Autoglide CASA-M Series User manual

SLIDING GATE OPENERS
Model:
Best Quality
The strongest solution for sliding gates
Product manual
Designed for residential application
Model : Casa–080M/Casa-
120M/Casa
This product is CE certified
This product is
CCC certified
SLIDING GATE OPENERS
Model:
CASA-M
Series
Best Quality
The strongest solution for sliding gates
Product manual
Designed for residential application
120M/Casa
-170M
PURE COPPER CORE
This product is CE certified
CCC certified
SLIDING GATE OPENERS
The strongest solution for sliding gates

Safety Protection and Precautions
Casa M series door machine need professional technician for the installation:
（1）All the operations must be implemented according to the instructions, this is very
Important to personal safety. Improper installation or misuse of the product might cause
series damage to personal and property.
（2）Please read instructions carefully before installation.
（3）Installation and machine fittings must comply with standards related.
（4）Power supply should be consistent with the requirements of the machine and well
grounding. Electric leakage as well as circuit short protection device should be equipped.
（5）Before system maintenance, cut off the power , and check if the grounding is well
connected
（6）Strongly recommended to install safety devices(such as infrared protection),and take
frequent check to ensure normal work.
（7）Our company is out of responsibility for any operation or use violating the instructions.
（8）Our company is out of responsibility for the consequences caused by user’s ignoring the
Process requirements of precision components during operation.
（9）Our product is in strict accordance with the instructions for the design and manufacture.
Any violation of the instructions may damage the product or cause danger.
（10）Our company shall not be responsible for safety problems caused by using fittings that
isn’t produced by our company.
（11）Any attempts to change the structure of the components is forbidden.
（12）The installation personnel should give detailed operation methods to the users as well as
the regulations under emergency, also the “instructions ”should offered.
（13）During installation, keep the children and other unrelated person away from the
installation site.
（14）Before electric control system operate, remove all the barriers within the door covering
area and any vehicles or person are forbidden to pass.
（15）Both the installation position and height of main control box should be proper, do not be
exposed to sunlight and rain, forbidden to let children to operate the remote control as
well as control panel switch.
（16）If it is necessary to install a outer shield, consider that if it may shield signal of the remote
control.
（17）Place the remote control out of the reach of children in case of accident.
（18）Any attempts to dismantle this machine privately is forbidden, please contact professional
technician.
（19) Please save the instructions properly for future use.

Main Technical Specifications
Working Principle and Main Components and Functions
The door opener mainly consists of a high-strength aluminum alloy box,a high-quality single-phase motor,a
frictional overrun clutch, a worm-gear reducer, a gear clutch and an output gear.During the operation,the
motor spindle drives both the reducer and output gear by means of the frictional overrun clutch, and the
output gear then push racks mounted on the sliding door to move the door horizontally, so that the door
can be opened and closed in the energized state.
When the special key is turned clockwise,the gear clutch is engaged and the motor power transmitted by
the worm gear drives the output gear to rotate via the gear clutch so as to drive the rack mounted on the
door, pushing the door to move (or to open and close) horizontally. Meanwhile because of the reverse
self-locking feature of the worm gear mechanism, the door is locked as well, keeping closed against an
external force.
When the special key is turned counterclockwise, the left and right parts of the gear clutch are disengaged
from each other and the output gear is freed from the influence of the motor, allowing the door to be
opened and closed manually.
Model Casa–080M/Casa-120M/Casa-170M Casa-200MH
Working voltage AC single phase 120V/220V ～ 240V 50/60HZ
Motor Power 370W /450W /750W /900W /1200W 550W /750W /900W /1200W
Starting current 5 A 3 A
Torque 18Nm /22Nm /50Nm /60Nm /75Nm 35Nm /40Nm /50Nm /65Nm
Running Speed 12 m / min 12 m / min
Gate Weight 500 ～ 2500 ㎏ 1200 ～ 3000 ㎏
Working
Temperature -50℃ ～ +65℃ -50℃ ～ +55℃
Noise ≤ 56 db ≤ 56 db
Certification CCC / CE CCC / CE

