AV AVQ270 User manual

User Manual
23231 E La Palma Ave, Yorba Linda, CA 92887
Tel: [phone] | Fax: [phone]
Email: [e-mail]
Website: www.atronvision.com
If you have any further queson or need help, please contact our technical support.
1-866-974-8282 (9am – 5pm PST, Mon – Fri)
Please visit atronvision.com for full user manual and FAQs.
On choosing friends:
“Life is too short to hang out with people who aren’t resourceful.”

BEFORE USING THE PRODUCT
Thank you for purchasing our product. Our product features high resoluon for opmum Response
Time. This allows our customers to enjoy acon and gaming media to maximum potenal.
• Before using this product, please read quick Setup guide book for installaon.
• Please keep this guide book accessible for future reference.
WARNING
• Do not expose this product to direct sunlight, heat, or any hot object. Otherwise, the product life
span may be reduced, or fire may result.
• Do not let water enter the DC power device or get the device wet.
- This may cause a fire or an electric shock as a result.
- Avoid using product outdoors where it can be exposed to rain or snow.
- Be careful not to get the DC power adapter wet, including while washing the floor.
• Ensure the vents are not blocked by tablecloths or curtains.
- This may cause a fire as a result from increased internal temperature.
• If the product generates a strange noise, a burning smell, or smoke, remove the power cord immedi-
ately and contact Customer Service Center.
- This may cause a fire or an electric shock as a result.
• Do not insert a metallic object(paperclip, coin, hair pin, etc.) or inflammable object(paper, match, etc.)
into the vent or ports of the product.
- If water or any foreign substance enters the product, be sure to power off the product, remove
the power cord, and contact Customer Service Center. Product failure, an electric shock, or fire
may result.
• Avoid installing the product in a narrow space with bad venlaon, such as bookshelf or wall closet.
- Otherwise, a fire may result due to an increased internal temperature from poor venlaon.
• When installing the product on the wall it is recommended to contact a professional company for
installaon.
- The product may fall and break or cause personal injury if installaon of the wall mount is faulty.
• Do not install the product in a vehicle or place exposed to dust, moisture, oil, or smoke.
- An electrical shock or fire may result.
• Do not use or keep combusble spray or a flammable substance near the product.
- An explosion or fire may result.
• Do not hold the monitor upside down or move it by holding the stand.
- The product may fall and break or cause a personal injury.
• Do not touch the power plug with wet hands.
- Otherwise, an electrical shock may result.
• During a lightning or thunderstorm, power off the product and remove the power cable.
- An electrical shock or fire may result.
• Do not use a damaged power cord, damaged plug, or loose power outlet.
- An electrical shock or fire may result.
• Do not plug many products into the same electrical outlet.
- Otherwise, the outlet may overheat and could cause a fire or power surge to the device.
• Do not aempt to disassemble, repair, or modify the product on your own.
- An electric shock or fire may result.
• Do not bend or pull the power cord with force. Do not weigh the power cord down or apply any un-
necessary pressure. Do not li product by the power cord.
- A damaged power cord may cause an electric shock or fire.
• Do not put the DC power adapter near to any heang apparatus.
- Otherwise, a fire may result.
• Wipe the monitor screen with a clean, so and dry cloth. Wet a so and dry cloth in water and wring
thoroughly to clean the exterior of the monitor.
- Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor.
- Do not spray water or detergent directly on the product.

• LOS : Select “Line of Sight” Mode
• HOT : HOT Key
• SOURCE : Select Screen Mode
• MENU : Menu OSD (On Screen Display) Buon
• VOL / ◀ / ▼ : Volume Buon, Down Key
• 4:3 / ▶ / ▲ : Adjust Aspect Rao Buon, Up Key
• POWER : Monitor Power On/Off Buon
* The above specificaons are funon to change withoutnoce to improve quality.
* If any components are missing, then please contact the dealer where you purchased the product. The appearance of the
components may differ from the images shown. Components may vary depending on the country.
CHECKING THE COMPONENTS PARTS
BASIC MODEL
Monitor and Stand Base Dual-Link DVI Cable
Power Cable and DC Power Adapter Audio Cable
Quick Setup Guide
Remote Controller (Opon)

