Automationdirect.com Productivity 2000 P2-16ADL-1 User manual

1
Sales 800-633-0405 www.productivity2000.com
Terminal Block sold separately, (see wiring options on page 5).
Warranty: Thirty-day money-back guarantee. Two-year limited
replacement. (See www.productivity2000.com for details).

®
WARNING: To minimize the risk of potential safety problems, you should
follow all applicable local and national codes that regulate the installation
and operation of your equipment. These codes vary from area to area and
it is your responsibility to determine which codes should be followed, and to
verify that the equipment, installation, and operation are in compliance with
the latest revision of these codes.
Equipment damage or serious injury to personnel can result from the
failure to follow all applicable codes and standards. We do not guarantee
the products described in this publication are suitable for your particular
application, nor do we assume any responsibility for your product design,
installation, or operation.
If you have any questions concerning the installation or operation of
this equipment, or if you need additional information, please call Technical
Support at 770-844-4200.
This publication is based on information that was available at the time
it was printed. At AutomationDirect.com®we constantly strive to improve
our products and services, so we reserve the right to make changes to
the products and/or publications at any time without notice and without
any obligation. This publication may also discuss features that may not be
available in certain revisions of the product.
Connector Specifications
Connector Type 24-Pin Molex Style 43025-2400
Number of Pins 24
Pin Spacing 3x3 mm (0.118 x 0.118 in)
P2-16ADL-1 Analog Input
The P2-16ADL-1 Low Resolution Current
Analog Input Module provides sixteen channels
for receiving 0-20mA signals for use with the
Productivity2000 System.
Warning .................................. 1
Connector Specifications..................... 1
General Specifications ...................... 2
Input Specifications ......................... 2
Wiring Diagram and Schematic................ 3
Module Installation Procedure................. 4
QR Code ................................. 4
Hot Swap Information ....................... 4
Wiring Options............................. 5
Module Configuration ....................... 5
Linear Scaling ............................. 6
Non-Linear Scaling ......................... 6

2Tech Support 770-844-4200www.productivity2000.com
General Specifications
Operating Temperature 0º to 60ºC (32º to 140ºF)
Storage Temperature -20º to 70ºC (-4º to 158ºF)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance > 10MΩ @ 500VDC
Heat Dissipation 1100mW maximum
Enclosure Type Open Equipment
Agency Approvals UL 61010-1 and UL 61010-2-201 File E139594, Canada & USA
CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-2-201 Safety)*
Module Keying to Backplane Electronic
Module Location Any I/O slot in a Productivity2000 System
Field Wiring ZIPLink Wiring System ONLY. See “Wiring Options” on page 5.
Must use copper conductors 75°C or equivalent.
EU Directive
See the “EU Directive” topic in the Productivity Suite Help File.
Information can also be obtained at:
www.productivity2000.com
Terminal Type 18-position Removable Terminal Block
Weight 100g (3.5 oz)
Input Specifications
Input Channels 16 sinking
Module Signal Input Range 0–20 mA
Signal Resolution 13-bit
Resolution Value of LSB
(least significant bit)
0–20 mA = 2.44μA per count
( 1 LSB = 1 count)
Data Range 0–8191 counts
Input Type Single-ended (1 common)
Maximum Continuous Overload ±44mA
Input Impedance 124Ω, ±0.5% 1/2W Current Input
Filter Characteristics Low Pass, -3dB @ 120Hz
Sample Duration Time 2ms per channel
(does not include ladder scan time)
All Channel Update Rate 25ms
Open Circuit Detection Time Zero reading within 100ms
Conversion Method Successive approximation
Accuracy vs. Temperature ±75PPM / ºC maximum
Maximum Inaccuracy 0.5% of range
(including temperature changes)
Linearity Error (end to end) ±0.036% of range
Monotonic with no missing codes
Input Stability and Repeatability ±0.024% of range
Full Scale Calibration Error
(including offset) ±0.097% of range
Offset Calibration Error ±0.097% of range
Max Crosstalk 4 counts / 0.048% of range
Recommended Fuse (external) Edison S500-32-R, 0.032A fuse
External DC Power Required 24VDC (-20% / +25%) @ 35mA
*Meets EMC and Safety requirements. See the D.O.C. for details.

