Audiovox Electronics Pursuit PRO9056C User manual

128-8790b
1 of 2
1
Single Channel Remote Car Starter
Model PRO9056C
Owner’sManual
FEATURES :
2 Programmable RF Transmitters
Single Channel Receiver (capable of accepting 4 transmitters)
External Superheterodyne Receiver Antenna w/PushButton Switch &
LED
On-Board Start Relay
On-Board Accessory Relay
On-Board Ignition 1 Relay
On-Board Ignition 2 Relay
Ignition 2 Relay Selectable On or Off During Cranking
On-Board Parking Light Relay
Ignition 3 / Shock By-Pass / GM VAT Output (relay required)
Tach Signal Learning Circuit
Two ( + ) and Two ( - ) Safety Shutdown Circuits
Alarm By-Pass Output
AccessoryOutputs
(PulseBefore&AfterStart,DuringCrankandAfterShutDown)
Selectable Steady or Flashing Parking Lights for Run Indication
Selectable 5, 10, 15, 20, 45 and 60 Minute Run Time
Car Finder Mode
Optional Door Unlock Feature For Vehicles Equipped With Power Doors
(Only operational while running under control of the remote start unit.)
Rev A: Add new URL 11/4/2011
Rev B: New Format 5/2013
PATENTED: www.voxxintl.com/company/patents

128-8790b
2 of 2
2
REMOTESTARTINGTHEVEHICLE
This will not start the vehicle if any one of the following situations exists:
The vehicle's hood lid is opened.
The gear shift selector is not in Park.
The brake pedal is depressed.
The safety control switch is in the Off position.
1) To start the vehicle, press and release the transmitter button two
times within 2 seconds. The vehicle will start and remain running for
the pre-programmed 5,10,15,20 minute run cycle. As a visual indica-
tion, the parking lights will flash or remain on depending on the
setting by your installation center.
2) When you arrive at the vehicle, turn the ignition key to the ON
position (not the spring loaded start position), then step on the brake
pedal to disengage the remote starter. The vehicle will continue to run, but now
on its own power.
NOTE: The engine will stop running before the pre-programmed run cycle has
expired if you perform any one of the following functions:
-Press and the button on the keychain transmitter two times within 2 seconds
-Depress the brake pedal
-Open the vehicle's hood
-Place the unit in the safety control disabled mode.
PUSHBUTTONLEDRECEIVERVALET/OVERRIDE/SAFETYCONTROLSWITCH
The Pushbutton LED switch located in the receiver allows you to temporarily
disable the remote starting function of the system. This recommended whenever
the vehicle is being serviced. To place the system in the service mode:
1) With the system disarmed/unlocked, and the ignition switch off, press and
hold the Pushbutton, found on the windsheild receiver, in.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED begins to flash two short flashes followed by one long flashes and
continues this pattern until returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start is
in the service mode and will not start from RF or any other input Posse or
otherwise.
To Exit R/S Override Mode
1) With the system disarmed, Press and Hold the Push-Button, found on the
windshield receiver, in.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED turns off indicating that the R/S unit is fully functional once again.

128-8790b
3 of 2
3
UNLOCKINGTHEVEHICLE:
If you have electric door lock and the Optional Unlock feature was added, with
the vehicle running under command of the remote start unit, press and hold
the transmitter button for 3 seconds until the doors unlock.
CARFINDERMODE:
Anytime the vehicle is not running under control of the remote start unit, within
operating range of the vehicle, press and hold the pushbutton of the hand
held transmitter for 4 seconds to activate the car finder mode. The vehicle
lights will flash for 30 seconds or until the pushbutton is again pressed and
released.
TELEMATICUPGRADE:
This system has the ability to have a telematic upgrade module connected to it.
This is an upgrade that can give you control of certain functions of your vehicle
from a Telephone, or in some cases a computer interface. Please check with
yourinstallation centerfor mostrecentTelematic Upgrades.If youhad aTelematic
Upgrade installed, the manual supplied with the upgrade unit will provide an
operator's manual advising of the features of the system and means available
to control these features of your vehicle.
PROGRAMMINGNEWORREPLACEMENTTRANSMITTERS(BANK 1)
Transmitter Model Name Is Found On Back Of Transmitter Case
1) Turn the ignition key to the on position.
2) Press and release the valet/programming switch 3 times. (Siren Chirps)
3) Press the Lock Button of each transmitter you want programmed until you
hear a chirp from the horn or siren.
4) Turn the ignition switch off.
The above action programs the Lock, Unlock, Start/Trunk, and Option 1 buttons
which are typical for most systems.
For additional channel programming beyond the 1 option button, you can use
any unused button or combination of buttons not in use.
In other words, to access option channel 5, 6, 7, you would do the following:
From step 3 above:
a) Press and release the valet/programming button 4 additional times to get to
channel 5, then Press any unused transmitter button or button combination to
program.
b) From a, press and release the valet/programming button 1 time to get to
channel 6, then press any unused transmitter button or button combination to
program.

128-8790b
4 of 2
4
To purchase replacement transmitters
or to get additional product information go to:
www.pursuitcarsecurity.com
c) From b, press and release the valet/programming button 1 time to get to
channel 7, then press any unused transmitter button or button combination to
program.
NOTE: Not all systems have channels above 3, check with your installation center
for options your system may or may not have.
NOTE: Certainsystems have theability toutilize channels6 and7 fordriver priority
programming. For driver priority, the vehicle must be equipped with this feature,
and the optional feature must be set up and installed by your installation center.
Once this feature is added when the unlock button of transmitter 1 is used, it will
set driver 1 priority and when the unlock button of transmitter 2 is used it will set
driver 2 priority. In this situation, the unlock button can be programmed into two
receiver channels, unlock, channel 2 and driver priority 6 or 7. In no other circum-
stance will the system allow a transmitter button to be programmed into 2 re-
ceiver channels at the same time.
FUNCTIONSETTINGCHART
To be completed by installer
Run Time 5 Min 10 Min 15 Min 20 Min 
While Running Unlock Yes No 
Lights Pulse Steady 
© 2013 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-8790b