Autostart AS-2300TW User manual

DOC:.1.11 – September 24, 2004 CA LP Manufactured in Canada
AUTOMATIC TRANSMISSION REMOTE STARTER
AS-2300TW
User Guide
Table of Contents
Introduction.............................................2
Using the Remote Control......................2
Feature Confirmation Chart....................3
Vehicle Status Request..........................3
Status Request When the Engine IS NOT
Running..................................................4
Status Request When the Engine is
Running..................................................4
How Run Time Cycles Work...................5
Multi-Level Features (default state).......6
Remote-Starting Your Vehicle................7
Vehicle Presets.......................................7
Driving Off...............................................7
Using the Remote Starter.......................8
Arming the Starter Kill.............................8
Idle Mode................................................8
Turbo Mode............................................8
Valet Mode..............................................8
Valet Mode Using the Valet Switch (if
installed).................................................8
Ignition Valet...........................................9
Remote Valet Mode................................9
“Home ValetTM” Mode.............................9
Panic Mode...........................................10
Quick LockoutTM....................................10
Cold Weather Mode..............................10
Advanced Features: Installation-
programmable Options.........................10
Remote Door Locks..............................11
Priority Door Access.............................11
Active or Passive Arming......................11
The Starter Kill and the Anti-grind Feature
..............................................................11
Flashing LED........................................11
Safe Start..............................................11
Home Valet TM.......................................12
Ignition-Controlled Door Locks.............12
Ignition Re-lock.....................................12
Secure Lock..........................................12
Turbo Mode..........................................12
Remote Trunk Release.........................12
Engine Run Time..................................12
Extended Run Time..............................12
Multi-car Operation...............................12
Troubleshooting Transmitting Range....13
Diagnostics – Parking Light Flash Table14

INDUSTRY CANADA USER NOTICE:
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (EIRP) is not more
than that required for successful communication.
FCC USER NOTICE (U.S.A.):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
Introduction
This is a state-of-the-art remote starter system. The system is packed with advanced features such
as priority access to the driver’s door (commodity features) and the safe start children safety
feature. With many an advanced function, this product will satisfy any one your expectations from
high-end commodity and security systems, without neglecting any standard feature commonly
offered by entry-level starters.
Using the Remote Control
Your remote starter is equipped with a 5-button multi-channel remote control. It can operate two
independent vehicles equipped with a remote starter (see Multi-car operation section on page
12). The functions of the transmitter are as follows:
Picture serves as example only.
P. 2 User Guide AS-2300TW

AS-2300TW Guide d’installation P. 3
•
•
Pressing and holding the LOCK button for more than 3 seconds will lock all doors and will send a
constant pulse as long as the LOCK button is held down (maximum of 15 seconds). This
constant pulse can be configured to activate certain functionalities such as rolling up the
windows – Please refer to your installer to see if your vehicle is compatible with this
option.
Pressing and holding the UNLOCK button for more than 3 seconds will unlock all doors and will
send a constant pulse as long as the UNLOCK button is held down (maximum of 15 seconds).
This constant pulse can be configured to activate certain functionalities such as rolling down the
windows – Please refer to your installer to see if your vehicle is compatible with this
option.
Feature Confirmation Chart
Feature LED #1 LED #2 LED #3 LED #4 Beep(s)
Lock 3 flashes X X X 1
Unlock X 3 flashes X X 2
Trunk X X 3 flashes X 1
LED ON/OFF 3 flashes 3 flashes X X 1
Start X X X 3 flashes 1
Running X X X 3 flashes 3
Stop X X X 3 flashes 2
Entering Cold
Weather Mode X X X 3 flashes 2
Exiting Cold
Weather Mode X X X 3 flashes 1
Home Valet 3 flashes X X 3 flashes 2
Valet Mode 3 flashes X X 3 flashes 1
Exit ValetMode X 3 flashes X 3 flashes 1
Vehicle Status Request
The status request feature allows the user to see the status of the vehicle i.e.: if the doors are
locked or unlocked or if the vehicle is in cold weather mode, home valet mode, in valet mode or
how much time is left in the run time cycle. The following charts (Tables 1, 2 and 3) indicate the
confirmation sequences.
To retrieve the vehicle status:
Press and release the SHIFT button then press and release the TRUNK button (there will be a beep).
The transmitter will then flash the corresponding sequence of LEDs depending on the vehicle’s
status.
xIf the engine is NOT running, refer to Table 1.
xIf the engine IS running under a remote start, refer to Table 2 (if the doors are locked)
or refer to Table 3 (if the doors are unlocked).
The status request feature is a two-step procedure:
•The first sequence of flashes denotes if the vehicle’s doors are locked or unlocked.

