Sony HDC1000 series User manual

HD COLOR CAMERA
HDC1000
HDC1400
HDC1500
HDC1550
HDC1580
MAINTENANCE MANUAL
Volume 1 1st Edition (Revised 4)
Serial No. 10001 and Higher: HDC1000 (UCJ)
Serial No. 40001 and Higher: HDC1000 (CE)
Serial No. 10001 and Higher: HDC1400 (UC)
Serial No. 10001 and Higher: HDC1500 (SY)
Serial No. 40001 and Higher: HDC1500 (CE)
Serial No. 10001 and Higher: HDC1550 (UC)
Serial No. 40001 and Higher: HDC1550 (CE)
Serial No. 400001 and Higher: HDC1550 (CE)
Serial No. 50001 and Higher: HDC1580 (CN)

HDC1000/V1(E)
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
CAUTION
The use of optical instruments with this product
will increase eye hazard.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
This HD Color Camera is classified as a CLASS 1
LASER PRODUCT.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
Laser Diode Properties
Wave length : 1310 ±40 nm
Emission duration : Pulse Modulation
Laser output power : 141 +37 uW
_29

HDC1000/V1(E)
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandépar le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning måkun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitäkäytetty paristo valmistajan ohjeiden
mukaisesti.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
1 (P)

HDC1000/V1(E)
Voor de klanten in Nederland
Gooi de batterij niet weg maar lever deze in als klein
chemisch afval (KCA).
Für Kunden in Deutschland
Entsorgungshinweis: Bitte werfen Sie nur entladene
Batterien in die Sammelboxen beim Handel oder den
Kommunen. Entladen sind Batterien in der Regel dann,
wenn das Gerät abschaltet und signalisiert “Batterie
leer”oder nach längerer Gebrauchsdauer der Batterien
“nicht mehr einwandfrei funktioniert”. Um
sicherzugehen, kleben Sie die Batteriepole z.B. mit
einem Klebestreifen ab oder geben Sie die Batterien
einzeln in einen Plastikbeutel.
2 (P)
For the customers in Taiwan only

1
HDC1000/V1(E)
Table of Contents
Manual Structure
Purpose of this manual ................................................................. 4
Related manuals ........................................................................... 4
1. Service Overview
1-1. Checking before Installation ........................................... 1-1
1-1-1. Checking the ROM and Software Version ............ 1-1
1-2. Connectors and Cables ................................................... 1-2
1-2-1. Connector Input/Output Signals ............................ 1-2
1-2-2. Wiring Diagrams for Cables ................................. 1-9
1-2-3. Connection Connectors/Cables ........................... 1-10
1-2-4. Note in Connecting CCU Connector
(HDC1000/1400/1500/1580) .............................. 1-10
1-3. Location of Printed Circuit Boards ............................... 1-11
1-4. Opening/Closing the Side Panel ................................... 1-14
1-5. Switch Settings ............................................................. 1-15
1-6. Notes for Replacing Parts ............................................. 1-19
1-6-1. Notes for Replacing the Flexible Card Wire .......1-19
1-6-2. Notes for Replacing the Board ............................ 1-20
1-6-3. Notes for Replacing the Connector
on the Board ........................................................1-20
1-6-4. Notes for HDC1400 and HDC1580 .................... 1-20
1-7. Cleaning the Vent Portion of the Fan
(HDC1400/1500/1550/1580) ........................................ 1-21
1-8. Cleaning of Connector/Cable
(HDC1000/1400/1500/1580) ........................................ 1-22
1-8-1. When the Optical Connector Cleaner
(Commercially Available) is Available ............... 1-22
1-8-2. When the Optical Connector Cleaner
(Commercially Available) is not Available ........ 1-23
1-9. Setting the Utility Out Voltage (HDC1000) ................. 1-24
1-10. Notes on Flexible Card Wire ........................................ 1-24
1-10-1. Disconnecting/Connecting Flexible Card
Wire ..................................................................... 1-24
1-10-2. Forming of the Flexible Card Wire ..................... 1-26
1-11. Notes on Replacement of Circuit Board .......................1-27
1-11-1. Description on EEPROM Data ........................... 1-27
1-11-2. Adjustment after Replacement of Board .............1-27
1-11-3. Adjustment and Setting Items when
Replacing AT-163 Board .................................... 1-27
1-12. Setting Microphone Power and Intercoms ................... 1-28
1-12-1. How to Supply a Power of +12 V ....................... 1-28
1-12-2. Setting Intercoms ................................................. 1-28
1-13. Upgrading the Software ................................................ 1-29
1-13-1. Upgrading the MAIN Program ........................... 1-29
1-13-2. Upgrading the Boot Program .............................. 1-30
1-14. Writing and Rewriting the PLD Internal Data .............. 1-31
1-15. Note on Replacement of Lithium Battery ..................... 1-32
1-16. Recommended Replacing Parts .................................... 1-33
1-16-1. HDC1000 ............................................................ 1-33
1-16-2. HDC1400/1500/1550/1580 ................................. 1-34
1-16-3. Periodic Check/Replacement Parts ..................... 1-35
1-17. Description of CCD Block Number ............................. 1-36
1-18. Optional Fixtures .......................................................... 1-36
1-19. Notes on Repair Parts ................................................... 1-36
1-20. Unleaded Solder ............................................................ 1-36
2. Replacement of Main Parts
2-1. Replacing the CCD Unit .................................................2-1
2-1-1. HDC1000 .............................................................. 2-1
2-1-2. HDC1400/1500/1550/1580 ................................... 2-3
2-2. Replacement of CCD Unit Boards ................................. 2-4
2-2-1. DR-528 Board ....................................................... 2-4
2-2-2. CN-2579 Board ..................................................... 2-4
2-2-3. PA-317 Board ........................................................ 2-5
2-2-4. TG-243 Board ....................................................... 2-5
2-2-5. CN-2578 Board ..................................................... 2-6
2-3. Replacing the Filter Disk Unit ........................................2-7
2-3-1. HDC1000 .............................................................. 2-7
2-3-2. HDC1400/1500/1550/1580 ................................... 2-7
2-4. Replacing the Fan (HDC1000) ....................................... 2-8
2-4-1. DC Fan (TOP) ....................................................... 2-8
2-5. Replacing the Fan (HDC1400/1500/1550/1580) ............ 2-9
2-5-1. DC Fan (Front) ......................................................2-9
2-5-2. DC Fan (Rear) ..................................................... 2-10
2-6. Replacing the VF DISP Switches
(HDC1400/1500/1550/1580) (SW-1237 Board) .......... 2-11
2-7. Replacing the Side Switch Panel Assembly
(HDC1400/1500/1550/1580) (SW-1240 Board) .......... 2-12

