AURAFINA RTAV-24-OHG User manual

R
VANITY CABINET ASSEMBLY GUIDE
Item No: RTAV-24"-OHG / 605-0180
WELCOME TO AURAFINA READY-TO-ASSEMBLE VANITIES
Thank you for purchasing an AURAFINA ready to assemble vanity. You are on your
way to a beautiful, new bathroom vanity. There are a few simple tools necessary, and
some set up of your preparation/work area before you get started.
Our vanities go together easily, but you may want to ask a friend for assistance
when putting together larger vanities. One of you can align the components while
the other screws them together. Once you get going, assembly gets easier as you
improve your learning curve! While DIY-ing just remember, by assembling your own
vanity, you are saving the thousands that companies charge for “semi-custom” built
in style vanities.
Equipment: Phillips Head screw driver, flat head screw driver, cordless electric drill with the
flat and Phillips attachment bits (not necessary, but is a time saver) and a rubber mallet.
Prep Area: A dirt free carpet or the foam sheets and cardboard from your cabinet will provide
you with a scratch free cushioned work area. To save your back, working at table height is
always a good idea.
Unpack your AURAFINA vanity components and spread out the panels on your smooth prep
surface. Keep tools and the package of hardware screws, brackets, etc close by, but not under
any of the panels. Vanities ship with the hinges already secured to the door frame faces,
making installation quicker. We pre-mark all screw holes for easy acceptance of our hardware.
All hardware, mounting brackets, shelves and screws (plus extra) are provided. Hardware is
packaged in plastic bags separately from the cabinet panels so there is no damage.
 PREPARING VANITY FOR ASSEMBLY
www.AURAFINA.comPAGE 1
THE CABINETRY AND BATH COLLECTIONS

www.AURAFINA.comPAGE 2
PARTS LIST
Front Frame
1 pc
Back Panel
1 pc
Male Bracket
13 pcs Female Bracket 13 pcs Plastic Bracket 4 pcs
3 x 12mm
3 x 25mm
Round Head Screw
73 pcs
Round Head Screw
2 pcs
Toe Kick
1 pc
Right Side
1 pc Left Side 1 pc Bottom Panel 1 pc
HARDWARE LIST
A B
E F
C D
1
5
2 3 4

Place front frame (A) and back panel (E) and toe tick (F) upside down on a smooth, flat
surface to avoid any scratches.
Attach the male bracket (1) to front frame (A) and back panel (E) and toe tick (F) using
round head screws (4) and screw driver (not included) to Fasten.
www.AURAFINA.comPAGE 3
 PREPARE VANITY FOR ASSEMBLY
44
4
4
4
4
1
1
1
1
1
A
E
F
4
44
4
4
4
4
4
1
1
1
1
1
1
1
1

www.AURAFINA.comPAGE 4
 PREPARE VANITY FOR ASSEMBLY
Place right side (B) and left side (C) and bottom panel (D) upside down on a smooth, flat surface to avoid
any scratches.
Attach the female bracket (2) to right side (B) and left side (C) and bottom panel (D) using round head
screws (4) and screw driver (not included) to Fasten. Set Screws but do not tighten fully, during the
installation it is easier if the female brackets are loose. Screws to be tightened later on in the installation
process. 4
22
2
2
2
2
2
2
22
22
2
4
4
4
44
44
4
4
44
4
B
C
DNote: Make sure the set
screw hole is set, hole
side directed towards the
inside of the vanity

www.AURAFINA.comPAGE 5
 ATTACH SIDES TO FRONT
Place front frame (A) face down onto padded work surface.
Line up fasteners on the right side (B) and left side (C) of the vanity to the front frame (A). Lock fasteners
in place and fasten with round head screw (4). Set Screws but do not tighten fully, during the installation
it is easier if the female brackets are loose. Screws to be tightened later on in the installation process.
B
C
A
4
PRO TIP: When placing side panels into brackets, slide female end over male going into slot
over the face frame. While doing this, if you slightly angle the panel as the bracket makes
female to male connection, it helps lock the fasteners into the groove.

www.AURAFINA.comPAGE 6
 SLIDE IN VANITY BOTTOM PANEL
Slide bottom panel (D) into the grooves of right side (B) and left side (C), Lock fasteners in
place and fasten with round head screw (4). Install Set Screws but do not tighten fully,
this will allow for easier installation to other components of the vanity.
4
B
C
D

www.AURAFINA.comPAGE 7
 LOCK IN BACK PANEL
Line the back panel (E) to the right side (B) and left side (C). Lock fasteners in place and fasten
with round head screw (4).
Attach back panel (E) to the bottom panel (D) using round head screw (5) and
screw driver (not included) to Fasten. Install Set Screws but do not tighten fully, this will
allow for easier installation to other components of the vanity. Once back panel is installed
we suggest to go back and tighten all female brackets hardware screws.
C
B
E
4
5
5

www.AURAFINA.comPAGE 8
 TOE KICK INSTALLATION
With the finished side of the toe kick facing out, line the toe kick (F) to the right side (B)
and left side (C). Lock fasteners in place and fasten with round head screw (4).
B
D
F
4
C

www.AURAFINA.comPAGE 9
 BRACING
Screw in vinyl corner braces and you are done!
Attach plastic bracket (3) to the vanity, using round head screw (4).
4
4
3
Please Note: A hole will need to be drilled in the back of the vanity to accommodate for the
plumbing. We suggest you refer to your plumbing installer before drilling plumbing holes.