Aventura MON-LCD19BL-CCTV User manual

MON-LCD19BL-CCTV
Reference Manual




1. Read all of these instructions.
2. Save these instructions for later use.
3. Unplug this monitor from the
wall outlet before cleaning. Do not
use liquid cleaners or aerosol
cleaners. Use a damp cloth for
cleaning.
4. Do not use attachments not recommended by
the monitor manufacturer as they may cause
hazards.
5. Do not use this monitor near water, e.g., near a
bathtub, washbowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool, etc.
6. Do not place this monitor on an
unstable cart, stand, or table. The
monitor may fall, causing serious
injury to a child or adult, and
serious damage to the appliance.
7. Slots and openings in the
cabinet and the back or bottom are
provided for ventilation, to ensure
reliable operation of the monitor,
and to protect it from overheating.
These openings must not be blocked or covered.
The openings should never be blocked by
placing the monitor on a bed, sofa, rug, or other
similar surface. This monitor should never be
placed near or over a radiator or heat register.
This monitor should not be placed in a built-in
installation such as a bookcase unless proper
ventilation is provided.
8. This monitor should be operated
only from the type of power source
indicated on the marking label. If
you are not sure of the power
supplied to your home, consult
your monitor dealer or local power company.
9. This monitor is equipped with a
3-wire grounding-type plug, That
is, a plug having a third
(grounding) pin. This plug will
only fit into a grounding-type
power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet.
Do not defeat the purpose of the grounding-type
plug.
10. Do not allow anything to rest
on the power cord. Do not locate
this monitor where the cord will be
abused by people walking on it.
11. Follow all warnings and instructions marked
on the monitor.
IMPORTANT SAFEGUARDS
12. For added protection for this
monitor during a lightning storm,
or when it is left unattended and
unused for long periods of time,
unplug it from the wall outlet. This
will prevent damage to the monitor and/or the
computer due to lightning and power line surges.
13. Do not overload wall outlets and extension
cords as this can result in fire or electric shock.
14. Never push objects of any kind into this
monitor through cabinet slots, as they may touch
dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the monitor.
15. Do not attempt to service this
monitor yourself, as opening or
removing covers may expose you
to dangerous voltages or other
hazards. Refer all servicing to
qualified service personnel.
16. Unplug this monitor from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
a. When the power cord or plug is damaged or
frayed.
b. If liquid has been spilled into the monitor.
c. If the monitor has been exposed to rain or
water.
d. If the monitor does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore normal operation.
e. If the monitor has been dropped or the cabinet
has been damaged.
f. When the monitor exhibits a distinct change in
performance, this indicates a need for service.
17. When replacement parts are
required be sure the service
technician has used replacement
parts specified by the manufacturer
that have the same characteristics as
the original part. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
18. Upon completion of any service or repairs to
this monitor, ask the service technician to
perform routine safety checks to determine that
the monitor is safe to operate.

WARNING: FOR CONTINUED SAFETY, REPLACE POWER ADAPTOR ONLY WITH
MANUFACTURER'S RECOMMENDED MODELS
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
NOTE :This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio or monitor technician for help.
CAUTION :Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’sauthority to operate the
equipment.
CANADIAN NOTICE
AVIS CANADIEN
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la Class B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
European Union Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the
the Low Voltage Directive (73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following European Norms (in
brackets are the equivalent international standards):
•EN55022 (CISPR 22) - Electromagnetic Interference
•EN55024 - Immunity Test for ITE Product
•EN60950 (IEC950) - Product Safety
•EN61000-3-2 (IEC555-2) - Power Line Harmonics

CONTENTS
CONTENTS
Introduction ............................................................................. 1
Product Features ................................................................. 2
Setup ......................................................................................... 3
Stand Assembling Procedures ............................................ 3
Connecting the 15 Pin Signal Cable and Power Cord ......... 4
Connecting the others ............................................................. 5
Operation & Adjustment ....................................................... 6
Specifications ......................................................................... 16
Factory Preset Timings ......................................................... 18
Monitor rotation (Optional).................................................. 19
Changing the Stand ............................................................... 20
Troubleshooting ..................................................................... 22

This manual explains how to correctly install, operate and get the
best performance from your monitor. Please read this user’s
guide carefully before installing your monitor, then keep it near
your monitor for quick reference.
First, please check that the contents of the box corresponds with
the following checklist :
•TFT LCD monitor
•Power cord
•RCA Cable
•15 pin signal cable
•User’s guide
•Audio Cable (Optional)
•DVI Cable(optional)
•AC Adapter
If any item is missing or damaged, please contact your dealer.
Please keep the box and packing materials so that you may
properly store or transport your monitor.
English - 1
INTRODUCTION
INTRODUCTION