P. 4 User Guide AS-2300TW
•The second sequence of flashes (if applicable) denotes if the vehicle is Cold weather mode,
Home valet mode, or, Valet mode.
•If there is no second sequence transmission, that the vehicle is not in any of the three (3)
mentioned features (Cold weather mode, Home valet mode or Valet mode).
Status Request When the Engine IS NOT Running
STATUS SEQUENCE LED #1 LED #2 LED #3 LED #4 Beep(s)
Lock 3 flashes X X X 1
Unlock X 3 flashes X X 2
1st sequence if
locked 3 flashes X X X 2
1st sequence if
unlocked X 3 flashes X X 2
Cold
Weather
2nd sequence X X X 1 second X
1st sequence if
locked 3 flashes X X X 2
1st sequence if
unlocked X 3 flashes X X 2
Home
Valet
2nd sequence 1 second X X 1 second X
1st sequence if
locked 3 flashes X X X 1
1st sequence if
unlocked X 3 flashes X X 1
Valet
Mode
2nd sequence 1 second X X 1 second X
Table 1
Status Request When the Engine is Running
When the vehicle’s doors are locked:
RUN TIME SEQUENCE LED #1 LED #2 LED #3 LED #4 Beep(s)
1st sequence 3 flashes X X X 3
If there is
more than
3/4 of run
time cycle 2nd sequence ON for 1-sec ON for 1-sec ON for 1-sec ON for 1-sec X
1st sequence 3 flashes X X X 3
If there is
more than
half of run
time cycle 2nd sequence ON for 1-sec ON for 1-sec ON for 1-sec X X
1st sequence 3 flashes X X X 3
If there is
more than
1/4 of run
time cycle 2nd sequence ON for 1-sec ON for 1-sec X X X
1st sequence 3 flashes X X X 3
If there is less
than 1/4 of
run time cycle 2nd sequence ON for 1-sec X X X X
Table 2

When the vehicle’s doors are unlocked:
Table 3
How Run Time Cycles Work
Table 4
RUN TIME SEQUENCE LED #1 LED #2 LED #3 LED #4 Beep(s)
1st sequence X 3 flashes X X 3
If there is
more than
3/4 of run
time cycle 2nd sequence ON for 1-secON for 1-sec
ON for 1-sec ON for 1-sec X
1st sequence X 3 flashes X X 3
If there is
more than
half of run
time cycle 2nd sequence ON for 1-secON for 1-sec
ON for 1-sec X X
1st sequence X 3 flashes X X 3
If there is
more than
1/4 of run
time cycle 2nd sequence ON for 1-secON for 1-sec
X X X
1st sequence X 3 flashes X X 3
If there is
less than
1/4 of run
time cycle 2nd sequence ON for 1-sec X X X X
RUN TIME
CYCLE LED #1 will turn itself off when ... LED #2 will turn itself off... LED #3 will turn itself off ... LED #4 will turn itself off...
4-minute run
time cycle ... the cycle will have ended. ... 3 minutes into the cycle. ... 2 minutes into the cycle. ...1 minute into the cycle.
9-minute run
time cycle ... the cycle will have ended. ... 7 minutes into the cycle. ... 5 minutes into the cycle. ... 3 minutes into the cycle.
15-minute run
time cycle ... the cycle will have ended. ...11 minutes into the cycle. ... 7 minutes into the cycle. ... 3 minutes into the cycle.
20-minute run
time cycle ... the cycle will have ended. ... 15 minutes into the cycle. ... 10 minutes into the cycle. ... 5 minutes into the cycle.
25-minute run
time cycle ... the cycle will have ended. ... 19 minutes into the cycle. ... 13 minutes into the cycle. ... 7 minutes into the cycle.
30-minute run
time cycle ... the cycle will have ended. ... 23 minutes into the cycle. ... 16 minutes into the cycle. ... 9 minutes into the cycle.
AS-2300TW Guide d’installation P. 5

