austriamicrosystems AS3607 EVAL BOARD User manual

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 1 - 19
1 General Description
The AS3606/07 is an ultra compact System PMU with
integrated battery charger and HV back light driver.
The device offers advanced power management functions.
All necessary ICs and peripherals in a battery
powered mobile device are supplied by the AS3606/07.
It features 3 DCDC converters as well as 5 low noise
LDOs.
The different regulated supply voltages are programmable
via the serial control interface.
The step-up converter for the backlight can operate up
to 26V. Both constant voltage (OLED supply) as well as
constant current (white LED backlight) operations with 2
current sinks are possible. An internal voltage protection
is limiting the output voltage in the case of external component
failures.
AS3606/07 also contains a Li-Ion battery charger with
constant current and constant voltage. The maximum
charging current is 1A. An integrated battery switch and
an optional external switch are separating the battery
during charging or whenever an external power supply
is present. With this switch it is also possible to operate
with no or deeply discharged batteries. A programmable
current limit can be used to control the maximum current
used from a USB supply.
The single supply voltage may vary from 2.7V to 5.5V.
AS3606/7
–
AN01 - Evalboard
System PMU with HV Back Light Driver

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 2 - 19
Table of Contents
1 GENERAL DESCRIPTION................................................................................................................. 1
2 OTHER APPLICABLE DOCUMENTS AND PAPERS........................................................................... 3
3 FURTHER APPLICATIONS ............................................................................................................... 3
4 REVISION STATUS .......................................................................................................................... 3
5 GENERAL DESCRIPTION................................................................................................................. 3
6 GETTING STARTED ......................................................................................................................... 4
6.1 AS3606/07 Demo Software Installation .................................................................................................... 4
6.2 Connecting the Evalboard and USB Box with the PC...............................................................................5
6.3 Starting the AS3607 Demo software......................................................................................................... 6
7 AS3607 EVALBOARD 1V0 CONNECTOR AND JUMPER LOCATIONS ............................................... 7
8 APPLICATION SCHEMATIC OF AS3607 EVALBOARD 1V0............................................................... 9
9 AS3607 EVALBOARD 1V0: LAYOUT (TOP VIEW)........................................................................... 11
10 AS3607 EVALBOARD 1V0: LAYOUT (MID LAYER 1) ...................................................................... 11
11 AS3607 EVALBOARD 1V0: LAYOUT (MID LAYER 2) ...................................................................... 12
12 AS3607 EVALBOARD 1V0: LAYOUT (BOTTOM VIEW) ................................................................... 12
13 AS3606 EVALBOARD 1V1 CONNECTOR AND JUMPER LOCATIONS ............................................. 13
14 APPLICATION SCHEMATIC OF AS3606 EVALBOARD 1V1............................................................. 15
15 AS3606 EVALBOARD 1V1: LAYOUT (TOP VIEW)........................................................................... 17
16 AS3606 EVALBOARD 1V1: LAYOUT (MID LAYER 1) ...................................................................... 17
17 AS3606 EVALBOARD 1V1: LAYOUT (MID LAYER 2) ...................................................................... 18
18 AS3606 EVALBOARD 1V1: LAYOUT (BOTTOM VIEW) ................................................................... 18
COPYRIGHT ........................................................................................................................................... 19

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 3 - 19
2 Other applicable documents and papers
Data Sheet: AS3607 0v1
3 Further Applications
Applications based on the AS3607 are continuously updated. Visit our home-page:
http: //www.austriamicrosystems.com
4 Revision status
AS3607_AN01_Evalboard Application note (this document): Rev.: 1v1
AS3607 Evalboard schematic: Rev.: 1v0
AS3607 Evalboard layout Rev.: 1v0
AS3606 Evalboard schematic: Rev.: 1v1
AS3606 Evalboard layout Rev.: 1v1
5 General description
Remark: all subsequent component numbering refers to the application schematics, shown in pt. Application
Schematic.

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 4 - 19
6 Getting Started
6.1 AS3606/07 Demo Software Installation
Start the demo software Installation Shield with “Install Demo Software”.
The Install Shield will guide you through the rest of the installation.

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 5 - 19
6.2 Connecting the Evalboard and USB Box with the PC
After the successful installation of the demo software, the USB Box can be connected to the PC and to the
Evalboard as shown in the picture below.

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 6 - 19
6.3 Starting the AS3607 Demo software
The correct installed demo software can be started from Start > Programs > austriamicrosystems > AS3607
EvalSW.
USB connection is immediately indicated in the status bar of the demo software.