Install the Metal Base
The
door opener should be mounted on a metal base with
Fig.1
Mount the rack
The
easiest way to install a rack is to place it
opener, and then push the door slowly to move the tack bit by bit to the desired position.In this way, you
can make sure that the teeth of the rack are perfectly engaged with the teeth of the
don’
t forget to mark each mounting point. (See Fig.2.) Be noted not to lay the entire weight of the door onto
the gear.
door opener should be mounted on a metal base with
bolts. As
for how to install the metal base, see
Fig.1
easiest way to install a rack is to place it
on the gear teeth of the door opener first,disengaged the door
opener, and then push the door slowly to move the tack bit by bit to the desired position.In this way, you
can make sure that the teeth of the rack are perfectly engaged with the teeth of the
gear.When doing so,
t forget to mark each mounting point. (See Fig.2.) Be noted not to lay the entire weight of the door onto
Fig.2
for how to install the metal base, see
on the gear teeth of the door opener first,disengaged the door
opener, and then push the door slowly to move the tack bit by bit to the desired position.In this way, you
gear.When doing so,
t forget to mark each mounting point. (See Fig.2.) Be noted not to lay the entire weight of the door onto

Door Opener Release Device (Open the door manually)
The door opener is designed with a lockable releas
in case of blackout. For
the release device and its operations, see Fig.3 and Fig.4
Install the Limit Switch
Install the switch bracket onto the rack by reckoning the final travel po
spring switch, adjust until to an inclination that the spring comes into contact with the switch flapper. For a
magnetic switch, the magnet should point to the motor and be located according to the position of the
magnet
ic limit switch inside the housing.
Fig.3
Door Opener Release Device (Open the door manually)
The door opener is designed with a lockable releas
e device which enables you to open the door manually
the release device and its operations, see Fig.3 and Fig.4
Install the switch bracket onto the rack by reckoning the final travel po
sition.(See Fig.5 and Fig.6). For a
spring switch, adjust until to an inclination that the spring comes into contact with the switch flapper. For a
magnetic switch, the magnet should point to the motor and be located according to the position of the
ic limit switch inside the housing.
Fig.4
e device which enables you to open the door manually
sition.(See Fig.5 and Fig.6). For a
spring switch, adjust until to an inclination that the spring comes into contact with the switch flapper. For a
magnetic switch, the magnet should point to the motor and be located according to the position of the

Fig.5 Magnetic Limit Switch
Fig
For wiring, see Fig.7
Fig
.6 Spring Limit Switch
Fig.7

Energizing and Trial Run
1. Before use, check the power supply voltage, frequency and the other data carefully and make sure they
are in line with the requirements, and check if the ground wire is in good condition and the electrical wiring
is correct.
2. A special key is provide along with the shipment of the door opener. Turn the key counterclockwise (to
disengage the clutch), push the sliding door and let the door opener to operate without load. If the door
opener works properly, then turn the key clockwise (to engage the clutch).
3. Turn on the power, start the door opener, and observe the sliding operation of the sliding door.
4. Adjust the magnet’s position until the door is able to open and close in positions to your satisfaction.
Care and Maintenance
1. Apply some anti-rust grease to the end of the worm gear spindle located inside the hole of the special
key.
2. Check frequently if the electrical grounding is in good condition.
3. Check frequently if all parts and components are in good condition.
4. The device uses advanced lubricant that requires no replacement or replenishment.

INSTRUCTION MANUAL
Read carefully
Introduction of Item Function:
In order to enable the installation and testing easier and convenient, we developed the intelligent type
of self-study sliding gate opener controller. Which applied the imported micro-computer chip. It
features digital control, versatile functions, safety, and simple installation and testing.
Product Features
1、The gate will slowly travel to the limit position at first operation, avoiding the inertial over-limit.
2、Anti-collision design: When the motor travel is completed, only after press the reverse button, the
motor can be activated so that the over-travel can be avoided. Note: There have power-off hold
function when the motor touched the limit; it will be reverse action when power on.
3、Configuring the Hall Element, When magnets are installed, they are divided into the south
and north poles (so the magnet can attract each other while being amounted). You can ignore
their position. The motor would stop when it should be only if the motor movement and travel
input light are same color. If the direction is wrong, you can change the direction via red dip 8.
4、Motor time protection: Avoid long time operation of the motor when travel failure,The controller can
automatically learning the motor working time, which is ten seconds longer than the traveling time
without set up manually,it will automatically saved after the motor complete working several times.
5、Auto-closing function: The time can be adjusted from 1 to 250 seconds.
6、Motor force adjustment：Available.
7、Motor slow speed adjustment: Can adjust the thrust when motor running at slow speed.
8、Resistance rebound function: Can adjust the obstruction by potentiometer.
9、Top confidentiality controller has remote control function, which keep the long distance and
anti-interference. The code number is amount to 400 million combination and impossible to break
because of using the most advanced jump coding technology, more safe and confidential than the
traditional one.
(1) Working power supply 220V±10%
(2) Max. Output current: 10 A
(3) Fuse: AC220V 10A
(4) Remote distance: ＞30m
(5) Working temperature range: -25℃~+75℃, relative humidity: ＜60%, no freezing dew