P. 6 User Guide AS-2300TW
Example: If the vehicle was programmed with a run time cycle of 15 minutes and the engine
was running (under a remote start) for 5 minutes (meaning there is 10 minutes left in
the run time cycle), LEDs #1 #2 and #3 would light up. LED #3 will turn itself off
when there will be 8 minutes or less left in the run time cycle.
Multi-Level Features (default state)
Basic Features (press the SHIFT button 1X)
SHIFT ¾LOCK:.......................................................................aux 2
SHIFT ¾TRUNK:.....................................................................status request
SHIFT ¾START/STOP............................................................cold weather
Multi-Car Operation (press the SHIFT button 2X)
SHIFT ¾SHIFT ¾LOCK:.........................2nd car lock
SHIFT ¾SHIFT ¾UNLOCK:.....................2nd car unlock
SHIFT ¾SHIFT ¾START/STOP:...............2nd car start/stop
SHIFT ¾SHIFT ¾TRUNK:.......................2nd car trunk
Customized Features (press the SHIFT button3X)
(May not be applicable for certain vehicles)
Your installer can add customized features such as turning on the radio, opening sliding doors, etc.
SHIFT ¾SHIFT ¾SHIFT ¾......................LOCK: customized feature 1
SHIFT ¾SHIFT ¾SHIFT ¾......................UNLOCK: customized feature 2
SHIFT ¾SHIFT ¾SHIFT ¾......................TRUNK: customized feature 3
SHIFT ¾SHIFT ¾SHIFT ¾......................START/STOP: customized feature 4
Setting Transmitter Features (press the SHIFT button4X)
SHIFT ¾SHIFT ¾SHIFT ¾SHIFT:
LOCK:..............................full beep ...................................................(LED #1 flashes)
UNLOCK:..........................half beep..................................................(LED #2 flashes)
START/STOP:....................disable beep.............................................(LED #4 flashes)
TRUNK:............................save modifications ...................................(LED #3 flashes)
By default, the multi-level features are programmed as follows:
x
x
x
x
x
x
Level 1 (Basic Features)
Level 2 (Multi car operation)
Level 3 (Customized Features)
To access a feature that is programmed as level 1, press the SHIFT button once followed by the
desired function.
To access a feature that is programmed as level 2, press the SHIFT button twice followed by the
desired function.
To access a feature that is programmed as level 3, press the SHIFT button three times followed
by the desired function.
Your installer can customize the system as to personalize these multi-level features in an order that
best suits you. Your options are: Option 1:
Level 1 (requires pressing the SHIFT button 1X) ÆMulti car operation
Level 2 (requires pressing the SHIFT button 2X) ÆBasic features
Level 3 (requires pressing the SHIFT button 3X) ÆCustomized features
Option 2:
Level 1 (requires pressing the SHIFT button 1X) ÆBasic features
Level 2 (requires pressing the SHIFT button 2X) ÆMulti car operation