MAIN MENU
Press the MENU buon on the control panel to acvate the OSD menu window.
OSD MANUAL
OSD
50
50
BRIGHTNESS
CONTRAST
ECO [HOT KEY]
DCR
LOS
GAME 1
OFF
LOS 1
BRIGHTNESS
1. BRIGHTNESS
Press the ◀and ▶ to sdjust the posion of selected funcon.
- BRIGHTNESS : Adjust display brightness
- CONTRAST : Adjust display contrast
- HOT KEY : To set up applicaon mode
[STANDARD / TEXT / MOVIE / GAME(1, 2, 3) / ECO
/ Low Blue Light(1, 2, 3)]
- DCR : Dynamic cotrast ON/OFF
- LOS : To choose LOS(Line of Sight) funcon [LOS1 / LOS2 / LOS3]
2. IMAGE
Press the ◀and ▶ to sdjust the posion of selected funcon.
- H . POSITION : Adjust the images horizontal posion
- V . POSITION : Adjust the images vercal posion
- CLOCK : Adjust the image clock to reduce the vercal noise
- PHASE : Adjust the image phase to reduce the horizontal noise
- ASPECT : Adjust the images aspect rao
[AUTO / WIDE SCREEN / 4:3]
OSD
50
50
50
50
IMAGE
H . POSITION
V . POSITION
CLOCK
PHASE
ASPECT WIDE

OSD MANUAL
3. COLOR TEMP .
Press the ◀and ▶ to sdjust the posion of selected funcon.
- COLOR TEMP : To choose color temperature
- RED : Fine-tune red color temperature
- GREEN : Fine-tune green color temperature
- BLUE : Fine-tune blue color temperature
4. OSD SETTING
Press the ◀and ▶ to sdjust the posion of selected funcon.
- LANGUAGE : To choose the language in OSD menu
- OSD H . POS : Adjust OSD horizontal posion
- OSD V . POS : Adjust OSD vercal posion
- OSD TIMER : Adjust OSD display me
- TRANSPARENCY : Adjust OSD transparency
OSD
50
50
50
COLOR TEMP .
NORMALCOLOR TEMP .
RED
GREEN
BLUE
OSD
50
50
50
50
OSD SETTING
LANGUAGE
OSD H . POS .
OSD V . POS .
OSD TIMER
TRANSPARENCY

OSD MANUAL
5. RESET
Press the ◀and ▶ to sdjust the posion of selected funcon.
- IMAGE AUTO ADJUST : Automacally adjust the image horizontal/vercal posion
focusing and clock
- COLOR AUTO ADJUST : To adjust the color white balance
- RESET : Restore to factory sengs
- AUTO POEWRDOWN : Auto power down when no signal
[ON / OFF]
6. MISC
Press the ◀and ▶ to sdjust the posion of selected funcon.
- SIGNAL SOURCE : VGA (Analog) signal input
HDMI (Digital) signal input
- AUDIO SELECT : To choose audio type
[ANALOG / DIGITAL]
- VOLUME : Speaker volume adjustment (with audio)
OSD
50
VGA
MISC
SIGNAL SOURCE
AUDIO SELECT
VOLUME
OSD
RESET
IMAGE AUTO ADJUST
COLOR AUTO ADJUST
RESET
AUTO POWERDOWN OFF

TROUBLESHOOTING GUIDE
To perform self-troubleshoong please review the following condions that you may be experiencing.
• Power on the product.
• Disconnect the cable from the product.
• If the message NO SIGNAL appears, the product is working normally.
There is no sound.
• Check the connecon of the power cable or audio cable.
• Check the power switch, turn ON/OFF.
• Check the volume.
• Check the PC audio volume.
There is no image or image is displayed in black and white only.
• Adjust Brightness and Contrast.
• Check the cable connecon to PC.
The screen appears to shake or flicker and sound is unstable.
• Remove any accessories (video extension cable, etc.) and try again.
• Change the sengs or check the resoluon.
The DC power adapter is hot.
• This is a result of a product with the adapter or may be the result of a defecve product. Contact
Customer Service Center or purchase a new DC power adapter.
No Signal.
• Check that the cable is properly connected to the product.
• Check that the device is connected to all cables correctly and is powered on.
The screen is too bright or too dark.
• Press MENU buon, go to SETTINGS and FACTORY RESET.