AutomationDirect T1K-08ND3 User manual

655
Universal Field I/O
Terminator I/O Specifications
www.automationdirect.com/fieldIO
FIELD I/O
Inputs Per Module
8 (sink/source)
Commons, Non-isolated
Ext. power: 2, isolated (4 pts. /com)
Int. power: 2, all 8 pts. internally connected
Input Voltage Range
10.8-26.4 VDC min./max.
Peak Range
30 VDC
Input Current (Typical)
4mA @ 12 VDC, 8.5mA @ 24 VDC
Input Impedance
2.8 K ohm
ON Voltage Level
> 10.0 VDC
OFF Voltage Level
< 2.0 VDC
Min. ON Current
4mA
Max. OFF Current
0.5mA
OFF to ON Response
2-8ms, Typ: 4ms
ON to OFF Response
2-8ms, Typ: 4ms
Base Power Required
35mA @ 5VDC
Status Indicators
Logic side
Weight
70g
Module Specifications
External Power
Internal Power
T1K-08ND3
8-point 12/24VDC
input module
The 8-point DC module uses a T1K08B
or T1K-08B-1 base, which is purchased
separately.
T1K-08ND3
Operating Voltage Range
12-24VDC
DC INPUT MODULES
Note: When using external power, the
module can be wired to either sink
current or source current regardless of
the module’s sink/source jumper posi-
tion. When using internal power, the
sink/source jumpers determine the
module’s configuration.

Terminator I/O Dimensions and Installation
1-800-633-0405
642 Universal Field I/O
Terminator I/O Environmental Specifications
Ambient Operating Temperature
32°F to 131°F (0°C to 55°C)
Storage Temperature
-4°F to 158°F (-20°C to 70°C)
Ambient Humidity
5% to 95% (Non-condensing)
Atmosphere
No corrosive gases. The level of environmental
pollution = 2 (UL 840)
Vibration Resistance
MIL STD 810C, Method 514.2
It is important to understand the instal-
lation requirements for your Terminator
I/O system. This will help ensure that the
Terminator I/O products work within
their environmental and electrical limits.
Plan for safety
This catalog should never be used as a
replacement for the technical data sheet
that comes with the products or the
T1K-INST-M Installation and I/O
Manual (It is also available online at
www.automation-direct.com.) The tech-
nical data sheet contains information
that must be followed. The system instal-
lation should comply with all appro-
priate electrical codes and standards.
Unit dimensions and
mounting orientation
Use the following diagrams to make sure
the Terminator I/O system can be
installed in your application. Terminator
I/O units can be mounted horizontally
or vertically. However, to insure proper
airflow for cooling purposes, units
should not be mounted upside-down. It
is important to check the Terminator I/O
dimensions against the conditions
required for your application. For
example, it is recommended to leave 2”
depth for ease of access and cable clear-
ance. However, your distance may be
greater or less. Also, check the installa-
tion guidelines for the recommended
cabinet clearances.
Shock Resistance
MIL STD 810C, Method 516.2
Voltage Withstand (Dielectric)
1500VAC, 1 minute
Insulation Resistance
500VDC, 10M ohm
Noise Immunity
NEMA ICS3-304
Impulse noise 1us, 1000V
FCC class A
RFI (144MHz, 430MHz 10W, 10cm)
Agency Approvals
UL, CE, FCC class A, NEC Class 1 Division 2
48mm
(1.89in)
80mm
(3.15in) 80mm (3.15in)
48mm
(1.89in)
80mm
(3.15in)
48mm
(1.89in) 89mm (3.5in)
80mm
(3.15in)
83.3mm
(3.28in)
Power Supply Network Interface Module Half-size I/O Module
with Base System HeightFull-size I/O Module with Base
DIMENSIONS AND INSTALLATION
See
the Enclosures section
of this desk reference for an
enclosure that may be suitable
for your application