Ultra Start 72 Series User manual

REV.2008.06.18
TM
72 SERIES
Advanced Remote Starters &
Vehicle Security Systems
OWNER’S MANUAL
TM
FCC ID NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2.This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate
this devise.
www.ultrastarters.com
FOR USE ON AUTOMATIC TRANSMISSION
VEHICLES ONLY

PAGE 2
72 SERIES
OWNER'S MANUAL
TABLE OF CONTENTS
Important Notes.......................................................................Page 3
Quick View Operations...........................................................Pages 4-5
Remote Start Operations........................................................Pages 6-12
Remote Start Key Takeover Remote Shutdown
Idle Mode extended Runtime Turbo Timer Mode
Remote Start Optional Operations.........................................Pages 6-11
Lock Doors Unlock Doors Trunk Release
Auxiliary Outputs Panic Mode Silent Lock/Unlock
Car Finder Mode
Emergency Override Mode.....................................................Page 12
Activate Override Mode Deactivate Override Mode
Timer Mode/ Cold Start...........................................................Page 13
Transmitter Programming.......................................................Page 14
LED 2way Operations..............................................................Page 15-16
Lock 2way Unlock 2way Trunk Release 2way
Panic Mode Cold Start Low Battery Indication
Trouble Shooting.....................................................................Page 17
Diagnostics..............................................................................Page 18
Warranty...................................................................................Page 19
Other.........................................................................................Page 20
PAGE 3
72 SERIES
OWNER'S MANUAL
IMPORTANT NOTES
ATTENTION
Please take a moment to review the safety precautions before
operating your system.
1) For safety reasons, the owner/user of this system MUST INSTALL
a CARBON MONOXIDE DETECTOR in the living area near to where
the vehicle is being stored or parked.
2) It is the sole responsibility of the owner/user to keep the remote
transmitters away from the reach of children and handle with care
so that the system does not unintentionally start.
3) When the vehicle is parked in an enclosed/partially enclosed area
(ex: garage, car port...), being serviced (ex: oil change) or the
vehicle is loaned to an operator not familiar with a remote starter,
the system MUST BE placed Service Mode.
NEVER REMOTE START THE SYSTEM IN AN ENCLOSED/
PARTIALLY ENCLOSED AREA!
4) MANUAL TRANSMISSION STARTERS Never install a automatic
remote start module into a manual transmission vehicle. Doing so
could result in EXTENSIVE DAMAGE TO YOUR VEHICLE,
PROPERTY DAMAGE AND POSSIBLY CAUSE SERIOUS INJURIES
OR EVEN DEATH. IF THIS SYSTEM WAS INSTALLED IN A MANUAL
TRANSMISSION VEHICLE, RETURN TO YOUR DEALER AND HAVE
IT DISABLED UNTIL THE CORRECT MODEL CAN BE INSTALLED.
5)

PAGE 2
72 SERIES
OWNER'S MANUAL
TABLE OF CONTENTS
Important Notes.......................................................................Page 3
Quick View Operations...........................................................Pages 4-5
Remote Start Operations........................................................Pages 6-12
Remote Start Key Takeover Remote Shutdown
Idle Mode extended Runtime Turbo Timer Mode
Remote Start Optional Operations.........................................Pages 6-11
Lock Doors Unlock Doors Trunk Release
Auxiliary Outputs Panic Mode Silent Lock/Unlock
Car Finder Mode
Emergency Override Mode.....................................................Page 12
Activate Override Mode Deactivate Override Mode
Timer Mode/ Cold Start...........................................................Page 13
Transmitter Programming.......................................................Page 14
LED 2way Operations..............................................................Page 15-16
Lock 2way Unlock 2way Trunk Release 2way
Panic Mode Cold Start Low Battery Indication
Trouble Shooting.....................................................................Page 17
Diagnostics..............................................................................Page 18
Warranty...................................................................................Page 19
Other.........................................................................................Page 20
PAGE 3
72 SERIES
OWNER'S MANUAL
IMPORTANT NOTES
ATTENTION
Please take a moment to review the safety precautions before
operating your system.
1) For safety reasons, the owner/user of this system MUST INSTALL
a CARBON MONOXIDE DETECTOR in the living area near to where
the vehicle is being stored or parked.
2) It is the sole responsibility of the owner/user to keep the remote
transmitters away from the reach of children and handle with care
so that the system does not unintentionally start.
3) When the vehicle is parked in an enclosed/partially enclosed area
(ex: garage, car port...), being serviced (ex: oil change) or the
vehicle is loaned to an operator not familiar with a remote starter,
the system MUST BE placed Service Mode.
NEVER REMOTE START THE SYSTEM IN AN ENCLOSED/
PARTIALLY ENCLOSED AREA!
4) MANUAL TRANSMISSION STARTERS Never install a automatic
remote start module into a manual transmission vehicle. Doing so
could result in EXTENSIVE DAMAGE TO YOUR VEHICLE,
PROPERTY DAMAGE AND POSSIBLY CAUSE SERIOUS INJURIES
OR EVEN DEATH. IF THIS SYSTEM WAS INSTALLED IN A MANUAL
TRANSMISSION VEHICLE, RETURN TO YOUR DEALER AND HAVE
IT DISABLED UNTIL THE CORRECT MODEL CAN BE INSTALLED.
5)

