AudioBahn AVDVD07N User manual

UNIVERSAL MOUNT DVD PLAYER
WITH REMOTE CONTROL
AVDVD07N
OPERATING INTSTRUCTIONS
PLEASE RETAIN MANUAL FOR FUTURE USE AND REFERENCE
QUALITY, RELIABILITY, & PURE BLISS

INTRODUCTION
UNIT INTRODUCTION
FEATURES AND SAFETY
DISC INFORMAION
THE PLAYER
3
4
5
7-8
9-10
INSTALLATION 11-13
ELECTRICAL CONNECTION 14
REMOTE CONTROL 15-17
WARNING / DISCLAIMER 34
WARRANTY 35-36
SAFETY 6
Table of Contents
Table of Contents
2
GENERAL OPERATION 18-19
ADVANCED OPERATION 20-26
SETUP 27-31
TROUBLESHOOTING 32
SPECIFICATIONS 33

Unit Introduction

Digital Audio Out-Coaxial
DVD Player
Multi-subtitle Languages Function
Multi-audio Languages Function
Multi-angle Function
Parental Control
Remote Control

Features and Safety
5
Features
Compatible with PAL DVD (Video CD)
and NTSC DVD (Video CD)
This player can play discs recorded in either
PAL or NTSC format.
A single LSI chip now integrates all
major DVD playback circuit functions
including MPEG2 decoder, video D/A
converter, and audio decoders.
L/R stereo analog audio outputs for
connection to existing head unit aux
inputs. Video output is composite video.
Supplied remote handles multi-function
software (multi-language
audio-track/subtitle, multi-angle,
multi-story, etc.), plus all basic functions.
Use This Product Safely
Do not expose the product to water or
excessive moisture. This could cause
electrical shorts, fire or other damage.
When Driving
Keep the volume level low enough to be
aware of road and traffic conditions.
When Parked
Parking in direct sunlight can produce very
high temperatures inside your vehicle. Give
the interior a chance to cool down before
starting playback.
Use the Proper Power Supply
This product is designed to operate with a
12 volt DC, negative ground battery system
(the regular system in a North American
car).
Protect the Disc Mechanism
Avoid inserting any foreign objects into the
slot of this player.
Failure to observe this may cause
malfunction due to the precise mechanism
of this unit.
Use Authorized Service Centers
Do not attempt to disassemble or adjust this
precision product. Please refer to the
Service Center list included with this
product for service assistance.
For Installation
The unit should be installed in a horizontal
position with the front end up at a
convenient angle, but not more than 300.

Safety

#!54)/.
-/"),%$6$0,!9%2)3!#,!33)
,!3%202/$5#4(/7%6%24()3
-/"),%$6$0,!9%253%3!
6)3)",%).6)3)",%,!3%2"%!-
7()#(#/5,$#!53%(!:!2$/53
2!$)!4)/.%80/352%)&$)2%#4%$
"%352%4//0%2!4%4(%-/"),%
$6$0,!9%2#/22%#4,9!3
).3425#4%$
53%/&#/.42/,3/2!$*534-%.43
/20%2&/2-!.#%/&02/#%$52%3
/4(%24(!.4(/3%30%#)&)%$
(%2%).-!92%35,4).(!:!2$/53
2!$)!4)/.%80/352%
$/./4/0%.#/6%23!.$$/./4
2%0!)29/523%,&2%&%23%26)#).'
4/15!,)&)%$0%23/..%,
7!2.).'
4/2%$5#%4(%2)3+/&&)2%/2
%,%#42)#3(/#+$/./4
%80/3%4()3%15)0-%.44/2!).
/2-/)3452%
4/2%$5#%4(%2)3+/&&)2%/2
%,%#42)#3(/#+!.$
!../9).').4%2&%2%.#%53%
/.,94(%2%#/--%.$%$
!##%33/2)%3
4()3$%6)#%)3).4%.$%$&/2
#/.4).5/53/0%2!4)/.
4HISPRODUCTINCORPORATESCOPYRIGHT
PROTECTIONTECHNOLOGYTHATISPROTECTEDBY
METHODCLAIMSOFCERTAIN53PATENTSAND
OTHERINTELLECTUALPROPERTYRIGHTSOWNEDBY
-ACROVISION#ORPORATIONANDOTHERRIGHTS
OWNERS5SEOFTHISCOPYRIGHTPROTECTION 
TECHNOLOGYMUSTBEAUTHORIZEDBY
-ACROVISION#ORPORATIONANDISINTENDED
FORHOMEANDOTHERLIMITEDVIEWINGUSES
ONLYUNLESSOTHERWISEAUTHORIZEDBY
-ACROVISION#ORPORATION2EVERSE
ENGINEERINGORDISASSEMBLYISPROHIBITED
2EGION-ANAGEMENT)NFORMATION
2EGION-ANAGEMENT)NFORMATION4HIS
-OBILE$6$0LAYERISDESIGNEDAND
MANUFACTUREDTORESPONDTOTHE2EGION
-ANAGEMENT)NFORMATIONTHATISRECORDED
ONA$6$DISC)FTHE2EGIONNUMBER
DESCRIBEDONTHE$6$DISCDOESNOT
CORRESPONDTOTHE2EGIONNUMBEROFTHIS
-OBILE$6$0LAYERTHIS-OBILE$6$
0LAYERCANNOTPLAYTHISDISC

