AutomationDirect T1K-08ND3 User manual

External Power
Internal Power
T1K-08ND3 $77.00
8-point 12/24VDC
input module
The 8-point DC module uses a
T1K-08B or T1K-08B-1 base, which is
purchased separately.
DC Input Modules
Note: When using external power, the module can be wired to either sink current or source current regard-
less of the module’s sink/source jumper position. When using internal power, the sink/source jumpers
determine the module’s configuration.
Module Specifications T1K-08ND3
Inputs Per Module 8 (sink/source)
Commons, Non-isolated Ext. power: 2, isolated (4 pts. /com)
Int. power: 2, all 8 pts. internally connected
Operating Voltage Range 12–24 VDC
Input Voltage Range 10.8-26.4 VDC min./max.
Peak Range 30VDC
Input Current (Typical) 4mA @ 12VDC, 8.5 mA @ 24VDC
Input Impedance 2.8 kq
ON Voltage Level > 10.0 VDC
OFF Voltage Level < 2.0 VDC
Min. ON Current 4mA
Max. OFF Current 0.5 mA
OFF to ON Response 2–8 ms, Typ: 4ms
ON to OFF Response 2–8ms, Typ: 4ms
Base Power Required 35mA @ 5VDC
Status Indicators Logic side
Weight 70g
www.automationdirect.com Universal Field I/O tFED-71
For the latest prices, please check AutomationDirect.com.
1-800-633-0405

External Power
Internal Power
T1K-16ND3 $121.00
16-point, 12/24 VDC
input module
The 16-point DC module uses a T1K-16B or
T1K-16B-1 base, which is purchased sepa-
rately.
DC Input Modules
Note: When using external power, the module can be wired to either sink current or source
current regardless of the module’s sink/source jumper position. When using internal power,
the sink/source jumpers determine the module’s configuration.
Module Specifications T1K-16ND3
Inputs Per Module 16 (sink/source)
Commons, Non-isolated Ext. power: 4, isolated (4 pts. /com)
Int. power: 4, all 16 pts. internally connected
Operating Voltage Range 12–24 VDC
Input Voltage Range 10.8-26.4 VDC
Peak Range 30VDC
Input Current (Typical) 4 mA @ 12VDC, 8.5 mA @ 24VDC
Input Impedance 2.8 Kq
ON Voltage Level > 10.0 VDC
OFF Voltage Level < 2.0 VDC
Min. ON Current 4 mA
Max. OFF Current 0.5 mA
OFF to ON Response 2–8 ms, Typ: 4ms
ON to OFF Response 2–8 ms, Typ: 4ms
Base Power Required 70mA @ 5VDC
Status Indicators Logic side
Weight 160g
www.automationdirect.com Universal Field I/O tFED-72
For the latest prices, please check AutomationDirect.com.
1-800-633-0405

T1K-08NA-1 $98.00
T1K-16NA-1 $159.00
8-point and 16-point,
90–120 VAC input modules
The 8-point AC input module uses a
T1K-08B or T1K-08B-1 base, which is
purchased separately.
The 16-point AC input module uses a
T1K-16B or T1K-16B-1 base, which is
purchased separately.
AC Input Modules
Equivalent Input Circuit
Specifications T1K-08NA-1 T1K-16NA-1
Inputs Per Module 8 16
Commons per Module 2, 4 pts. /com (isolated) 4, 4 pts. /com (isolated)
Input Voltage Range 80–132 VAC, 47–63 Hz
Operating Voltage Range 90–120 VAC, 47–63 Hz
Input Current
8mA @ 100VAC (50Hz)
10mA @ 100VAC (60Hz)
12mA @ 132VAC (50Hz)
15mA @ 132VAC (60Hz)
8mA @ 100VAC (50Hz)
10mA @ 100VAC (60Hz)
12mA @ 132VAC (50Hz)
15mA @ 132VAC (60Hz)
Input Impedance 14kq @ 50Hz, 12kq @ 60Hz
ON Current/Voltage > 6mA @ 75VAC
OFF Current/Voltage < 2mA @ 20VAC
OFF to ON Response < 40ms
ON to OFF Response < 40ms
Base Power Required 35mA @ 5VDC 70mA @ 5VDC
Status Indicators Logic side
Weight 70g 120g
www.automationdirect.com Universal Field I/O tFED-73
For the latest prices, please check AutomationDirect.com.
1-800-633-0405