1 SECOND 1 LOCK DOORS
3 SECONDS 1ACTIVATE PANIC MODE
PRESS THEN
RELEASE THEN
PRESS & HOLD
1 ACTIVATE CONSTANT LOCK OUTPUT
LOCK
BUTTON PRESS HONKS /
FLASH SYSTEM FUNCTION
BUTTON
1 SECOND 2UNLOCK DOORS
1 SECOND
WHILE ALARM IS
TRIGGERED
NONE TURNS OFF PANIC BUT DOOR STAY
LOCKED
UNLOCK/
TRUNK
PRESS & RELEASE 1 ACTIVATES REMOTE STARTER
PRESS AND HOLD
HOLD FOR 3 SEC
2
ON
AUXILIARY #1 OUTPUT (DEFAULT)
CAR FINDER (PROGRAMMABLE)
PRESS TOGETHER
THEN RELEASE
PRESS TOGETHER
THEN RELEASE
1
2
ACTIVATES SILENT LOCK WITHOUT
HONKS
ACTIVATES SILENT UNLOCK WITHOUT
HONKS
+
PAGE 4
72 SERIES
OWNER'S MANUAL
QUICK VIEW CHART
PRESS & HOLD 2 TURN OFF REMOTE STARTER
START
AUX
5 SECONDS 2AUXILIARY #2 OUTPUT
1 SEC 1 2ND CAR LOCK
3 SEC 1 2ND CAR ACTIVATE PANIC*
PRESS THEN
RELEASE THEN
PRESS & HOLD
12ND CAR
OUTPUT
ACTIVATE CONSTANT LOCK
BUTTON PRESS HONKS /
FLASH SYSTEM FUNCTION
BUTTON
1 SEC 2 2ND CAR UNLOCK
1 SEC
WHILE PANIC IS
TRIGGERED
NONE 2ND CAR
DOORS STAY LOCKED
TURNS OFF HORN BUT THE
+
+
SERVICE MODE / EMERGENCY OVERRIDE MODE
PAGE 5
72 SERIES
OWNER'S MANUAL
QUICK VIEW CHART
2ND CAR
OPERATION
2ND CAR
OPERATION
ACTIVATING / DEACTIVATING VALET MODE / EMERGENCY OVERRIDE
Turn the Ignition Key ON
(Leaving the key ON)
Press and hold the Valet switch for 8 to 15 seconds
(Time depends on "Valet Settings" Program Option)
TO AVOID SERIOUS INJURY, this remote start system must be set into Service Mode
before any under hood servicing is started. Service Mode will prevent the vehicle from
starting while the vehicle is being serviced. It is the sole responsibility of the vehicle’s
owner to place the system into Service Mode. The manufacture accepts no responsibility
for accidental starting of the vehicle while the vehicle is being serviced.
2ND CAR OPERATION IS NOT AVAILABLE ON 2WAY MODELS
5 HONKS = OFF
2 HONKS = ON
REMOTE START DEACTIVATED
REMOTE START ACTIVATED