2HDC1000/V1(E)
2-8. Replacing the Connectors
(HDC1400/1500/1550/1580) ........................................ 2-12
2-8-1. EARPHONE Jack (CN-2640 Board) .................. 2-12
2-8-2. DC IN Connector (CN-2623 Board) ................... 2-13
2-8-3. INTERCOM 1/2 Connector
(CN-2618 Board) ................................................. 2-14
2-8-4. LENS Connector (CN-2616 Board) ....................2-14
2-8-5. MIC 1 IN Connector (CN-2615 Board) .............. 2-15
2-8-6. REMOTE Connector (CN-2622 Board) ............. 2-15
2-8-7. RET IN, TEST OUT Connector
(CN-2620 Board) ................................................. 2-16
2-8-8. SDI 1 Connector (HDC1500) .............................. 2-16
2-8-9. SDI 2 Connector (HDC1500)
SDI Connector (HDC1400/1550) ........................ 2-17
2-8-10. BUILD UP Connector
(Hot Shoe Assembly) .......................................... 2-17
2-9. Replacing the Encapsulated Cable Assembly/
TRIAX Assembly ......................................................... 2-18
2-9-1. HDC1000 (Encapsulated Cable Assembly) ........ 2-18
2-9-2. HDC1400/1500/1580
(Encapsulated Cable Assembly) .......................... 2-19
2-9-3. HDC1550 (TRIAX Assembly) ............................ 2-20
2-10. Replacing the DC/DC Converter Unit ..........................2-21
2-10-1. HDC1000 ............................................................ 2-21
2-10-2. HDC1400/1500/1550/1580 ................................. 2-21
2-11. Replacing the Switching Regulator .............................. 2-22
2-11-1. HDC1000 ............................................................ 2-22
2-11-2. HDC1400/1500/1580 .......................................... 2-23
2-11-3. HDC1550 ............................................................ 2-24
2-12. Replacing the Boards (HDC1000) ................................ 2-25
2-12-1. MB-1060 Board ................................................... 2-25
2-13. Replacing the Boards (HDC1400/1500/1550/1580) .... 2-28
2-13-1. CN-2617 Board ................................................... 2-28
2-13-2. MB-1059 Board ................................................... 2-29
2-14. Checking SDI-84 Board (HDC1400/1500/1580) ......... 2-30
3. Electrical Alignment
3-1. Preparations .................................................................... 3-1
3-1-1. Equipment Required .............................................. 3-1
3-1-2. Precautions on Adjustments ..................................3-1
3-1-3. File Data at Adjustment ......................................... 3-1
3-1-4. Maintaining the Grayscale Chart ........................... 3-2
3-1-5. Description on Setup Menu ................................... 3-4
3-1-6. Connection of Equipment ...................................... 3-5
3-1-7. Initial Settings ....................................................... 3-6
3-1-8. Adjustment Items and Setup Menu Items ............. 3-7
3-2. Automatic Adjustment .................................................... 3-8
3-3. Electrical Alignment ....................................................... 3-8
3-3-1. Clamp Level Adjustment between Channel A
and Channel B ....................................................... 3-8
3-3-2. BLACK SET Adjustment ...................................... 3-9
3-3-3. Sensitivity Adjustment .......................................... 3-9
3-3-4. V-SUB Adjustment ............................................. 3-10
3-3-5. BLACK SHADING Adjustment ......................... 3-11
3-3-6. White Shading Adjustment ................................. 3-11
3-3-7. RPN Adjustment .................................................3-13
3-4. Video System Level Adjustment .................................. 3-14
3-4-1. H/V Ratio Adjustment ......................................... 3-14
3-4-2. Detail Level Adjustment ..................................... 3-15
3-4-3. Crispening Adjustment ........................................ 3-15
3-4-4. Level Dependent Adjustment .............................. 3-16
3-4-5. Detail Clip Adjustment ........................................ 3-16
3-4-6. Auto-iris Adjustment ........................................... 3-17
3-4-7. Pedestal Level Adjustment .................................. 3-18
3-4-8. Flare Adjustment ................................................. 3-18
3-4-9. Gamma Correction Adjustment .......................... 3-19
3-4-10. Knee Point/Knee Slope Adjustment .................... 3-19
3-4-11. White Clip Level Adjustment ............................. 3-20
3-4-12. File Store ............................................................. 3-21
3-5. ND Offset Adjustment ..................................................3-22
3-6. Adjustment Preparation of HDC1550 .......................... 3-23
3-6-1. Equipment Required ............................................ 3-23
3-6-2. Precautions on Adjustments ................................3-23
3-6-3. Connection .......................................................... 3-24
3-7. TONE Adjustment (HDC1550) ....................................3-25
3-7-1. CHU DATA/TONE Frequency Adjustment .......3-25
3-7-2. CCU DATA Demodulation Adjustment .............3-25