It is important to understand the installa-
tion requirements for your Terminator I/O
system. This will ensure that the Terminator
I/O products work within their environmental
and electrical limits.
Plan for safety
This catalog should never be used as
a replacement for the technical data
sheet that comes with the products or the
T1K-INST-M Installation and
I/O Manual (available online at
www.automationdirect.com.) The technical
data sheet contains information that must
be followed. The system installation should
comply with all appropriate electrical codes
and standards.
Unit dimensions and
mounting orientation
Use the following diagrams to decide if
the Terminator I/O system can be installed
in your application. Terminator I/O units
should be mounted horizontally. To ensure
proper airflow for cooling purposes, units
should not be mounted upside-down. It
is important to check the Terminator I/O
dimensions against the conditions required
for your application. For example, it is
recommended to leave 2” depth for ease of
access and cable clearance. However, your
distance may be greater or less. Also, check
the installation guidelines for the recom-
mended cabinet clearances.
48mm
(1.89in)
80mm
(3.15in)
80mm
(3.15in)
48mm
(1.89in)
80mm
(3.15in)
48mm
(1.89in)
89mm
(3.5in)
80mm
(3.15in)
83.3mm
(3.28in)
Power Supply Network Interface Module Half-size I/O Module
with Base
System DepthFull-size I/O Module
with Base
Dimensions and Installation
See the Enclosures
section for an enclosure that may
be suitable for your application
Terminator I/O Environmental Specifications
Ambient Operating
Temperature 32°F to 131°F (0°C to 55°C)
Storage
Temperature -4°F to 158°F (-20°C to 70°C)
Ambient Humidity 5% to 95% (Non-condensing)
Atmosphere No corrosive gases. The level of environmental
pollution = 2 (UL 840)
Vibration
Resistance MIL STD 810C, Method 514.2
Shock Resistance MIL STD 810C, Method 516.2
Voltage Withstand
(Dielectric) 1500VAC, 1 minute
Insulation
Resistance 500 VDC, 10 Mq
Noise Immunity
NEMA ICS3-304
Impulse noise 1µs, 1000V
FCC class A
RFI (144MHz, 430MHz 10W, 10cm)
Agency Approvals UL, CE, FCC class A, NEC Class 1 Division 2
www.automationdirect.com Universal Field I/O tFED-53
For the latest prices, please check AutomationDirect.com.
1-800-633-0405