1 SECOND 1 LOCK DOORS
3 SECONDS 1ACTIVATE PANIC MODE
PRESS THEN
RELEASE THEN
PRESS & HOLD
1 ACTIVATE CONSTANT LOCK OUTPUT
LOCK
BUTTON PRESS HONKS /
FLASH SYSTEM FUNCTION
BUTTON
1 SECOND 2UNLOCK DOORS
1 SECOND
WHILE ALARM IS
TRIGGERED
NONE TURNS OFF PANIC BUT DOOR STAY
LOCKED
UNLOCK/
TRUNK
PRESS & RELEASE 1 ACTIVATES REMOTE STARTER
PRESS AND HOLD
HOLD FOR 3 SEC
2
ON
AUXILIARY #1 OUTPUT (DEFAULT)
CAR FINDER (PROGRAMMABLE)
PRESS TOGETHER
THEN RELEASE
PRESS TOGETHER
THEN RELEASE
1
2
ACTIVATES SILENT LOCK WITHOUT
HONKS
ACTIVATES SILENT UNLOCK WITHOUT
HONKS
+
PAGE 4
72 SERIES
OWNER'S MANUAL
QUICK VIEW CHART
PRESS & HOLD 2 TURN OFF REMOTE STARTER
START
AUX
5 SECONDS 2AUXILIARY #2 OUTPUT
1 SEC 1 2ND CAR LOCK
3 SEC 1 2ND CAR ACTIVATE PANIC*
PRESS THEN
RELEASE THEN
PRESS & HOLD
12ND CAR
OUTPUT
ACTIVATE CONSTANT LOCK
BUTTON PRESS HONKS /
FLASH SYSTEM FUNCTION
BUTTON
1 SEC 2 2ND CAR UNLOCK
1 SEC
WHILE PANIC IS
TRIGGERED
NONE 2ND CAR
DOORS STAY LOCKED
TURNS OFF HORN BUT THE
+
+
SERVICE MODE / EMERGENCY OVERRIDE MODE
PAGE 5
72 SERIES
OWNER'S MANUAL
QUICK VIEW CHART
2ND CAR
OPERATION
2ND CAR
OPERATION
ACTIVATING / DEACTIVATING VALET MODE / EMERGENCY OVERRIDE
Turn the Ignition Key ON
(Leaving the key ON)
Press and hold the Valet switch for 8 to 15 seconds
(Time depends on "Valet Settings" Program Option)
TO AVOID SERIOUS INJURY, this remote start system must be set into Service Mode
before any under hood servicing is started. Service Mode will prevent the vehicle from
starting while the vehicle is being serviced. It is the sole responsibility of the vehicle’s
owner to place the system into Service Mode. The manufacture accepts no responsibility
for accidental starting of the vehicle while the vehicle is being serviced.
2ND CAR OPERATION IS NOT AVAILABLE ON 2WAY MODELS
5 HONKS = OFF
2 HONKS = ON
REMOTE START DEACTIVATED
REMOTE START ACTIVATED

PAGE 6
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
1. Press and release the START button on the remote transmitter one time.*
*Press twice if the system is programmed for Safety Start.
2. The park lights will flash and the horn (optional) will Honk once as confirmation.
3. The vehicle will remote start and the park lights will turn on and remain on while the vehicle is
running under remote start**.
- If the remote start fails to start see the diagnostics chart at the back of the manual.
**DEFAULT RUNTIME OF THE SYSTEM IS 15 MINUTES.
Once the vehicle is remote started and you wish to enter the vehicle to drive away you must
preform the following steps.
1. Enter the vehicle then insert the key into the ignition switch.
2. Turn the key forward to the ON or RUN* position. (This is usually 2-3 key positions)
*Do not turn the key to the start position.
3. Step on the brake and the remote starter will turn off however the vehicle will continue to run
because the key is on. If the key is not in the on position when the brake is pressed the remote
starter and the vehicle will both shut off.**
** If the vehicle shuts down simply restart the engine with the key.
DO NOT TURN THE KEY TO THE START POSITION WHILE THE ENGINE IS RUNNING.
REMOTE STARTER ACTIVATION
PRESS & RELEASE
KEY TAKEOVER
TURN KEY ON
PAGE 7
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
1. While the vehicle is running with the remote starter press and hold the START button for three
seconds.
2. The park lights will flash and the horn (optional) will honk 2 times to confirm shutdown.
- Pressing the brake pedal or opening the hood will also shut down the remote starter.
THE VEHICLE WILL SHUT OFF WHEN THE RUNTIME EXPIRES (DEFAULT 15MIN)
This feature allows the user to safely leave the vehicle running without leaving the keys in the
ignition.
1. While the vehicle is running with the key press and release the START button then remove the
key from the ignition. The vehicle will run for 15 minute while you are away.
1. While the vehicle is running with the remote starter, press and release the START button.
2. The park lights will flash and the horn (optional) will honk one time as confirmation.
The system will reset the run time (See Example Below)**.
**Not available with 4 minute run time.
Example- If the vehicle has been remote started for 10 minutes and you press and release the
start button the system will run for a addition 15 minutes totalling 25 minutes of runtime.
While the vehicle is running with the key, press and release the # button. The park lights will turn
on and the horn (optional) will Honk twice ( If connected the doors will unlock). When the ignition
key is turned to the “OFF” position the vehicle will remain running for 2 minutes.
REMOTE STARTER SHUT DOWN
PRESS & HOLD
ENGINE IDLE MODE
PRESS & RELEASE
EXTENDED RUNTIME
PRESS & RELEASE
TURBO TIMER MODE
PRESS & RELEASE