3
HDC1000/V1(E)
3-8. Video System Adjustment (HDC1550) ........................ 3-26
3-8-1. Demodulation Tuning Adjustment ...................... 3-26
3-8-2. Return Sync Level Adjustment ........................... 3-26
3-8-3. Return Frequency Adjustment ............................ 3-27
3-8-4. 74 MHz Clock Duty Adjustment ........................ 3-28
3-8-5. CHU Y Level Adjustment ................................... 3-28
3-8-6. CHU C Level Adjustment ...................................3-28
3-8-7. MX-109 Prompter Adjustment ............................ 3-29
3-8-8. Return DC Level Adjustment .............................. 3-31
3-9. Audio System Adjustment (HDC1550) ........................ 3-32
3-9-1. Frequency Adjustment ........................................ 3-32
3-9-2. Audio Modulation Adjustment ............................ 3-33
3-9-3. INCOM 1 Demodulation/
Output Level Adjustments .................................. 3-34
3-9-4. INCOM 2 Demodulation/
Output Level Adjustments .................................. 3-35
3-9-5. PGM 1 Demodulation/
Output Level Adjustments .................................. 3-36
3-9-6. PGM 2 Demodulation/
Output Level Adjustments .................................. 3-37
3-10. RPN Compensation ...................................................... 3-38
3-10-1. Automatic Compensation (APR) ........................ 3-38
3-10-2. Manual RPN Compensation Adjustment ............ 3-38
3-10-3. Procedures to be Taken When the RPN
Compensation Fails ............................................. 3-39
3-10-4. Performing Automatic RPN Detection
Effectively ........................................................... 3-40
3-10-5. RPN Compensation Flowchart ............................ 3-41
4. File System
4-1. File Structure .................................................................. 4-1
4-2. Operator File ................................................................... 4-2
4-3. Preset Operator File ........................................................ 4-3
4-4. Scene File ........................................................................ 4-4
4-5. Reference File ................................................................. 4-6
4-6. Lens File ......................................................................... 4-8
4-7. OHB File ....................................................................... 4-10
4-8. File Items ...................................................................... 4-12
5. Setup Menu
5-1. Entering the SERVICE Menu ......................................... 5-1
5-2. Settable Special Functions ..............................................5-2