English - 2
PRODUCT FEATURES
The monitor is designed for use in a small work area or for
those who need more work space on the desk.
The convenient and user-friendly on-screen display allows for
easy and accurate adjustments of screen size, position and
screen color.
The monitor complies with the VESA Display Data Channel
(DDC) specification for Plug and Play compatibility.
Advanced microcircuitry makes setup and configuration fast
and effortless.
The monitor features Advanced Color Controls for fine-tuning
to meet your own personal tastes or application requirements.
Use the on-screen controls to adjust the color temperature,
RGB gain value for the best possible screen color and intensity.
Press the menu button and activate the Self-Diagnosis menu to
determine whether your monitor is functioning normally, not
receiving a signal or is receiving a signal that is out of scanning
range.
Activate the higher refresh rates of the monitor to stabilize the
screen and eliminate the annoying flicker that contributes to
eye-strain and headaches.
The monitor supports the optimal display performance with
1280x1024 at 75Hz.
The monitor can be connected to various types of video devices
with supporting video input signals like Composite
video(CVBS), Seperate video.
The internal stereo speakers make the end user enjoy audio
sound.
With the POWER LIGHT function added,you can enjoy the
bright screen for movie or any other multimedia utilization.

English - 3
SETUP
SETUP
•The monitor is packed with stand and main body separated.
•Please join the stand with the main body before use.
Put some smooth pad or cloth on the
level surface and place the monitor
on it with the face downward.
Join the stand with the metal
protrusion from the bottom of the
monitor’s main body.
Tighten the screw fully at the
bottom of the stand by turning it
clockwise three to four turns.
※lAfter fully tightening the screw, bend the
knob of the screw onto the bottom of the
stand.
※lWhen disassembling the stand, please follow the procedure of assembling
in reverse order.
Caution :Incomplete tightening of the
screw may cause the
monitor unstable.
1
3
2
Stand Assembling Procedures

English - 4
CONNECTING THE 15 PIN SIGNAL CABLE AND POWER CORD
Turn off the computer and monitor.
Connect the 15 pin signal cable to the output port of the video card in
your computer and monitor.
Connect the DVI cable to the output port of the video card in your
computer and monitor. (Optional)
Connect the audio cable to the output port of the sound card in your
computer. (Optional)
Plug the DC jack into the DC in port located on the back of the monitor.
Plug the power cord into the AC receptacle of the Adapter.
Plug the other end of the power cord into the AC outlet.
DC 12V
VIDEOOUT
IN STEREO OUT
L AUDIO RIN

English - 5
DC 12V STEREOIN OUT
INOUT VIDEO L RAUDIO
123
CONNECTING THE OTHERS
1. Plug the connector to the BNC port on the rear of the
monitor (ex : Camcorder, VCR, DVD, ---).
2. Plug the connector to AUDIO INPUT port on the rear of the
monitor (ex : Computer, CD Player, ---).
3. Plug the connector to AUDIO OUTPUT port on the rear of
the monitor (ex : Speaker, Headphone, ---).
2
1
3
1. Turn on monitor.
2. Choose “VIDEO” connected to DVD player, using buttons of
remote controller or SOURCE button from exterior
adjustment buttons.
3. Put tape or DVD into VCR or DVD player and play.
How to watch DVD, VIDEO

English - 6
OPERA
OPERATION & ADJUSTMENT TION & ADJUSTMENT
CONTROL PANEL (Case #1)
POWER Indicator
1
3
4
Adjusts volume up and after
pressing MENU, adjusts
menu settings
Adjusts volume down and after
pressing MENU, adjusts menu
settings
Volume adjust
Volume adjust
Source
Up
8
6
Moves from top menu to
submenu in the OSD window
and opens the function window
for the selected icon.
While the OSD screen off,
selects input source and after
pressing SOURCE sets menu
functions.
Menu
5
Turns the OSD window on.
Turns the OSD (On-Screen
Display) window offand moves
from sub menu to top menu in
the OSD window.
Selects Menu.
While the OSD screen off,
turns the sound on & off.
Down
7
Selects menu.
While the OSD screen off,
launches the AUTOTRACKING
function directly. (Analog mode)
Switches the monitor on
and off.
POWER
2
Shows both normal operation and power management status with
power indicator light.
Sensor window
Remote control. Receives signal from the Remote controller