I/O Module Installation
Grip the locking handle, as shown, and pull gently to eject
the I/O module from its base. The module will slide out for
easy replacement. This procedure does not apply to network
interface modules or power supplies, which have integral
bases.
Hot-swappable
I/O modules
You can remove I/O modules
under power, but exer-
cise caution while doing
so. Do not touch the termi-
nals with your hands or
any conductive material.
Always remove power when
possible.
Removing I/O modules
is a snap
I/O module installation
Terminator I/O modules feature separate
terminal bases for easy installation.
To install I/O modules:
1. Slide the module into its terminal base (until it
clicks into position)
2. Hook upper DIN rail tabs over the top of DIN
rail, and press the assembly firmly onto the
DIN rail.
3. Slide the module along the DIN rail until it
engages with the adjacent module.
DN-ASB-1
angled mounting
bracket
Optional angled support bracket raises
and tilts the mounting rail for easier
access and wiring. Use with 35mm DIN
rail. See the Connection Systems in this
catalog for details.
Great for mounting
in upper locations
Great for mounting
in lower locations
1
2
3
www.automationdirect.com Universal Field I/O tFED-54
For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Calculating the power budget
To calculate the power budget, read the
available power (current rating) from the
Power Supply Specifications table and
subtract the power consumed by each
module to the right of the power supply. Do
not include modules to the right of an addi-
tional power supply.
Power supplies
The Terminator I/O product line offers two
power supply options: AC or DC. The power
supplies are always positioned to the left of
the modules to which they supply power.
Consult the system configuration examples
and the power budgeting example for more
information on positioning power supplies.
This power supply powers these three I/O
modules
This power supply powers the network interface module and
the next two I/O modules
Power Supplies and Power Requirements
Power requirements
Power supply
specifications
Power Supply
Specifications
T1K-01AC
$127.00
T1K-01DC
$122.00
Input Voltage Range 110/220 VAC 12/24 VDC
Input Frequency 50/60 Hz N/A
Maximum Power 50VA 30W
Max. Inrush Current 20A 10A
Insulation Resistance > 10Mq@ 500 VDC
Voltage Withstand
1 min. @ 1500VAC between
primary, secondary and field
ground
5VDC
PWR
Voltage 5.25 VDC 5.25 VDC
Current Rating
2000 mA max
(see current
option note
below)
2000mA max
Ripple 5% max. 5% max.
24VDC
PWR
Voltage 24VDC N/A
Current Rating
300mA max.
(see current
option note
below)
N/A
Ripple 10% max. N/A
Fuse 1 (primary), not replaceable
Replacement
Terminal Block
(Phoenix Contact)
MVSTBW
2.5/4-ST-5.08
BK
MVSTBW
2.5/6-ST-5.08
BK
Note: 500mA @ 24VDC can be achieved by lowering the
5VDC from 2000mA to 1500mA.
Power Budget Example
Module 5VDC 24VDC
T1K-01AC +2000mA +300mA
T1H-EBC100 -300mA -0mA
T1K-16ND3 -70mA -0mA
T1K-16TD2 -200mA -0mA
T1F-08AD-1 -75mA -50mA
Remaining +1355mA +250mA
Module 5VDC 24VDC
Analog Input Modules
T1F-08AD-1 75 50*
T1F-08AD-2 75 50*
T1F-16AD-1 75 50*
T1F-16AD-2 75 50*
T1F-16RTD 150 0
T1F-16TMST 150 0
T1F-14THM 60 70*
Analog Output Modules
T1F-08DA-1 75 150*
T1F-08DA-2 75 150*
T1F-16DA-1 75 150*
T1F-16DA-2 75 150*
Combination Analog Modules
T1F-8AD4DA-1 75 60*
T1F-8AD4DA-2 75 70*
* Use either internal or external source
for 24VDC
Module 5VDC 24VDC
DC Output Modules
T1H-08TDS 200 0
T1K-08TD1 100 200*
T1K-16TD1 200 400*
T1K-08TD2-1 200 0
T1K-16TD2-1 200 0
AC Output Modules
T1K-08TA 250 0
T1K-16TA 450 0
T1K-08TAS 300 0
Relay Output Modules
T1K-08TR 350 0
T1K-16TR 700 0
T1K-08TRS 400 0
Specialty Modules
T1H-CTRIO 400 0
* Use either internal or external source
for 24VDC
Module 5VDC 24VDC
Interface Modules
T1H-EBC100 300 0
T1K-DEVNETS 250 45
T1K-MODBUS 300 0
DC Input Modules
T1K-08ND3 35 0
T1K-16ND3 70 0
AC Input Modules
T1K-08NA-1 35 0
T1K-16NA-1 70 0
Adding additional
power supplies
Each power supply furnishes power only to
the network interface and I/O modules to its
right. Inserting a second power supply closes
the power loop for the power supply to the
left, while also powering the modules to its
right. Perform a power budget calculation
for each power supply in the system.
www.automationdirect.com Universal Field I/O tFED-55
For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Expansion I/O Configurations
T1K-10CBL $46.50
T1K-10CBL-1* $62.00
Right side to left side
expansion cable
Expansion cables
Using two T1K-10CBL expansion cables
The T1K-10CBL(-1) connects the right
side of an I/O base to the left side of
the next I/O base. A maximum of two
T1K-10CBL(-1) cables can be used per
expansion system.
*Note: The (-1) versions of the expan-
sion cables pass 24VDC through on an
isolated wire. (All cables pass the 5VDC
base power.) Any local expansion DC input
module configured for “internal power”
(current sourcing) must either have a power
supply preceding it on the same base or,
have a (-1) version cable pass 24VDC from
a power supply on the preceding base.
In the system below, power supplies can be used anywhere.
T1K-10CBL(-1) I/O Addressing
T1K-10CBL(-1)
Cable length = 1.0 m
www.automationdirect.com Universal Field I/O tFED-56
For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Terminal base
specifications
Terminator I/O terminal bases are available in
screw clamp and spring clamp versions for both
half-size and full-size modules. Hot stamp silk
screen labeling is used for numbering I/O points,
commons, and all power terminals.
Screw clamp, half-size
Screw clamp, full-size
2 and 3-wire DC input devices
using bussed 24VDC power
Use externally supplied 24VDC
power or 24VDC auxiliary power
from T1K-01AC
Spring clamp, full-size
Spring clamp, half-size
T1K-08B $62.00
T1K-16B $77.00 T1K-16B-1 $77.00
T1K-08B-1 $62.00
Field Device Wiring and Power Options
Do not jumper modules together
to create a 24VDC bus when using
the “hot swap” feature. See Note
below.
Terminal Base Specifications
Terminal Type Screw type Spring clamp
Recommended
Torque
1.77–3.54 lb·in
(0.2–0.4 N·m) N/A
Wire Gauge
Solid:
25–12 AWG
Stranded:
26–12 AWG
Solid:
25–14 AWG
Stranded:
26–14 AWG
Field device wiring options
Power your DC input devices from the
integrated 24VDC power supply bus.
T1K-08ND3 and T1K-16ND3 DC input
modules include jumpers for selecting the
internal 24VDC power supply available
for 2- and 3-wire field devices. Clearly
labeled triple stack terminals make it easy
to wire 2- and 3-wire devices ensuring
clean wiring with only one wire per
termination.
External user supplied 24VDC power, or auxil-
iary 24VDC terminals from T1K-01AC, can
be easily applied directly to one end of the
terminal rows and jumpered across each base
in the system.
This is a convenient solution for powering
analog I/O and discrete DC output devices
whose modules do not have direct access
to the internal bussed 24VDC. If current
consumption increases, simply add addi-
tional T1K-01AC power supplies into the
system.
Hot-swap feature
The hot-swap feature allows Terminator I/O
modules to be replaced while system power is
on. Be careful not to touch the terminals with
your hands or other conductive material to
avoid the risk of personal injury or equipment
damage. Always remove power if it is equally
convenient to do so.
Note: Before hot-swapping analog or
DC output modules in a Terminator I/O
system, make sure that each of the analog
and DC output module’s 24VDC and 0
VDC base terminals are wired directly to
the external power supply individually. If the
external 24VDC and 0 VDC is jumpered
from base to base in a daisy chain fashion,
and an analog or DC output module is
removed from its base, the risk of discon-
necting the external 24VDC and 0 VDC to
the subsequent I/O modules exists.
www.automationdirect.com Universal Field I/O tFED-57
For the latest prices, please check AutomationDirect.com.
1-800-633-0405