4HDC1000/V1(E)
Purpose of this manual
This manual is the maintenance manual Volume 1 for HD Color Camera HDC1000/
1400/1500/1550/1580.
This manual describes the information items that premise the service based on the
components parts such as service overview, replacement of main parts, electrical
alignment, file system, SERVICE menu, assuming use of system and service
engineers.
Related manuals
Besides this maintenance manual Volume 1 the following manual is available for
this unit.
..
..
.HDC1000 Series Operation Manual (Supplied with HDC1000)
This manual is necessary for application and operation of HDC1000.
Part number: 3-903-903-0X
..
..
.HDC1500 Series Operation Manual
(Supplied with HDC1400/1500/1550)
This manual is necessary for application and operation of HDC1400/1500/1550.
Part number: 3-868-749-0X
..
..
.HDC1580 Operation Manual (Supplied with HDC1580)
This manual is necessary for application and operation of HDC1580.
Part number: 3-992-285-0X
..
..
.Maintenance Manual Volume 2 (Available on request)
Describes the parts list, semiconductor pin assignments, block diagrams, schemat-
ic diagrams and board layouts of HDC1000/1400/1500/1550/1580.
Part number: 9-968-213-0X
..
..
.“Semiconductor Pin Assignments”CD-ROM (Available on request)
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in Broadcast and Professional equipment.
The maintenance manual Volume 2 contains a complete list of semiconductors
and their ID Nos., and thus should be used together with the CD-ROM.
Part number: 9-968-546-06
Manual Structure

1-1
HDC1000/V1(E)
Section 1
Service Overview
1-1. Checking before Installation
1-1-1. Checking the ROM and Software Version
When connecting the peripheral equipment in the list below to HDC1000/1400/
1500/1550/1580, be sure to check that the ROM and software version on each
peripheral device is corresponding to the camera to be connected.
If the ROM and software version is lower than the specified below, be sure to
perform ROM replacement and updating the software.
If ROM replacement and updating the software are required, contact your local Sony
Sales Office/Service Center.
ROM
Peripheral equipment Board name Ref No. Rom version
MSU-700A/750 CPU-293/CPU-286 IC5, IC6/IC5, IC6 Ver. 1.30 or higher
CNU-700 AT-89 or AT-89A IC4, IC5 Ver. 3.20 or higher
CNU-500 AT-100 IC4, IC5 Ver. 2.80 or higher
RCP-720/721 MPU-79 IC10 Ver. 2.90 or higher
RCP-730/731 MPU-79 IC10 Ver. 2.90 or higher
RCP-740/741 MPU-79 IC10 Ver. 2.90 or higher
RCP-700/701 MPU-92 IC6 Ver. 2.90 or higher
RM-B150 CPU-266 IC4 Ver. 1.00 or higher
HDCU-900 AT-141 IC105, IC106 Ver. 1.40 or higher
Software
Peripheral equipment Board name Software version
RCP-750/751 MPU-123 Ver. 1.21 or higher
RM-B750 MPU-124 Ver. 1.00 or higher
HDCU1000 AT-141 Ver. 1.21 or higher
HDCU1500 AT-149 Ver. 1.00 or higher
MSU-900 CPU-396 Ver. 1.02 or higher
HDCU-950 AT-149 Ver. 1.11 or higher

1-2 HDC1000/V1(E)
1-2. Connectors and Cables
1-2-1. Connector Input/Output Signals
HDC1000 Connector Layout
!\ 24350!'!,89
7
!- !]![ 1
!;!= !=

1-3
HDC1000/V1(E)
1
0
2
3*1
5
4
6
7
8
9
!-
!. !-
!]
!,
!'
!= !=
!;
!\
*: HDC1500 only
*1: There are no connectors on HDC1580.
*2: There are no connectors on HDC1400/1550.
*
*1
*2
*
*1
*2
HDC1400/1500/1550/1580 Connector Layout