PAGE 6
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
1. Press and release the START button on the remote transmitter one time.*
*Press twice if the system is programmed for Safety Start.
2. The park lights will flash and the horn (optional) will Honk once as confirmation.
3. The vehicle will remote start and the park lights will turn on and remain on while the vehicle is
running under remote start**.
- If the remote start fails to start see the diagnostics chart at the back of the manual.
**DEFAULT RUNTIME OF THE SYSTEM IS 15 MINUTES.
Once the vehicle is remote started and you wish to enter the vehicle to drive away you must
preform the following steps.
1. Enter the vehicle then insert the key into the ignition switch.
2. Turn the key forward to the ON or RUN* position. (This is usually 2-3 key positions)
*Do not turn the key to the start position.
3. Step on the brake and the remote starter will turn off however the vehicle will continue to run
because the key is on. If the key is not in the on position when the brake is pressed the remote
starter and the vehicle will both shut off.**
** If the vehicle shuts down simply restart the engine with the key.
DO NOT TURN THE KEY TO THE START POSITION WHILE THE ENGINE IS RUNNING.
REMOTE STARTER ACTIVATION
PRESS & RELEASE
KEY TAKEOVER
TURN KEY ON
PAGE 7
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
1. While the vehicle is running with the remote starter press and hold the START button for three
seconds.
2. The park lights will flash and the horn (optional) will honk 2 times to confirm shutdown.
- Pressing the brake pedal or opening the hood will also shut down the remote starter.
THE VEHICLE WILL SHUT OFF WHEN THE RUNTIME EXPIRES (DEFAULT 15MIN)
This feature allows the user to safely leave the vehicle running without leaving the keys in the
ignition.
1. While the vehicle is running with the key press and release the START button then remove the
key from the ignition. The vehicle will run for 15 minute while you are away.
1. While the vehicle is running with the remote starter, press and release the START button.
2. The park lights will flash and the horn (optional) will honk one time as confirmation.
The system will reset the run time (See Example Below)**.
**Not available with 4 minute run time.
Example- If the vehicle has been remote started for 10 minutes and you press and release the
start button the system will run for a addition 15 minutes totalling 25 minutes of runtime.
While the vehicle is running with the key, press and release the # button. The park lights will turn
on and the horn (optional) will Honk twice ( If connected the doors will unlock). When the ignition
key is turned to the “OFF” position the vehicle will remain running for 2 minutes.
REMOTE STARTER SHUT DOWN
PRESS & HOLD
ENGINE IDLE MODE
PRESS & RELEASE
EXTENDED RUNTIME
PRESS & RELEASE
TURBO TIMER MODE
PRESS & RELEASE

PAGE 8
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
TRUNK RELEASE/ AUX 2 OUTPUT
1. Press then HOLD the Unlock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk two times.
3. The doors will unlock and the dome lights will activate. (optional)
4. The LEDs will stop flashing.
5. Continue to HOLD the Unlock Button until the trunk release activates.
NOTES:
- For safety, the trunk release will not active when ignition key is ON.
** Optional Feature may require additional parts and labor.
PRESS & HOLD
1. Press and release the Lock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will Honk one time.
3. The doors will lock.
4. The LED will start flashing within five seconds.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in Service Mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in Service Mode.
See Valet / Service Mode in this manual for further information
NOTES:
- If the panic mode is activated pressing the lock button on the remote will stop the horn
from sounding.
** Optional Feature may require additional parts and labor.
NEW- The LEDs can now be programmed not to flash when the doors are locked by
the remote transmitter.
LOCK DOORS
PRESS & RELEASE
PAGE 9
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
DRIVER'S DOOR PRIORITY UNLOCK
1. Press then release the Unlock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk two times.*
3. The driver's doors will unlock and the dome lights will activate. (optional)
4. The LEDs will stop flashing.
5. Press the Unlock Button a second time within 3 seconds and all of the other doors
will unlock.*
*This is an optional feature that may not be available on all vehicles.
** Optional Feature may require additional parts and labor.
UNLOCK DOORS
1. Press then release the Unlock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk two times.
3. The doors will unlock and the dome lights will activate. (optional)
4. The LEDs will stop flashing.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in valet mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in valet mode.
See Valet / Service Mode in this manual for further information
NOTES:
- If the panic mode is activated the first press of the unlock button will turn off the horn off and
the second press will unlock the doors.
** Optional Feature may require additional parts and labor.
PRESS & RELEASE
PRESS TWICE