Disc Information
$ISCFORMATSSUPPORTEDBYTHIS
PLAYER
$6$
CMDISC
Y
6IDEO#$ 
CMDISC
#$
CMDISC
-0
CMDISC
(ANDLINGAND#LEANING
$IRTDUSTSCRATCHESANDWARPINGDISCS
WILLCAUSEMISOPERATION
$ONOTPLACESTICKERSORMAKE
SCRATCHESONDISCS
$ONOTWARPDISCS
!DISCSHOULDALWAYSBEKEPTINITS
CASEWHENNOTINUSETOPREVENTFROM
DAMAGE
$ONOTPLACEDISCSINTHEFOLLOWING
PLACES
 $IRECTSUNLIGHT
 $IRTYDUSTYANDDAMPAREAS
 .EARCARHEATERS
/NTHESEATSORDASHBOARD
$ISC#LEANING 
5SEADRYSOFTCLOTHTOWIPETHESURFACE)F
THEDISCISQUITEDIRTYUSEASOFTCLOTH
SLIGHTLYMOISTUREDWITHISOPROPYLRUBBING
ALCOHOL.EVERUSESOLVENTSSUCHAS
BENZINETHINNERORCONVENTIONALRECORD
CLEANERSASTHEYMAYMARTHESURFACEOF
THEDISC
.OTE
!DISCMAYBECOMESOMEWHATSCRATCHED
ALTHOUGHNOTENOUGHTOMAKEITUNUSABLE
DEPENDINGONTHEWAYITISHANDLEDAND
CONDITIONSINTHEUSAGEENVIRONMENT.OTE
THESESCRATCHESARENOTANINDICATIONOF
ANYPROBLEMWITHTHEPLAYER
,ABLESIDEUP
$ONOTTOUCH
THEUNDERSIDE
OFTHEDISC
$ONOTBEND
7IPETHEDISCFROMCENTER
TOWARDTHEOUTSIDEEDGE
4-

Disc Information
2OUGHSPOTSON
ONINSIDEEDGE
ORPENCIL
2OUGHSPOTS
OUTSIDEEDGE
"ALLPOINTPEN
0REPARING.EW$ISCSWITH
2OUGH3POTS
!NEWDISCMAYHAVEROUGHEDGESONITS
INSIDEANDOUTSIDEEDGES)FADISCWITH
ROUGHEDGESISUSEDTHEPROPERSETTING
WILLNOTBEPERFORMEDANDTHEPLAYER
WILLNOTPLAYTHEDISC4HEREFORE
REMOVETHEROUGHEDGESINADVANCEBY
USINGABALLPOINTPENORPENCILAS
SHOWNONTHERIGHT4OREMOVETHE
ROUGHEDGESPRESSTHESIDEOFTHEPENOR
PENCILAGAINSTTHEINSIDEANDOUTSIDE
EDGESOFTHEDISC

The Player
9
FRONT VIEW
1. PWR ( )
2. EJ ( )
3. SETUP
4. AUDIO
5. SOURCE
6. Disc Slot
7. PLAY/PAUSE( )
8. STOP ( )
9. PREV ( )
10. NEXT ( )
11. VOLUME
12. VOLUME
13. /,/cursor buttons
14. ENTER
15. Indicator Light for DVD
16. Indicator Light for AV
17. Indicator Light for STAND BY
18. VIDEO IN
19. AUDIO IN L
20. AUDIO IN R
21. IR
22. Reset button
17612 15 16
11
2
17 21
22
8
3
95
13 1814 19 20
10
4