3
Sales 800-633-0405 www.productivity2000.com
.032A
2-Wire 4-20 mA
Transmitter
fuse
.032A
fuse
N
o
t
e
: D
o
n
o
t
co
nn
ec
t
bo
th
e
n
ds
o
f
s
hi
e
l
d
.
I+
I+
COM
4-Wire 4-20 mA
Transmitter
Current Input Circuits
2-Wire Transmitter
4-Wire Transmitter
An Edison S500-32-R 0.032A fast-acting
fuse is recommended for current loops.
+24VDC User
Supplied Power
+
–
+
–
User Supplied
Transmitter Power
AC or DC
+
.032A
fuse
COM
I+
3-Wire Current
Transmitter
3-Wire Transmitter
+
–+24VDC User
Supplied Power
+–
+–
COM
Wiring Diagram Schematic
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
ISOLA TED
ANALOG
CIRCUIT
POWER
CH11 ADC
CH15 ADC
CH12 ADC
CH16 ADC
COM
COM
COM
COM
I1+
I5+
I2+
I6+
I3+
I7+
I4+
I8+
+V
+V
-V
-V
I9+
I13+
I10+
I14+
I11+
I15+
I12+
I16+
CH9 ADC
CH13 ADC
CH10 ADC
CH14 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
+
ISOLATED ANALOG
CIRCUIT COMMON
INTERNAL
MODULE
CIRCUITRY

4Tech Support 770-844-4200www.productivity2000.com
QR Code
Use any QR Code reader application to
display the module’s product insert.
Important Hot-Swap Information
The Productivity2000 PAC supports hot-swap!
Individual modules can be taken offline, removed, and
replaced while the rest of the PAC system continues
controlling your process. Before attempting to use the
hot-swap feature, be sure to read the hot-swap topic in
the programming software’s help file or our online docu-
mentation at AutomationDirect.com for details on how to
plan your installation for use of this powerful feature.
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
WIRE STRIP
LENGTH
WIRE STRIP
LENGTH
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking tab
toward module face. Click indi-
cates lock is
engaged.
Step Three: Attach field wiring using the removable
terminal block or ZIPLink wiring
system.
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

5
Sales 800-633-0405 www.productivity2000.com
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
ZIPLink pre-wired
terminal block cables
0.5m (1.6FT) cable
1.0m (3.3FT) cable
2.0m (6.6FT) cable
ZIPLink Modules
ZL-P2-CBL24
ZL-P2-CBL24-1
ZL-P2-CBL24-2
ZL-RTB20
ZL-RTB20-1
2Terminal Block with pigtail cable
1.0m (3.3FT) cable
2.0m (6.6FT) cable
ZL-P2-CBL24-1P
ZL-P2-CBL24-2P
3Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
Module Configuration
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16ADL-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
13
ZL-RTB20
ZL-RTB20-1
1. Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground

6Tech Support 770-844-4200www.productivity2000.com
Select the Input and Output tags appropriate
for the application. Convert raw input signals
to engineering units for use in the program, or
convert engineering units to output signals for
control purposes
max
min
min max
12500
0
65535
220
Level Transmitte
rT
ank Level
0
.5
1
1.55
2.25
3
4.55
6.75
7
0
0
0
0
0
0
0
0
1
2
3
4
5
6
6.5
7
0
0
0
0
0
0
0
Level Transmitte
rT
ank Level
7
0
0
0
0
0
0
0
Enter values for each breakpoint in the
table. Each breakpoint will define a
segment of the non-linear scaling.
7
6
5
4
3
2
1
01 2 3 4 5 6 7 8 9
The Scale (Linear) function can be used to:
• Convert analog field input signals from the range which is native to the
analog input module to an application specific range.
• Make other linear conversions in ranges appropriate to the application.
The Scale (Non-Linear) function can be used for Non-Linear applications.
Linear Scaling Non-Linear Scaling
8191

7
Sales 800-633-0405 www.productivity2000.com

8Tech Support 770-844-4200www.productivity2000.com
Document Name Edition/Revision Date
P2-16ADL-1-DS 2nd Ed. 8/19/2019
Copyright 2015, AutomationDirect.com Incorporated/All Rights Reserved Worldwide