1-4 HDC1000/V1(E)
1
23
4
88
88
8RET CONTROL (6P FEMALE)
(External view)
No. Signal I/O Specifications
1 INCOM 1 IN Zi >10 kZ
MIC-ON/OFF ON : GND
OFF : OPEN
2 INCOM 2 IN Zi >10 kZ
MIC-ON/OFF ON : GND
OFF : OPEN
3GND ——
4 RET 3-ON/OFF IN Zi >10 kZ
ON : GND
OFF : OPEN
5 RET 1-ON/OFF IN Zi >10 kZ
ON : GND
OFF : OPEN
6 RET 2-ON/OFF IN Zi >10 kZ
ON : GND
OFF : OPEN
99
99
9DC OUT (4P FEMALE)
(External view)
No. Signal I/O Specifications
1 UNREG GND —— GND for POWER
2 NC No connection
3 NC No connection
4 UNREG OUT +12 V dc 500 mA (max)
Input/Output Signals
11
11
1CCU connector (HDC1000/1400/1500/1580)
BTA S-004A/005A/006A compliant 1.485 Gbps serial
HDCU/HDFX connector (HDC1550)
UC: King Triax connector
CE: Fisher Triax connector
Output Signals
22
22
2SDI 1 (HDC1000/1500)
HD SDI signal
BTA-S004A compliant
BNC type 75 Z, 0.8 V p-p 1.485 Gbps
33
33
3SDI 2 (HDC1000/1500)
SDI (HDC1400/1550)
HD SDI signal
BTA-S004A compliant
BNC type 75 Z, 1.0 V p-p
or
SD SDI signal
44
44
4TEST OUT
BNC type 75 Z, 1.0 V p-p
55
55
5PROMPTER OUT (HDC1000/1400/1500/1580)
BNC type 75 Z, 1.0 V p-p
66
66
6EARPHONE OUT (HDC1400/1500/1550/1580)
EARPHONE mini jack
77
77
7PROMPTER2 OUT (HDC1500)
BNC type 75 Z, 1.0 V p-p
Input Signals
55
55
5GENLOCK IN (HDC1400/1500/1550/1580)
BNC type 75 Z, 1.0 V p-p
(For future use)
55
55
5RET IN (HDC1400/1500/1550/1580)
BNC type 75 Z, 1.0 V p-p
(For future use)
77
77
7Not used

1-5
HDC1000/V1(E)
17
6
5
4
3
2
8
21
3
!/!/
!/!/
!/ REMOTE (8P FEMALE)
(External view)
No. Signal I/O Specifications
for RCP for TRUNK
(RS422A)
1 TX (X) TX1 (+) OUT SERIAL DATA OUT
2 TX (Y) TX1 (_) OUT /TRUNK1 DATA OUT
(for RS-422A)
3 TX (X) RX1 (+) IN SERIAL DATA IN
4 TX (Y) RX1 (_) IN /TRUNK1 DATA IN
(for RS-422A)
5 TX-GND —— GND for TX
6 POWER (+) OUT OUT UNREG +10.5 V to 17 V dc,
200 mA (max)
7 POWER (_) OUT —— GND for UNREG-OUT
8 VIDEO (X) OUT 75 Z, 1.0 V p-p
(SD Video)
CHASSIS GND —— CHASSIS GND
!-!-
!-!-
!- AUDIO IN CH1/CH2 (3P FEMALE)
(External view)
No. Signal I/O Specifications
1 AUDIO 1/2 (G) —— _60 dBu, _50 dBu, _40 dBu,
2 AUDIO 1/2 (X) IN _30 dBu, _20 dBu, selectable
3 AUDIO 1/2 (Y) IN High impedance, Balanced
(0 dBu = 0.775 Vrms)
!=!=
!=!=
!= INTERCOM 1/2 (5P FEMALE)
(External view)
No. Signal I/O Specifications
1 EXT-INCOM-T (Y) IN _20 dBu (CARBON MIC)
2 EXT-INCOM-T (X) IN _60 dBu (DYNAMIC MIC)
3 GND ——
4 EXT-INCOM- OUT 0 dBu
LEFT (X)
5 EXT-INCOM- OUT 0 dBu
RIGHT (X)
(0 dBu = 0.775 Vrms)
![![
![![
![ AC OUT (HDC1000)
(For service personnel only)
(External view) (External view)
No. Signal I/O Specifications
E GND —— CHASSIS GND
N UTL (C) OUT .AC 100/120 V, 200 VA or
below (UC, J)
L UTL (H) OUT .AC 230 V (CE)
!]!]
!]!]
!] DC IN (4P MALE)
(External view)
No. Signal I/O Specifications
1 EXT_DC (C) —— GND for DC (+)
2 NC No connection
3 NC No connection
4 EXT_DC (H) IN +10.5 to 17 V dc
UC, J CE
E
LN
LN
E