The Player
10
BACK VIEW
23. DC 12V INPUT Socket
24. DC 12V OUTPUT Socket
25. AV OUTPUT TYPE Switch
26. DIGITAL AUDIO
27. REMOTE Socket
28. S-VIDEO Socket
29. AUDIO/VIDEO OUTPUT 1
30. AUDIO/VIDEO OUTPUT 2
!.4).
23 24 25 26 27 28 30

Installation
Notes:
Choose the mounting location where the
unit will not interfere with the normal
driving function of the driver.
Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.
Use only the parts included with the
unit to ensure proper installation. The
use of unauthorized parts can cause
malfunctions.
Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop, like
an emergency stop.
If installation angel exceeds 30 from
horizontal, the unit might not give its
optimum performance.
Avoid installing the unit where it would
be subject to high temperature, such as
from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front”(conventional DIN
Front-mount) or “Rear”(DIN Rear-mount
installation, utilizing threaded screw holes at
the sides of the unit chassis). For details,
refer to the following illustrated installation
methods.
TAKE OUT SCREW BEFORE INSTALLATION
Before install the unit, please remove the
two screws.
DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be instal led in any dashboard
having an opening as shown below:
Installing the unit
Be sure you test all connections first, and
then follow these steps to install the unit.
1. Make sure the ignition is turned off, and
then disconnect the cable from the
vehicle battery’s negative (-) terminal.
2. Disconnect the wire harness and the
antenna.
3. Lift the top of the outer trim ring then
pull it out to remove it.
4. The two supplied keys release tabs
inside the unit’s sleeve so you can
remove it. One key is for the right side
and the other is for the left side. Insert
the keys as far as they will go (with the
notches facing up) in to the appropriate
slots at the middle left and right sides of
the unit. Then slide the sleeve off the
back of the unit.

53mm
182mm
Take out screw
before installation.

Installation
5. Mount the sleeve by inserting the sleeve
into the opening of the dashboard and
bend open the tabs located around the
sleeve with a screwdriver. Not all tabs
will be able to make contact, so examine
which ones will be most effective.
Bending open the appropriate tabs
behind the dashboard to secure the
sleeve in place.
Tabs
Screwdriver
Sleeve
Dashboard
6. Reconnect the wire harness and the
antenna and be careful not to pinch any
wires or cables.
7. Slide the unit into the sleeve until it
locks into place.
8. To further secure the unit, use the
supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap to
the mounting bolt on the back of the unit.
If necessary, bend the metal strap to fit
your vehicle’s mounting area. Then use
the supplied hardware (Tapping Screw
(5x25mm) and Plain Washer) to attach the
other end of metal strap to a solid metal
part of the vehicle under the dashboard.
This strap also helps ensure proper
electrical grounding of the unit.
Mounting Bolt
Plain Washer
Tapping Screw
Metal Strap
Spring Washer Hex Nut
9. Reconnect the cable to the vehicle
battery’s negative (-) terminal. Then
replace the outer trim ring.
Removing the unit
1. Make sure the ignition is turned off, then
disconnect the cable from the vehicle
battery’s negative (-) terminal.
2. Remove the metal strap attached the back
of the unit (if attached).
3. Lift the top of the outer trim ring then pull
it out to remove it.
4. Insert both of the supplied keys into the
slots at the middle left and right sides of
the unit, then pull the unit out of the
dashboard.
Outer Trim Ring
L Key
Sleeve
R Key

Installation
DIN REAR-MOUNT (Method B)
If your vehicle is a Nissan, Toyota or Suzuki,
follow these mounting instructions.
Use the screw holes marked T (Toyota), N
(Nissan) or S (Suzuki) located on both sides
of the unit to fasten the unit to the factory
radio mounting brackets supplied with your
vehicle.
Dashboard or Console
Screw
Hook
Factory Radio
Mounting Bracket
Side View showing
Screw Holes marked
T, N or S
Screw
To fasten the unit to the factory radio
mounting brackets.
1. Use a screwdriver to loose the hook’s
screws on the front left and right sides of
the unit and remove the hooks.
2. Align the screw holes on the bracket
with the screw holes on the unit, and
then tighten the screws on each side.
3. Fasten with the supplied truss screws
(5x5mm) or flush surface screws
(4x5mm), depending on the shape of the
screw holes in the bracket.
Note: the outer trim ring, sleeve and the
metal strap are not used for method B
installation.