English - 7
CONTROL PANEL (Case #2)
Shows both normal operation and power management status with
power indicator light.
POWER Indicator
1
3
4
Adjusts volume up and after
pressing MENU, adjusts
menu settings
Adjusts volume down and after
pressing MENU, adjusts menu
settings
Volume adjust
Volume adjust
Source
Up
8
6
Moves from top menu to
submenu in the OSD window
and opens the function window
for the selected icon.
While the OSD screen off,
selects input source and after
pressing SOURCE sets menu
functions.
Menu
5
Turns the OSD window on.
Turns the OSD (On-Screen
Display) window off and moves
from sub menu to top menu in
the OSD window.
Selects Menu.
While the OSD screen off,
turns the sound on & off.
Switches the monitor on
and off.
Sensor window
Remote control. Receives
signal from the Remote
controller
POWER
2
Down
7
Selects menu.
While the OSD screen off,
launches the AUTOTRACKING
function directly. (Analog mode)

English - 8
KEY PROCESS
To select MENU press the MENU button.
Use up- down button to select the main menu.
Use SOURCE button to select the sub menus on the right.
Use up-down buttons to select sub-menu function.
Press SOURCE button, then using left-right buttons you can make
adjustments as necessary
To exit press MENU.

English - 9
HOT KEY
When there is no OSD, if you press this ▼
(Down/AUTO) button, you can use the best
displayperformance fit for a current mode.
(Analog MODE)
Selects signal in order.
ANALOG - DIGITAL - VIDEO
When there is no OSD, if you press this ▲
(UP/MUTE) button, you can turns the sound
on and off.
When there is no OSD, you can adjust the
volume directly.

English - 10
ADJUSTMENT PROCEDURE
No Raster
Adjust the CLOCK control.
Perform the
H-POSITION
Perform the Auto
tracking
Is the H.SIZE proper?
Is the noise displayed on
the screen?
Adjust the CLOCK until
the screen is cleared.
Is the noise displayed on
the screen yet?
Yes
Yes
No
No
End
Yes

English - 11
Color
Function
OSD FUNCTIONS WITH USING ANALOG MODE
Choose different preset color temperatures or set your
own customized color parameters.
Color Temp.
Adjust the position of the display horizontally (left or
right) and vertically (up or down).
H.Position &
V.Position
Remove any horizontal noise and clear or sharpen the
image of characters.
Adjust the width (horizontal size) of the screen
image.
Phase
Clock
Adjust the display image quality (if the screen
proceed to scaling up).
Sharpness
Choose automatically the proper horizontal position,
vertical position & size of the screen image.
Auto Adjust
OSD
Adjust the color.
Color Adjust
Adjust the contrast of image, the difference between
light and dark areas on the screen.
Contrast
Adjust the brightness of image.
Brightness
Automatically eliminate any image shaking.
Auto Colour
Picture
OSD
OSD

English - 12
OSD Menu
Misc.
Adjust the OSD Transparency.
Translucent
Select language for OSD.(English/한국어)
Language
Adjust the OSD position horizontally (left or right)
and vertically (up or down).
OSD H & V
Pos.
Adjust the display OSD time.
OSD Timer
Select input signal source. (D-SUB/DVI/CVBS)
Signal Source
Select powerlight mode(PC/Game/Movie)
Mode
Reset the screen to the Factory Preset
Display Settings.
Reset
Sound
Turn the audio sound on or off.
Sound
Increase or decrease audio volume.
Volume
OSD
OSD
OSD

English - 13
OSD FUNCTIONS WITH USING VIDEO/DIGITAL MODE
Adjust the display image quality (if the screen
proceed to scaling up).
Sharpness
Adjust the contrast of image.
Contrast
Adjust the brightness of image.
Adjust saturation of image.
Brightness
Saturation
Adjust the hues of image.
Hue
Color
OSD
MISC.
Select input signal source. (D-SUB/DVI/CVBS)
Signal
Source
Select powerlight mode(PC/Game/Movie)
Mode
Reset the screen to the Factory Preset Display
Settings.
Reset
OSD MENU
Adjust the OSD transparency
Translucent
Select language for OSD.(English/한국어)
Language
Adjust the OSD position horizontally (left or right)
and vertically (up or down).
OSD H & V
Pos.
Adjust the display OSD time.
OSD Timer
OSD
OSD

English - 14
SOUND
Turn the audio sound on or off.
Sound
Increase or decrease audio volume.
Volume
OSD

English - 15
SELF DIAGNOSIS
If there is no image, the Self Diagnosis screen will be displayed.
Self Diagnosis function checks if the status of the monitor screen
is No Signal, Out of range or None support.
No Signal screen is displayed when the D-
Sub signal connector is connected but the
status of the monitor is on DPMS mode.
Out of Range screen is displayed when the
applied frequency is under or over normal
range.
Normal range
(Non-interlaced mode only)
H : 30 - 80 KHz
V : 56 - 77 Hz
Check cable screen is displayed when the
Analog signal cable is disconnected.