1-6 HDC1000/V1(E)
18
36
1
19
!\!\
!\!\
!\ LENS (36P FEMALE) (HDC1000)
(External view)
No. Signal I/O Specifications
23 RET 3-ON IN Zi >10 kZ
ON : GND
OFF : High impedance
24 LENS-ADR-0 IN *1
25 LENS-ADR-1 IN *1
26 LENS-ADR-2 IN *1
27 LENS-ADR-3 IN *1
28 EXT 1-ON OUT ON : GND
OFF : High impedance
29 EXT 2-ON OUT ON : GND
OFF : High impedance
30 F DEM (FAR) IN No connection
31 INCOM 1- IN Zi >10 kZ
ENG/PROD ENG : GND
PRD : High impedance
32 INCOM 2- IN Zi >10 kZ
ENG/PROD ENG : GND
PRD : High impedance
33 INCOM 1-MIC-ON IN Zi >10 kZ
ON : GND
OFF : High impedance
34 INCOM 2-MIC-ON IN Zi >10 kZ
ON : GND
OFF : High impedance
35 F-CONT-SIG OUT No connection
36 F-DEM (NEAR) IN No connection
*1 Zi >10 kZ
1 : High impedance
0 : 0 +0.5 V
_0
LENS ADRS 0 (low-order bit)
LENS ADRS 3 (high-order bit )
*2Zi > 10 kZ
1 : High impedance
0 : 0 ±0.5 V
EX1 EX2 EX3 MODE
1 1 1 EXTENDER OFF
1 0 1 EXT-1 (x1.5) ON
0 1 1 EXT-2 (x2) ON
0 0 1 EXT-3 (x2.5) ON
No. Signal I/O Specifications
1 NC No connection
2 NC No connection
3 NC No connection
4 LENS +12 V OUT +12 V (at 2 A)
5 GND (LENS) —— GND for +12 V (LENS)
6 GND (SIG) —— GND
7 NC No connection
8 LENS-EXT-1 IN *2 (LENS SERIAL DATA)
(SERIAL RXD)
9 LENS-EXT-2 IN *2
10 LENS-EXT-3 IN *2
11 LENS-SERVO OUT ON : GND
OFF : High impedance
12 IRIS-POSI IN Zi >10 kZ
2 to 7 V
“3.4 ±0.1 V (F16)”
“6.2 ±0.1 V (F2.8)”
13 ZOOM-POSI IN Zi >10 kZ
2 to 7 V
“2 V (WIDE), 7 V (TELE)”
14 RET 1-ON IN Zi >10 kZ
ON : GND
OFF : High impedance
15 RET 2-ON IN Zi >10 kZ
ON : GND
OFF : High impedance
16 FOCUS-POSI IN Zi >10 kZ
2 to 7 V
“2 V (MIN), 7 V (∞)”
17 IRIS-CONT OUT 2 to 7 V
“3.4 ±0.1 V (F16)”
“6.2 ±0.1 V (F2.8)”
Zo <1 kZ
18 IRIS-AUTO OUT AUTO : GND
/MANU MANU : High impedance
(SERIAL TXD) Zo <1 kZ
(LENS SERIAL DATA)
19 NC No connection
20 NC No connection
21 LENS R TALLY OUT ON : GND
OFF : High impedance
Zo <1 kZ
22 LENS-PUPIL-POSI IN Zi >10 kZ
1 to 4 V
1 V : _7.5d
4 V : +7.5d