AS-2300TW Guide d’installation P. 7
Level 3 (requires pressing the SHIFT button 3X) ÆCustomized features
Option 3:
Level 1 (requires pressing the SHIFT button 1X) ÆCustomized features
Level 2 (requires pressing the SHIFT button 2X) ÆMulti car operation
Level 3 (requires pressing the SHIFT button 3X) ÆBasic features
Option 4:
Level 1 (requires pressing the SHIFT button 1X) ÆBasic features
Level 2 (requires pressing the SHIFT button 2X) ÆCustomized features
Level 3 (requires pressing the SHIFT button 3X) ÆMulti car operation
Example: If the multi-level features were set to option 3, the setup would be as follows:
xLevel 1 ÆCustomized feature
xLevel 2 ÆMulti car operation
xLevel 3 ÆBasic features
The “Basic features” are now programmed as level 3 and therefore:
xTo access the aux.2 feature, the user needs to press on the SHIFT button three (3) times
followed by the LOCK button.
xTo access the status request feature, the user needs to press on the SHIFT button three (3)
times followed by the TRUNK button.
xTo access cold weather mode, the user needs to press on the SHIFT button three (3) times
followed by the START/STOP button.
Remote-Starting Your Vehicle
Press the START/STOP button for approx. 1 second. The parking lights will come ON to inform you
that the remote starter has received your signal. Approximately 5 seconds later, the engine will
start. The parking lights will remain ON during the pre-programmed run time of the engine.
If the vehicle does not start at the first attempt, the system will shut down, wait a few seconds and
try to start the engine again. There will be 3 start attempts before the systemgives up.
Vehicle Presets
Heater & Heated Seat
When leaving the vehicle it is recommended to preset the accessory controls in preparation for the
next remote start. Settings for the blower motor (fan), front and rear, as well as heated seats (if
equipped) should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM
instead.
Windshield Wipers & Radio & Headlights
Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become
energized while running under remote start. When leaving the vehicle you must ensure that the
windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain types
of vehicles could cause them to remain ON even after remote starter shut down, resulting in a dead
battery.
Driving Off
With the vehicle running under remote control, press the UNLOCK button to disarm and unlock the
doors. Enter the vehicle and do the following:
Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK position
while the engine is running. This would cause the starter motor to re-engage.)
Press the brake pedal to disengage the remote starter unit.
You are now ready to drive off.

P. 8 User Guide AS-2300TW
Using the Remote Starter
Arming the Starter Kill
The starter kill (if installed) can be configured by the installer so as to arm automatically (passive
mode) or not to arm automatically (active mode). See section passive or active arming on p. 11
for more details on passive mode and active mode.
•To disarm the starter kill, press the UNLOCK button on the transmitter.
The parking lights will flash twice.
If remote door locks are installed, this will also unlock the doors.
•To arm the Starter Kill, press the LOCK button on the transmitter.
The parking lights will flash once.
If remote door locks are installed, this will also lock the doors.
•In passive mode, the starter kill will automatically arm if the ignition key is not inserted
Into the ignition switch within 1 or 3 minutes after unlocking (the key sense feature
must be installed).
Idle Mode
Convenience feature: Idle mode allows you to keep the engine running and the doors
locked while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no key in the
ignition switch) while the engine is running. For example, if you stop for a delivery or at a conveni-
ence store, lock your vehicle and leave it running for the length of a run cycle while you are away.
To leave the vehicle in idle mode:
1. With the engine running, press the LOCK or UNLOCK button (to unlock the doors) or the
START/STOP button on the remote control until the parking lights come on.
2. Remove the key and exit the vehicle. The engine will go on running.
3. Lock the doors if needed.
The engine will go on running until the user re-enters the vehicle or until the expiration of the
engine run time .
Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.
Turbo Mode
If turbo mode is configured at installation, it will allow a turbocharger to idle down after the user
leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it
is shut down by remote control), then shut down the engine.
Proceed as follows to set the system to Turbo Mode:
1. With the engine already running, press the LOCK button on the transmitter until the parking lights
come ON.
2. Remove the ignition key from the ignition switch. The engine will go on running.
3. Exit the vehicle and close the door.
4. Press the TRUNK button to lock the doors; the engine will shut down after 60 seconds of Turbo
Mode.
Valet Mode
Valet Mode Using the Valet Switch (if installed)
When your vehicle is in valet mode, the remote starter functionalities are disabled. If the vehicle
needs to be serviced, or if you park it indoors, the valet mode will prevent the engine from being
remote-started accidentally.
To put the system i n t o valet mode:

AS-2300TW Guide d’installation P. 9
1. Turn the ignition key to the IGNITION ON (RUN) position.
2. Within 3 sec., press the valet button (the L.E.D. will come ON solid).
3. The parking lights will flash three times to indicate that the vehicle is now in valet mode. The
L.E.D. will come ON solid.
To take the system o u t o f valet mode:
1. Turn the ignition key to the IGNITION ON (RUN) position.
2. Within 3 sec., press and release the valet button (the L.E.D. will come OUT).
3. The parking lights will flash twice to indicate that the vehicle is now in valet mode.
The L.E.D. will go out.
Note: Once valet mode is activated, the remote starter and alarm functions will be disabled.
Ignition Valet
This feature will allow you to remotely put your system into valet mode by using the ignition key
instead of the valet button as above. Ignition valet can be used without a valet button installed.
To put the system i n t o valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5times successively into
the IGNITION ON / RUN and OFF positions.
The parking lights will flash three times to indicate that the vehicle is now in valet mode. The L.E.D.
will come ON solid.
To take the system o u t o f valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5times successively into
the IGNITION ON / RUN and OFF positions.
The parking lights will flash twice to indicate that the vehicle is now in valet mode. The L.E.D. will
go out.
Note: With the remote valet activated, the remote starter and alarm functions will be disabled.
Remote Valet Mode
This feature will allow you to remotely put your system into valet mode by using the transmitter
instead of the valet button as above.
Getting into valet mode
•Hold the UNLOCK and START/STOP buttons simultaneously for 3 second.
•The parking lights will flash 3 times.
The LED will remain on solid.
Getting out of valet mode
•Hold the UNLOCK and START/STOP buttons simultaneously for 3 second.
•The parking lights will flash 2 times.
The LED will turn off.
“Home ValetTM” Mode
If configured at installation, this feature will remotely set the vehicle to a no-remote-start mode: if
the vehicle is parked indoors there is no danger of it starting accidentally by remote control.
Note: Once the home valet mode is activated, the vehicle will not start by remote.
To take the system i n t o home valet mode:
•Press the LOCK or UNLOCK button.
•Within 3 seconds, press the LOCK and START/STOP buttons simultaneously until the
parking lights go out
To take the system o u t o f home valet mode:
•Turn the ignition key to the IGNITION ON (RUN) position.

P. 10 User Guide AS-2300TW
The system will warn you if someone attempts to start your vehicle while it stands in home valet
mode. The parking lights will:
1- Turn ON then OFF; then
2- Flash twice, pause; then
3- Flash twice again.
Panic Mode
Note: Panic mode can only be activated if the horn has been adequately configured by your
installer.
In an emergency situation, you can activate panic mode by pressing and holding the SHIFT button
for 3 seconds. If the vehicle is under a remote start, you can shutdown the engine, stop the horn
and lock your doors by pressing the LOCK button:
If the car is not running, you can stop the horn by pressing the LOCK or UNLOCK buttons but it will not
lock or unlock the doors.
Furthermore, the panic mode can be stop by activating one of the following three (3) features:
a) Remote valet (pressing UNLOCK and START/STOP for 3 seconds)
b) Ignition valet (turning the key inside the ignition switch from OFF to ON 5 times in a row)
c) By pressing the valet switch (if included).
Panic Mode will automatically shut down after 30 sec.
Quick LockoutTM
(Also called secure panic.) For fast protection in emergency situations, the system will LOCK all
doors when you press the brake pedal while you hear the sound signal. (Quick lockout is only
available when panic mode has been set off.)
Cold Weather Mode
When cold weather mode is active, the engine starts every 2 hours and runs for 4 minutes (or for 9
or 20 minutes with diesel engines). Cold weather mode automatically ends after 24 hours.
To enter Cold Weather Mode:
•Press the SHIFT button and then the START/STOP for 3 seconds.
•There will be two (2) beeps and the parking lights will flash three (3) times.
To exit Cold Weather Mode, do any one of the following actions:
•Open the hood.
•Start the engine by remote.
•Turn the ignition key to the IGNITION ON (RUN) position.
•Press the SHIFT button and then the START/STOP button for three seconds.
•There will be one (1) beep and the parking lights will flash once.
To verify whether the system is in cold weather mode:
Press and release the brake pedal:
If the vehicle is in cold weather mode, the parking lights will stay on while the pedal is pressed.
Advanced Features: Installation-programmable Options
The remote starter was designed with flexibility and OEM integration in mind. With its program-
mable options, this unit can single-handedly control nearly any electrical system in your vehicle.
Caution: The programming of your system should be left to a professional. Changing any
one of the settings may affect the operation of your remote starter.
The installation-programmable options are as follows:
Remote Door Locks
Priority Door Access Ignition Re-lock Secure Lock