PAGE 8
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
TRUNK RELEASE/ AUX 2 OUTPUT
1. Press then HOLD the Unlock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk two times.
3. The doors will unlock and the dome lights will activate. (optional)
4. The LEDs will stop flashing.
5. Continue to HOLD the Unlock Button until the trunk release activates.
NOTES:
- For safety, the trunk release will not active when ignition key is ON.
** Optional Feature may require additional parts and labor.
PRESS & HOLD
1. Press and release the Lock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will Honk one time.
3. The doors will lock.
4. The LED will start flashing within five seconds.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in Service Mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in Service Mode.
See Valet / Service Mode in this manual for further information
NOTES:
- If the panic mode is activated pressing the lock button on the remote will stop the horn
from sounding.
** Optional Feature may require additional parts and labor.
NEW- The LEDs can now be programmed not to flash when the doors are locked by
the remote transmitter.
LOCK DOORS
PRESS & RELEASE
PAGE 9
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
DRIVER'S DOOR PRIORITY UNLOCK
1. Press then release the Unlock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk two times.*
3. The driver's doors will unlock and the dome lights will activate. (optional)
4. The LEDs will stop flashing.
5. Press the Unlock Button a second time within 3 seconds and all of the other doors
will unlock.*
*This is an optional feature that may not be available on all vehicles.
** Optional Feature may require additional parts and labor.
UNLOCK DOORS
1. Press then release the Unlock Button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk two times.
3. The doors will unlock and the dome lights will activate. (optional)
4. The LEDs will stop flashing.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in valet mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in valet mode.
See Valet / Service Mode in this manual for further information
NOTES:
- If the panic mode is activated the first press of the unlock button will turn off the horn off and
the second press will unlock the doors.
** Optional Feature may require additional parts and labor.
PRESS & RELEASE
PRESS TWICE

PAGE 10
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
CAR FINDER MODE
SILENT LOCK / SILENT UNLOCK
1. Press and HOLD the Lock Button for three seconds.
2.
3. The park lights will begin to flash and the horn will honk ON and OFF.
4. To turn off panic, press Lock or Unlock Buttons on remote.
5. If no button is pressed, Panic will stay active for 1 minute then turn off.
The doors will lock.
Panic Mode is a personal protection feature that allows you to activate your alarm from the
remote transmitter. This feature can be used to draw attention to your vehicle if you feel
threatened.
1. PRESS & HOLD The # Button on the remote transmitter for 5 seconds.
- The horn will honk 5 times and the park lights will flash 5 times.
This feature helps in locating your vehicle in a crowded parking lot. It allows you hear and see
your vehicle from a distance.
*The horn output must be connected and this feature must be programmed on..
1. Press then release the Lock & Unlock buttons together.
2. If the system is UNLOCKED, it will Lock the doors with no horn honks. The park
lights will flash 1 time.
3. If the system is LOCKED, it will Unlock the doors with no horn honks. The park
lights will flash 2 times.
PRESS & HOLD for 3 sec
PRESS TOGETHER
ACTIVATE PANIC MODE
PRESS HOLD
+
PAGE 11
72 SERIES
OWNER'S MANUAL
SYSTEM OPERATIONS
The Aux output can be programmed for a variety of custom applications. (SEE
DEALER FOR DETAILS)
1. To activate Auxiliary Channel 1 output press and hold the # Button for 3 seconds.
2. The system will unlock the doors then the AUX 1 output will activate.
3. Release the buttons for a momentary output or continue holding for up to a 5
second output.
This feature can be used to open the trunk, open or close power windows or control
sliding doors on minivans.
The Aux output can be programmed for a variety of custom applications. (SEE
DEALER FOR DETAILS)
1. To activate Auxiliary Channel 2 output press and hold the Unlock Buttons for 3
seconds.
2. The system will unlock the doors then the AUX 2 output will activate.
3. Release the buttons for a momentary output or continue holding for up to a 5
second output.
This feature can be used to open the trunk, open or close power windows or control
sliding doors on minivans.
AUXILIARY OUTPUT 1
AUXILIARY OUTPUT 2/ TRUNK RELEASE
Having the Auxiliary output options connected is subject to addition labour and
parts. Some features and functions are not available on all vehicles.
HOLD UNLOCK
HOLD THE # BUTTON