1-7
HDC1000/V1(E)
EX 2 ON
30 kΩ
EX 0.8 ON
13 123456789101112
25 1415161718192021222324
!\!\
!\!\
!\ LENS (12P FEMALE) (HDC1400/1500/1550/
1580)
(External view)
No. Signal I/O Specifications
1 RET VIDEO IN ENABLE : 0 V
ENABLE DISABLE : +5 V or OPEN
2 VTR CTL IN ENABLE : 0 V
DISABLE : +5 V or OPEN
3 GND —— GND for UNREG
4 SERVO MA/AT OUT AUTO : +5 V
MANU : 0 V or OPEN
5 IRIS POSITION OUT +3.4 V (F16) to
+6.2 V (F2.8)
6 UNREG OUT +10.5 V to +17 V
7 IRIS POSITION IN +3.4 V (F16) to
+6.2 V (F2.8)
8 IRIS AT/MA OUT AUTO IRIS : 0 V
MANUAL IRIS : +5 V
9 EXTENDER IN EX 2 ON : GND
ON/OFF EX 0.8 ON : 30 kZto GND
OFF : OPEN
10 ZOOM IN WIDE : 2 V
POSITION TELE : 7 V
11 FOCUS POSI IN ∞ : 7 V
(/LENS RX) min. : 2 V
12 (LENS TX) OUT
!;!;
!;!;
!; VF (25P FEMALE) (HDC1000)
(External view)
No. Signal I/O Specifications
1 VF-Y (X) OUT 1.0 V p-p, Zo = 75 Z
2 VF-GND (Pr) —— GND for VF-Pr (X)
3 VF-Pr (X) OUT 0.7 V p-p, Zo = 75 Z
4 VF-GND (Pb) —— GND for VF-Pb (X)
5 VF-Pb (X) OUT 0.7 V p-p, Zo = 75 Z
6 PEAKING IN 0 to 5 V dc
LEVEL
7 VF-UNREG OUT +10.5 to +20 V
8 VF-UNREG
9 NC No connection
10 S-DATA IN/OUT TTL level
11 TALLY (R)-VF OUT ON : +5 V
OFF : 0 V
12 EFFECT OUT ON : +5 V
OFF : 0 V
13 NC No connection
14 VF-GND (Y) —— GND for VF-Y (X)
15 S-CK OUT TTL level
16 BATT IND OUT ON : +5 V
OFF : 0 V
17 CHASSIS GND —— GND
18 TALLY (G)-VF OUT ON : +5 V
OFF : 0 V
19 GND (UNREG) —— GND for VF-UNREG
20 GND (UNREG)
21 VF-SEL IN BW : 0 V
COLOR : +5 V
22 H EXPAND OUT ON : GND
OFF : +5 V
23 NC No connection
24 NC No connection
25 V EXPAND OUT ON : GND
OFF : +5 V

1-8 HDC1000/V1(E)
2
9
1
8
10
1211
37
64 5
!;!;
!;!;
!; VF (20P FEMALE) (HDC1400/1500/1550/1580)
(External view)
No. Signal I/O Specifications
1 S-DATA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK OUT TTL level
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY OUT ON : 5 V
OFF : GND
9 NC No connection
10 NC No connection
11 NC No connection
12 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
13 VIDEO GND —— GND for VIDEO
14 Pb VIDEO OUT ±0.35 V p-p, Zo = 75 Z
15 Pr VIDEO OUT ±0.35 V p-p, Zo = 75 Z
16 NC No connection
17 R TALLY OUT ON : 5 V
OFF : GND
18 NC No connection
19 UNREG GND —— GND for UNREG
20 UNREG OUT +10.5 V to +17 V
!'!'
!'!'
!' CRANE (12P FEMALE)
(External view)
No. Signal I/O Specifications
1 Pr VIDEO (X) OUT ±0.35 V p-p, Zo = 75 Z
2 Pb VIDEO (X) OUT ±0.35 V p-p, Zo = 75 Z
3 NC No connection
for for
RS422A RS232C
4 TX0 (+) TX1 OUT TRUNK Data out
5 TX0 (_) TX0 OUT
6 RX0 (_) RX0 IN TRUNK Data in
7 RX0 (+) RX1 IN
8 GND (VIDEO) —— GND for VIDEO
9 Y VIDEO (X) OUT 1.0 V p-p, Zo = 75 Z
10 GND —— GND for SCL/SDA
11 SCL EXT-VF OUT TTL level
12 SDA EXT-VF IN/OUT TTL level

1-9
HDC1000/V1(E)
21
3
!,!,
!,!,
!, TRACKER (10P FEMALE)
(External view)
No. Signal I/O Specifications
1 TRACKER OUT TRACKER RECEIVE/PGM
LEFT _20 dBu unbalanced
2 GND (TALK) —— GND for TRACKER TALK
3 GND (RECEIVE/ —— GND for RECEIVE/PGM/TL
PGM/TL)
4 TRACKER RIGHT OUT TRACKER RECEIVE/PGM
_20 dBu unbalanced
5 UNREG OUT +12 V (+10.5 to +17.0 V)
6 GND (UNREG) —— GND for UNREG
7 TRACKER IN TRACKER TALK
TALK (X) 0 dBu /_20 dBu
8 TRACKER IN High impedance balanced
TALK (Y)
9 G TALLY OUT ON : GND
OFF : High impedance
(Open collector)
10 R TALLY OUT ON : GND
OFF : High impedance
(Open collector)
(0 dBu = 0.775 Vrms)
!.!.
!.!.
!. MIC 1 IN (3P FEMALE) (HDC1400/1500/1550/
1580)
(External view)
No. Signal I/O Specifications
1 MIC 1 (G) —— _60 dBu, _50 dBu, _40 dBu,
2 MIC 1 (X) IN _30 dBu, _20 dBu, selectable
3 MIC 1 (Y) IN High impedance, Balanced
(0 dBu = 0.755 Vrms)
81
54
10 9 27
63
1-2-2. Wiring Diagrams for Cables
CCA-5 Cable
BrownBrown
Brown
Red
Red
White
White
White
Orange
Black
—8P CONNECTOR (MALE) —
(WIRING SIDE)

