto, the Up / Down
buttons allow manual focusing
2) ONE SHOT AF Will focus the camera
3) TDN AF Will refocus when switching between color/B&W and B&W /color ▶Off / On
4) LENS INIT Reinitializes the lens
<AF> Mode
MAIN MENU
CAMERA TITLE
SYSTEM
LENS
DC
0 1 2 3 4 5 6 7 8 9
EXPOSURE

CAM TITLE
OFF
A B C D E F G H I J K
BACKLIGHT
OFF
MONITOR
LCD
L M N O P Q R S T U V
WHITE BAL
ATW
VIDEO.OUT
NTSC
W X Y Z ( )
DAY&NIGHT
AUTO
LANGUAGE
ENG
¯ ─ _ / = & : ~ , .
IMAGE

RETURN
RET
FUNCTION

CLR POS END
SYSTEM

AF

------------
EXIT
SAVE&END
LCD
GAMMA
USER
BLUE GAIN
 50
RED GAIN
 50
RETURN
RET
CRT
BLUE GAIN
 50
RED GAIN
 50
RETURN
RET
MAIN MENU
AF
LENS
DC
EXPOSURE

AF MODE
SEMI
BACKLIGHT
OFF
ONE SHOT
AF

WHITE BAL
ATW
TDN AF
OFF
DAY&NIGHT
AUTO
LENS INIT

IMAGE

RETURN
RET
FUNCTION

SYSTEM

AF

EXIT
SAVE&END

16
EXIT
The EXIT menu provides the ability to adjust the RESET, SAVE & END and NOT SAVE functions of the
camera.
1) EXIT
RESET Factory initialization of camera settings
SAVE & END Save and exit menu
NOT SAVE Exiting the menu without saving
DC AUTO IRIS LENS
Image Size
1/2.9” CMOS
Focal Length
2.8-12mm
Aperture Ratio
1:1.4
Angular
Field of View
DIAGONAL
2.8mm : 130º
12mm : 37º

17
EXTERNAL DIMENSION

18
SPECIFICATIONS
MODEL
2M HD Bullet CAMERA
Power
Power Source
DC12V ± 10%
Power Consumption
MAX 6.6 Watts (500mA)
General
Image sensor
1/2.9" 2.1M Sony CMOS
Total Pixels
2000(H) x 1121(V)
Active Pixels
1920(H) x 1080(V)
Scanning system
Progressive
Sync. System
Internal
Video Frame Rate
1920x1080p@25 fps ; 1920x1080p@30 fps
CVBS Resolution
1000 TVL
Min. illumination
1.0 lux(COLOR), 0 lux(BW, IR LED ON)
Video Output
BNC (AHD / CVBS Selectable)
IR
IR LED
30ea IR LED (850nm)
DISTANCE
30M
Camera Control
OSD Menu (Joystick Switch, coaxial control)
S/N Ratio
More than 50dB (AGC off)
Function
Lens
DC / MANUAL
Exposure
Shutter
AUTO, 1/60, FLK ~ 1/50,000 sec
AGC
1 ~ 15
Sens-UP
OFF / AUTO (x2, x4, x6, x8, x10, x15, x20, x25, x30)
Brightness
1 ~ 100
D-WDR
OFF / ON / AUTO
Defog
OFF / AUTO
Backlight
OFF / BLC / HSBLC
White Balance
ATW / AWC / INDOOR / OUTDOOR / MANUAL/AWB
Day & Night
AUTO / COLOR / B&W
DNR
2DNR
OFF / LOW / MIDDLE / HIGH
3DNR
OFF / LOW / MIDDLE / HIGH
S
P
E
C
I
A
L
Camera Title
OFF / ON
D-Effect
OFF / FREEZE / MIRROR / NEG.IMAGE
Motion Detection
OFF / ON (4 zone)
Privacy Masking
OFF / ON (4 zone)
Language
ENG / CHN1 / CHN2 / GER / FRA/ ITA/ SPA/ POL
/ RUS / POR / NED /TUR / KOR / JPN / HEB / ARB
Defect Detection
LIVE DPC / WHITE DPC / BLACK DPC
Sharpness
OFF / AUTO (0 ~ 10)
Monitor
CRT / LCD
LSC (Shading)
OFF / ON
Video mode
NTSC / PAL
AF
AF Mode
SEMI / AUTO / MANUAL
One Shot AF
Enter
TDN AF
OFF / ON
Lens Initialize
Enter
Save & Exit
SAVE & EXIT / NOT SAVE / RESET
Connector
&
etc.
Power input
DC Jack
Video out
BNC Connector(AHD/CVBS)
Transmission Distance
Over 500m via 5C-2V coaxial cable
Lens Mount
Fixed mount
Lens
2 Motor, f=2.8~12mm F1.4~360 Varifocal, ICR (D&N)
Operating temperature
14ºF ~ 122ºF (-10ºC ~ +50ºC)
Operating humidity
0 ~ 96% (non-condensing)
External dimension
Φ66 x 173 mm(H)
Weight
450g
Ingress Protection
IP66

19
FULL HD BULLET CAMERA
5030xxxxA