Auralex GeoFusor-22 Operation manual

Installation & User Guide
Installation & User Guide
Auralex®Acoustics, Inc.
1-800-959-3343 |317-842-2600 |Auralex.com
9955 Westpoint Drive, Suite 101, Indianapolis IN USA 46256
Auralex®Acoustics, Inc.
1-800-959-3343 |317-842-2600 |Auralex.com
9955 Westpoint Drive, Suite 101, Indianapolis IN USA 46256
GeoFusor™ Sound Diffusors
GeoFusor™ Sound Diffusors
1379-116.GeoFusor User Guide (01/13/2020 - 11:24 AM)
1379-116.GeoFusor User Guide (01/13/2020 - 11:24 AM)
Thank you for purchasing an Auralex®GeoFusor™
These are highly effective acoustic diffusion devices that can be easily wall or
ceiling mounted and the GeoFusor-22 & GeoFusor-22 FR are also sized to fit
2’x2’ drop ceiling grids.
All GeoFusor Models are supplied with the Auralex EZ-Stick Pro™pressure
sensitive peel & stick tabs.
NOTE: Be advised that the EZ-Stick Pro Tabs are designed for permanent installations and will damage drywall and
painted surfaces when removed. Auralex Tubetak Pro can also be used. See your Authorized Auralex dealer for details.
Mark the target position on your wall or ceiling where the panel will be mounted
using small pencil marks, pieces of masking tape or any similar non marring
method. Be sure the wall surface where the EZ-Stick Pro Tabs™will adhere
is free of dirt, dust or other oily contaminants. The use of rubbing alcohol to
spot clean the wall where the tabs will adhere is recommended. Avoid the use of
household cleaners.
Remove one of the release layers on the EZ-Stick Pro Tabs and affix it to the rear side
of the perimeter flange at the desired locations, usually near the corners. Apply very firm
pressure for a minimum of 15 seconds.
Thank you for purchasing an Auralex®GeoFusor™
These are highly effective acoustic diffusion devices that can be easily wall or
ceiling mounted and the GeoFusor-22 & GeoFusor-22 FR are also sized to fit
2’x2’ drop ceiling grids.
All GeoFusor Models are supplied with the Auralex EZ-Stick Pro™pressure
sensitive peel & stick tabs.
NOTE: Be advised that the EZ-Stick Pro Tabs are designed for permanent installations and will damage drywall and
painted surfaces when removed. Auralex Tubetak Pro can also be used. See your Authorized Auralex dealer for details.
Mark the target position on your wall or ceiling where the panel will be mounted
using small pencil marks, pieces of masking tape or any similar non marring
method. Be sure the wall surface where the EZ-Stick Pro Tabs™will adhere
is free of dirt, dust or other oily contaminants. The use of rubbing alcohol to
spot clean the wall where the tabs will adhere is recommended. Avoid the use of
household cleaners.
Remove one of the release layers on the EZ-Stick Pro Tabs and affix it to the rear side
of the perimeter flange at the desired locations, usually near the corners. Apply very firm
pressure for a minimum of 15 seconds.
EZ-Stick Pro Tabs: Apply very firm
pressure for a minimum of 15 seconds.
EZ-Stick Pro Tabs: Apply very firm
pressure for a minimum of 15 seconds.

Installation & User Guide
Installation & User Guide
Auralex®Acoustics, Inc.
1-800-959-3343 |317-842-2600 |Auralex.com
9955 Westpoint Drive, Suite 101, Indianapolis IN USA 46256
Auralex®Acoustics, Inc.
1-800-959-3343 |317-842-2600 |Auralex.com
9955 Westpoint Drive, Suite 101, Indianapolis IN USA 46256
GeoFusor-22 FR™/ GeoFusor-22™/ G e o Fu sor-11™
GeoFusor-22 FR™/ GeoFusor-22™/ G e o Fu sor-11™
Remove the second layer of release paper from each of the EZ-Stick Pro Tabs, carefully orient the panels position
prior to contact with the wall, then press in place with firm pressure for a minimum of 15 seconds.
The GeoFusors can be mounted using mechanical fasteners
such as screws or nails but careful drilling of the
flange will be required. Be sure to use the fastener
appropriate for the type of wall construction.
The rear cavity of the GeoFusors can be
filled with Auralex Mineral Fiber Insulation
for reduced cavity resonance and extra low
frequency control.
NOTE: When using Mineral Fiber Insulation use personal
safety equipment appropriate for the handling of fiberglass.
For more information visit
Auralex.com or call
800-959-3343
Remove the second layer of release paper from each of the EZ-Stick Pro Tabs, carefully orient the panels position
prior to contact with the wall, then press in place with firm pressure for a minimum of 15 seconds.
The GeoFusors can be mounted using mechanical fasteners
such as screws or nails but careful drilling of the
flange will be required. Be sure to use the fastener
appropriate for the type of wall construction.
The rear cavity of the GeoFusors can be
filled with Auralex Mineral Fiber Insulation
for reduced cavity resonance and extra low
frequency control.
NOTE: When using Mineral Fiber Insulation use personal
safety equipment appropriate for the handling of fiberglass.
For more information visit
Auralex.com or call
800-959-3343