Wiring Diagram
Transformer

Red Dip Switch Function:
1
、
Remote single key 2
、
None 3
、
Auto close function 4
、
Soft stop function
5
、
Max.start force 6
、
Function setting 7
、
Resistance rebound function
8
、
Motor direction, turn on this switch will change the motor and limit direction at the same time
Add and Delete Remote Control
1.Add remote control
Release your hand after press STUDY key for 1 second , then press any button on remote, finished when you
hear a sound then release your hand. Repeated above operation when you need add more remote
control.max. remote control you can add is 300 pieces.
2、 Delete remote control
Press STUDY key for 8 seconds, release your hand after hear a sound, delete all the remote control.
3、Remote control single key control:
when the Red Dip Switch1 in ON position,the remote control is single key circulation mode, open -stop-close
circulation
4、Remote control three keys control
when the Red Dip Switch1 inOFF position, the remote control is three keys control mode.
Function Operation
1、Remote single key control B1 ( Red DIP switch 1)
Red Dip Switch1 in ON position
，
the remote control is in single key circulation mode
Red Dip Switch1 in OFF position ,the remote control is in three keys mode
2、Motor direction conversion B2
empty
(Red DIP switch 2)
3、Auto-closing function B3 (Red DIP switch 3)
Red Dip Switch 3 in ON position, with auto-closing function.
When motor open to the open limit,start closing time counting.
Auto Close Time setting:
Turn onRed Dip Switch 3 and Red Dip6 to ON, Press function key
(F), one
time
one
second, after setting,
turn
R
ed
D
ip
S
witch 6 to OFF,
and Red Dip switch 3 still in ON

4、Slow speed function B4(Red DIP switch 4)
Red Dip Switch4 in ON positionwith slow speed function, it will auto learn the travelling,
and do not need manually setting. When power on for the first time, press remote control ,motor will be
move to the limit slowly, and then press the counter-direction, motor will
be fast and then slow speed to the limit. Repeat this steps 2 times with remote control, after hear
DI sound, travel setting is finished. Do not stop the motor during the process of setting.
(Note:It can adjust the slow speed thrust by MT knob if motor thrust not enough. Motor
slow position is fixed, about 20cm. )
5、Max.force startingfunction B5 (Red DIP switch 5)
Red Dip Switch 5 in ON position with max.force starting. If the door is heavy and can not start by soft start, it
can turn on Red Dip switch 5 to on, make the door starting, but this will increase the noise from door starting.
6、Function setting B6 (Red DIP switch 6)
RED Dip Switch 6 in ON position ,can set the function of the remote single key control and auto closing time
and so on ,it needs to turn to OFF after finished the setting.
7、Resistance rebound function B7 (Red DIP switch 7)
RED Dip Switch 7 in ON position with resistance rebound function.
Functional optimal adjustment scheme:Set the resistance potentiometer to minimum, then gradually
increase clockwise to find a point of appropriate force. The force cant too small and too big.
8、Motor direction conversionB8 (Red DIP switch 8)
When the gate traveling direction and limit are in correspondingposition , the gate is not in limit position and
do not have movement, just turn red dip switch 8 to change the direction, others do not change.
Loop Detector
Three states of Loop detector input:
1
、
When the gate is closing, there is loop detector signals input. The gate will reverse to the opening position.
Then the gate will close after 2 seconds delay
2
、
When the gate is opening, there is loop detector signals input, the motor continues to running, the gate
will close after 2 seconds delay when the opening travel is over.
3
、
When the motor touched the limit, and the gate will close after loop detector signal input two seconds
Usage of IR sensor

During closing, when IR sensor is interrupted, the motor will stop immediately and reverse to the opening
position.
Optional Accessories
1、Warning light
Motor can be connect with AC 220V warning light
2、Emergency stop switch
During motor working, the gate will be stop immediately when press this button
3、Manual switch
Troubleshooting Methods
Failures Reasons Methods
Control board No reaction 1. Is it power on 1. Check power supply
Press the remote but the gate
not move
1. If the remote control coded
2. Remote control battery no
power
1.
Reference the manual of
add remote control
2. Replace the battery with
same model.
The remote distance is too
short
1. The batteryPower shortage
2. The same frequency
interfere the remote control
1. Replace the old battery with
the new battery
2. Find out the source of
interference,suppress
interference
www.autoglideglobal.com