Electrical Connection
14
Note:
The S-VIDEO output is only effective on DVD, not effective on AV source. That is to say,
the video signal of AV input source can’t be output from the S-VIDEO jack.
Slide AV OUTPUT TYPE switch on the back of the unit left or right to select A or B.
When the switch is slid to Bside, the AV INPUT signal is directly outputted from AV1
OUTPUT and it is out of control of any buttons.
When the switch is slid to Aside, the AV OUTPUT signal is under control of MODE button
or SOURCE.
YELLOW
YELLOW
RED
RED
WHITE
WHITE
VIDEO 2 OUT
VIDEO 1 OUT
AUDIO 2 R OUT
AUDIO 1 R OUT
AUDIO 2 L OUT
AUDIO 1 L OUT
DIGITAL AUDIO
(OPTIONAL)
(OPTIONAL)
REMOTE CONTROL RECEIVER
CIGARETTE LIGHTER
AC/DC
ADAPTO
(OPTIONAL)
36)$%/
$)')4!,
!5$)/
$#6
!6/54054
490%
"!
).054 /540 54
!6
!6
2%-/4%
!5$)/6)$%//540 54

Remote Control
15
LOCATION AND FUNCTION OF KEYS
24 27
15
3
8
32
26
9
25
428
1031
7
30
26
12
3
29
15
11
18
13
19
23
17
20
16
14
22
21

Remote Control
16
1. POWER Press POWER to turn the unit ON or OFF.
2. MUTE Press to mute the sound.
3. SUB-T Changing of the SUBTITLE language on multi-subtitle language DVD disc.
4. ANGLE Changing of the view angle on multi-angle DVD disc.
5. CONSOLE Display statistical disc information during playback.
6. MODE Changing between DVD mode and AV mode.
7.SETUP DisplaytheSETUPmenu.
8. P/N Switch between PAL mode and NTSC mode.
9. AUDIO Changing of the AUDIO soundtrack on multi-audio soundtrack DVD disc.
ChangingofthesoundmodeoftheVCD/CDdiscs.
10. TITLE Display the TITLE menu that is stored in DVD disc.
11.MENU Displaytheadjustmentitems,suchasBright,Contrast,Color,Tint,Screen.
12. / , / Insomemenus, / , / buttons served as cursor buttons to select item
left/right, ahead/back.
13. OK Confirm the Track/Chapter selected with the numeric buttons or selected with
the cursor buttons on TV screen.
14. /Changing for slow forward/ reverse playback motion.
15. Presstoplaythedisc.
16. /Press to search forward rapidly & to search reverse rapidly.
17. /Press to skip to the next track & press to skip back one track.
18. Pressittostopplayback.
19. Press it for the first time to pause playback. Press it again to stop at the next
picture (step function for DVD/VCD/SVCD).
20.0-9 Numericbuttons
21. 3D During disc playback, press it to select normal or 3D surround effect mode.
22. CLEAR When you input a number in error, press the button to clear it.
23. VOLUME+/- Press VOLUME+/- button to increase or decrease the volume level. (Only in
DVD mode)
24. ZOOM Allows the picture to be increased in size.
25. BOOKMK During playback, press to enter bookmark function.
26. GOTO Press to select the bookmark that you set.
27. PBC Changing between PBC ON and PBC OFF on the VCD disc.
28. RANDOM Allows the track played in random order.
29. PROGRAM Allows the track played in the order you programmed.
30. REPEAT Switch the Repeat mode of discs.
31. A-B A-B repeat allows a passage to be repeated continuously..
32. EJECT Press to eject the disc.

Remote Control
17
Preparing the Remote Control
Inserting the Batteries
1. Open the battery compartment cover.
2. Insert the new battery. Make sure that the
positive and negative terminals of the
battery are oriented as indicated.
3. Close the cover.
Battery: one button cell lithium battery
Using the Remote Control
Face the remote control towards the player
front face IR mark (remote control signal
receiver).
Operation angle: About 30 degree in each
the direction of the front of the IR mark.