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 7 - 19
7 AS3607 Evalboard 1V0 connector and jumper locations
Listed below are the various connectors and jumpers.
Jumper Function
comment
J1 PVDD1 measurement pinhead of LDO PVDD1
J2 CVDD1 measurement pinhead of DCDC CVDD1
J3 I2C Interface USB-Box connector
J4 PVDD2 measurement pinhead of LDO PVDD2
J5 CVDD2 measurement pinhead of DCDC CVDD2
J6 PVDD3 measurement pinhead of LDO PVDD3
J7 CVDD3 measurement pinhead of DCDC CVDD3
J8 PVDD4 measurement pinhead of LDO PVDD4
J9 I USB current measurement jumper of charge current
J10 measurement pinhead
J11 ON LED status LED connected to VDD27
J12 VBAT Battery voltage measurement pinhead
J13 CURR1 current measurement jumper of CURR1
J14 CURR2 current measurement jumper of CURR2
J15 GPIO1 if set, LED D12 is connected to GPIO1
J16 GPIO2 if set, LED D13 is connected to GPIO2
J17 measurement pinhead
J18 I BAT current measurement jumper of battery current
J20 DVDD DVDD can be supplied with one of the regulators; default: set to VDD27
J21 regulator output DVDD can be supplied with one of the regulators; default: set to VDD27
J22 BATTEMP
J23, J24,
J26,J27
VSS
J25 disable protection jumper
J29,J30 GPIO3, GPIO4 if set, pull up resistor is connected to GPIO3/4
BU1 –
BU7
LDO and DCDC converter output
BU9 Charger input Charger input: 2mm connector
U2 Charger input Charger input: USB connector
B12 VBAT+ Battery connector
B13 VBAT- Battery connector
B8,B10,
B13
VSS
S1 ON ON button
S2 Reset Reset button

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 8 - 19
Connector and Jumper locations of AS3607 Eval Board 1V0

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 9 - 19 8 Application Schematic of AS3607 Evalboard 1v0
Application Schematic AS3607 Evalboard 1v0- page 1

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 10 - 19
Application Schematic AS3607 Evalboard 1v0 – page2

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 11 - 19
9 AS3607 Evalboard 1v0: Layout (top view)
Layout (top view)
10 AS3607 Evalboard 1v0: Layout (mid layer 1)
Layout (mid1 view)

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 12 - 19
11 AS3607 Evalboard 1v0: Layout (mid layer 2)
Layout (mid2 view)
12 AS3607 Evalboard 1v0: Layout (bottom view)
Layout (bottom view)

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 13 - 19
13 AS3606 Evalboard 1V1 connector and jumper locations
Listed below are the various connectors and jumpers.
Jumper Function
comment
J1 PVDD1 measurement pinhead of LDO PVDD1
J2 CVDD1 measurement pinhead of DCDC CVDD1
J3 I2C Interface USB-Box connector
J4 PVDD2 measurement pinhead of LDO PVDD2
J5 CVDD2 measurement pinhead of DCDC CVDD2
J6 PVDD3 measurement pinhead of LDO PVDD3
J7 CVDD3 measurement pinhead of DCDC CVDD3
J9 I USB current measurement jumper of charge current
J10 measurement pinhead
J11 ON LED status LED connected to VDD27
J12 VBAT Battery voltage measurement pinhead
J13 CURR1 current measurement jumper of CURR1
J14 CURR2 current measurement jumper of CURR2
J15 GPIO1 if set, LED D12 is connected to GPIO1
J16 GPIO2 if set, LED D13 is connected to GPIO2
J17 measurement pinhead
J18 I BAT current measurement jumper of battery current
J20 DVDD DVDD can be supplied with one of the regulators; default: set to VDD27
J21 regulator output DVDD can be supplied with one of the regulators; default: set to VDD27
J22 BATTEMP
J23, J24,
J26,J8
VSS
J25 disable protection jumper
BU1 –
BU7
LDO and DCDC converter output
BU9 Charger input Charger input: 2mm connector
U2 Charger input Charger input: USB connector
B12 VBAT+ Battery connector
B13 VBAT- Battery connector
B8,B10,
B11
VSS
S1 ON ON button
S2 Reset Reset button

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 14 - 19
Connector and Jumper locations of AS3606 Eval Board 1V1

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 15 - 19 14 Application Schematic of AS3606 Evalboard 1v1
Application Schematic AS3606 Evalboard 1v1 – page1

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 16 - 19
Application Schematic AS3606 Evalboard 1v1 – page2

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 17 - 19
15 AS3606 Evalboard 1v1: Layout (top view)
Layout (top view)
16 AS3606 Evalboard 1v1: Layout (mid layer 1)
Layout (mid1 view)

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 18 - 19
17 AS3606 Evalboard 1v1: Layout (mid layer 2)
Layout (mid2 view)
18 AS3606 Evalboard 1v1: Layout (bottom view)
Layout (bottom view)

AS3606/7
Preliminary Application Note - Confidential
www.austriamicrosystems.com (dgm) Revision 1v1 / 20100309 19 - 19
Copyright
Copyright © 1997-2009, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-
Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted,
merged, translated, stored, or used without the prior written consent of the copyright owner.
All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Diclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions
appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by
description regarding the information set forth herein or regarding the freedom of the described devices from
patent infringement. Austriamicrosystems AG reserves the right to change specifications and prices at any time
and without notice. Therefore, prior to designing this product into a system, it is necessary to check with
austriamicrosystems AG for current information.
This product is intended for use in normal commercial applications. Applications requiring extended temperature
range, unusual environmental requirements, or high reliability applications, such as military, medical life-support
or lifesustaining equipment are specifically not recommended without additional processing by
austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might
show deviations from the standard production flow, such as test flow or test location.
The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However,
austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not
limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect,
special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing,
performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise
or flow out of austriamicrosystems AG rendering of technical or other services.
Contact Information
Headquarters
austriamicrosystems AG
A-8141 Schloss Premstätten, Austria
T. [phone]
F. [phone]
For Sales Offices, Distributors and Representatives, please visit:
http://www.austriamicrosystems.com/contact