1-10 HDC1000/V1(E)
1-2-3. Connection Connectors/Cables
Connection made with the connector panels during instal-
lation or service, should be made with the connectors/
complete cable assemblies specified in the following list,
or equivalent parts.
Indication Connection connector/cable
TEST OUT 1-569-370-12 Plug, BNC
PROMPTER OUT
SDI 1/2
(BNC)
AUDIO IN CH1/CH2 1-508-084-00 XLR, 3P Male or
MIC 1 IN ITT Cannon XLR-3-12C equivalent
(3P FEMALE)
RET CONTROL 1-560-078-00 Plug, 6P Male or
(6P FEMALE) HIROSE HR10-7PA-6P equivalent
DC OUT 1-566-425-11 Plug, 4P Male or
(4P FEMALE) HIROSE HR10A-7P-4P equivalent
INTERCOM 1/2 1-508-370-11 XLR, 5P Male or
(5P FEMALE) ITT Cannon XLR-5-12C equivalent
DC IN 1-508-362-00 XLR, 4P Female or
(4P MALE) ITT Cannon XLR-4-11C equivalent, or
Cable assembly 1-551-577-00
(Supplied with AC-550/550CE)
CRANE 1-819-261-11 Connector,
(12P FEMALE) Round Type 12P
REMOTE .1-766-848-11 Plug, 8P Male or
(8P FEMALE) CCA-5 cable assembly
(CCA-5-10 (10 m) /CCA-5-3 (3 m))
(option) *2 *3
.REMOTE cable 1-783-372-11
(supplied with RM-B150, 10 m) *1 *2 *3
TRACKER 1-506-522-12 Connector,
(10P FEMALE) Round Type 10P
*1: Use of REMOTE cable enables to monitor video signals. (The pin 8 is
available for the video signal line.)
The down-converted SD signal is output.
*2: If using a cable of length different from a standard product, contact your
local Sony Sales Office/Service Center.
n
*3: The pin 8 of CCA-5 cable is GND (ground).
The pin 8 of REMOTE cable is not GND (ground).
1-2-4. Note in Connecting CCU Connector
(HDC1000/1400/1500/1580)
It is recommendable to clean the optical contact portions
mentioned below before connecting this unit to the camera
control unit.
.CCU connector of this unit
.Camera connector of the camera control unit
.Optical/Electrical cable
For details on a cleaning method, refer to Section 1-8
“Cleaning of Connector/Cable”.

1-11
HDC1000/V1(E)
PA-317
CN-2579
TG-243
DR-528
BI-175
BI-175
CN-2578
BI-175
SWITCHING REGULATOR
DC-DC COVERTER
CN-2602
SDI-84 DPR-265
SW-1233
AT-166
CN-2603 (for UCJ)
CN-2603B (for CE)
CN-2608
CN-2671
CN-2671
CN-2609 LE-291
LE-309
CN-2604
CN-2605
CN-2606
CN-2607
MB-1060
VDA-63
DAP-33
AU-298
AT-163
1-3. Location of Printed Circuit Boards
HDC1000

1-12 HDC1000/V1(E)
PA-317 (HDC1400/1500)
PA-317C (HDC1580)
CN-2579
TG-243 (HDC1500)
TG-243B (HDC1400)
TG-243C (HDC1580)
DR-528
BI-175
BI-175
BI-175
CN-2578
HDC1400/1500/1580
DC-DC COVERTER
SWITCHING REGULATOR
AT-163
AU-298
DAP-33
VDA-63
MB-1059
SW-1245
SW-1240
SW-1239
SW-1238
SW-1236
SW-1273
SW-1242
SW-1241 (HDC1400, HDC1500 (SY))
SW-1241B (HDC1500 (CE)/HDC1580)
SW-1237
SDI-84 (HDC1500)
SDI-84C (HDC1400/1580)
LE-308
CN-2616
CN-2615
CN-2614B
CN-2617
CN-2618
CN-2622
CN-2620
CN-2640
CN-2623
CN-2619
CN-2621
CN-2618
DPR-265 (HDC1400/1500)
DPR-265C (HDC1580)