General Operation
18
TURN THE UNIT ON
After all connections are completed
correctly, press the (PWR) button on the
front panel or (POWER) on the remote
control to turn on the power. When the unit
is on, it will search the disc automatically. If
there is a disc in the disc slot, the unit will
start playback automatically. Besides this,
you should turn on the monitor that
connected to the player.
Standby State
1) When the unit is on, press (PWR)
on the front panel or (POWER)on
the remote control to turn the unit off
temporarily, in order to stop the
playback in a short time and the unit
goes into standby state.
2) In standby state, press (PWR) on the
front panel or (POWER) on the
remote control again to recall playback.
And for disc playback, it can realize
memory play function.
Note: The unit has screen saver function
(select “ON” in Screen Saver setup). If the
playback is stopped and there is not any
button operation in 5 minutes, it will activate
the screen saver function automatically;
when any button for DVD function is
pressed, the screen saver function will
release automatically.
Remote Sensor (IR)
Point the remote handset to the remote
sensor IR on the front panel. Receive the
signal from the remote handset.
Loading a Disc
1. Insert the disc with printed side facing up
into the disc slot.
2. The player will start playback
automatically.
Disc Slot Eject Button
Ejecting a Disc
Press (EJ) button on the front panel or on
the remote control to eject the disc.
BASIC PLAY
Stopping Playback
- Briefly press (Stop) button to
pre-stop the unit playback. When
button on the front panel or (Play)
button on the remote control is pressed,
normal playback will continue.
- Press (Stop) button twice to stop the
playback and go back to the DVD
LOGO.
Pausing Play/Step Play
Pressing on the remote control for the
first time or pressing on the front panel
during playback will stop playback
temporarily. To return to normal playback,
press on the remote control or on
the front panel.
If you play a DVD/VCD/SVCD, press on
the remote control again to stop at the next
picture (step function). If you play a
CD/MP3/Picture CD, pressing on the
remote control again is ineffective.
Rapid Forward / Rapid Reverse
Press & during playback.
Each time the button is pressed, the speed of
rapid forward /reverse changes according to
the disc as follows.

General Operation
19
DVD:
Normal playback X2 X4 X16 X100
VCD/CD/MP3:
Normalplayback X2 X4 X8
Slow Motion Playback (For DVD Only)
Press /during play.
Each time the button is pressed, the speed of
slow forward /reverse changes according to
the disc as follows.
DVD:
X1/32 X1/16 X1/8 X1/4 X1/2
In slow motion state, press on the
remote control to recover normal playback.
Skipping Track
Press /buttons on the remote control
or on the front panel during playback.
Press to skip to the next track, and
press to skip to the previous track.
Note: For some VCD2.0 discs
(PBC-playback control), /buttons
may be unavailable.
Mute
Press MUTE button to mute the sound, but
the disc continues playing. Press MUTE
again or press volume up/down buttons on
the front panel or on the remote control,
sound will resume.
Volume Level Adjustment
In DVD mode, press /on the front
panel or VOLUME +/- on the remote
control to increase or decrease the volume
level.
DVD VIDEO MENU PLAY
When playing a DVD disc in the DVD player:
1) The disc will be played automatically
and stop at menu picture.
2) Use / , / cursor buttons to move
between the highlight bars in the menu.
3) Press ENTER button or OK button to
confirm the selected item.
MODE SELECTION
Press SOURCE button on the front panel of
the unit or MODE button on the remote
control to select among DVD and AV mode.
When select one mode, the corresponding
indicator on the front panel will be
illuminated.
RESET FUNCTION
Reset button is placed on the front panel and
must be activated with either a ballpoint pen
or thin metal object. The reset button is to be
activated for the following reasons:
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
LAST PLAY MEMORY
During disc playback, if you press
button to turn off the unit and then press
the button again to turn on the unit, the
DVD unit will resume playing from the
point that just interrupted.
During disc playback, press button to
eject the disc then load the disc into the
slot again, the unit will resume playing
from the point that just interrupted.
During disc playback, if you press
SOURCE button or MODE button to
switch to AV mode, then return to DVD
mode again, the unit will resume
playing from the point that just
interrupted.