AVIC Optoelectronics TMS150XG1-10TB User manual

TM-SA-A0001-03-E 1/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
AVIC Confidential
confidential

TM-SA-A0001-03-E 2/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
INTRODUCTION
• WARRANTY
Shanghai AVIC OPTOELECTRONICS Co. Ltd (hereinafter called "AVIC") warrants that this product meets the
product specifications set forth in this document. If this product under normal operation is found to be
non-conforming to the product specifications, and such non-conformance is promptly notified to AVIC within one (1)
year after the delivery date, and further such non-conformance is solely attributable to AVIC, AVIC shall repair the
non-conforming product or replace it with a conforming one, free of charge. However, this warranty does not apply
to any non-conformance that can be found easily by incoming inspections or those resulting from any one of the
following：
1) Unauthorized or improper repair, maintenance or modification
2) Operation or use against specifications, instructions or warnings given by AVIC
3) Any other causes attributable to customer
In case AVIC repairs or replaces a product after the one (l)-year warranty period, AVIC shall be entitled to charge
for such repair or replacement. Those replaced parts shall be covered with six (6)-month warranty period from the
replacement day. Non-conforming products may be replaced with substitutes instead of repair when the manufacture of
this product has been terminated.
EXCEPT AS EXPRESSLY SET FORTH HEREIN, AVIC DISCLAIMS ANY WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND DISCLAIMS ANY REMEDIES.
• MAINTENANCE
The specifications of maintenance parts may be partially changed within equivalent quality or better. In this
product, AVIC will not accept to maintain for only mounting parts on circuit board (e.g. connector, fuse, capacitor,
resistor, etc.) and only backlight conformation parts (e.g. reflector sheet, light guide plate, etc.).
If AVIC is planning discontinuation for this product, AVIC shall inform it to customers in six (6)-months advance
from the issued date of official agreements. In addition, after product discontinuation, AVIC may replace substitutes
instead of maintenance parts with whole product.
• CHANGE CONTROL
For the purpose of product improvement, this product design may be changed for specifications, appearance, parts,
and circuits and so on. In case a design change is affected on the product specifications, AVIC shall inform it to
customers in advance.
•HANDLING OF DOUBTFUL POINTS
Any question arising out of, or in connection with, this SPECIFICATION or any matter not stipulated herein will be
settled each time upon consultation between both parties.
confidential

TM-SA-A0001-03-E 3/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
CONTENTS
INTRODUCTION......................................................................................................................................................... 2
CONTENTS.................................................................................................................................................................. 3
RECORD OF REVISION………………………………………………………………………….………………….4
1. OUTLINE ................................................................................................................................................................. 5
1.1 STRUCTURE AND PRINCIPLE ................................................................................................................. 5
1.2 APPLICATIONS ........................................................................................................................................... 5
1.3 FEATURES ................................................................................................................................................... 5
2. GENERAL SPECIFICATIONS ................................................................................................................................ 6
3. ABSOLUTE MAXIMUM RATINGS……………………………………………………………………………....7
4. BLOCK DIAGRAM ................................................................................................................................................. 8
5. MECHANICAL SPECIFICATIONS ........................................................................................................................ 9
6. ELECTRICAL CHARACTERISTICS ..................................................................................................................... 9
6.1 DRIVING FOR LCD………………………………………………………………………………………..9
6.2 DRIVING FOR BACKLIGHT…………………………………………………………………………….10
7. CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS…………………………………………………11
7.1 LCD PANEL SIGNAL PROCESSING PINS……………………………………………………………..11
7.2 BACKLIGHT LAMP…………………………………………… ………………………………………..12
7.3 POSITION OF PLUGS AND A SOCKET………………………………………………………………..12
7.4 CONNECTION BETWEEN REVIEVER AND TRANSMITTER FOR LVDS………………………….13
8. DISPLAY COLORS AND INPUT DATA SIGNALS……………………………………………………………..14
9.INTERFACE TIMING……………………………………………………………………………………………..15
9.1 TIMING CHARACTERISTICS…………………………………………………………………………..15
9.2 INPUT SIGNAL TIMING CHART……………………………………………………………………….16
9.3 PIXEL DATA ALIGNMNET OF DISPLAY IMAGE……………………………………………………..16
9.4 POWER SUPPLY VOLTAGE SEQUENCE .............................................................................................. 17
10. OPTICS................................................................................................................................................................. 19
11. MARKINGS.......................................................................................................................................................... 21
11.1 PRODUCT LABEL................................................................................................................................... 21
11.2 OTHER MARKINGS ............................................................................................................................... 22
11.3 INDICATION LOCATIONS..................................................................................................................... 22
12. PACKING, TRANSPORTATION AND DELIVERY ........................................................................................... 23
13. PRECAUTIONS ................................................................................................................................................... 25
13.1 MEANING OF CUTION SIGNS ............................................................................................................. 25
13.2 CAUTIONS............................................................................................................................................... 25
13.3 ATTENTIONS........................................................................................................................................... 25
14.OUTDRAWING..................................................................................................................................................... 27
confidential

TM-SA-A0001-03-E 4/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
Record of Revision
Rev Issued Date Description Editor
1.0 2009-12-22 Preliminary Release Hyman Chen
2.0 2010-06-01
Add “Operation life time, Differential input voltage” Hyman Chen
3.0 2010-7-7 LVDS interface (6 bit+HIFRC) revise James Xiao
confidential

TM-SA-A0001-03-E 5/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
1. OUTLINE
1.1 STRUCTURE AND PRINCIPLE
TMS150XG1-10TB module is composed of the amorphous silicon thin film transistor liquid crystal display
(a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight. The
a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT array glass
substrate and a color-filter glass substrate.
Color (Red, Green, Blue) data signals from a host system (e.g. PC, signal generator, etc.) are modulated into
best form for active matrix system by a signal processing board, and sent to the driver LSIs which drive the individual
TFT arrays. The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight
assembly, when it is controlled by data signals. Color images are created by regulating the amount of transmitted light
through the TFT array of red, green and blue dots.
1.2 APPLICATIONS
• Monitor for PC（for amusement or industry）
1.3 FEATURES
• a-Si TFT active matrix
• LVDS interface (6 bit+HIFRC)
• Wide viewing angle
• High response time: 8ms (typ.)
• PSWG standard
• High contrast: 600:1(typ.)
• Edge light type backlight (Inverter less)
• ROHS compliance
• TCO’03 compliance
confidential

TM-SA-A0001-03-E 6/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
2. GENERALSPECIFICATIONS
Display area 304.128 (W) x 228.096 (H) mm (typ.)
Diagonal size of display 38.0 cm (15.0 inches)
Drive system a-Si TFT active matrix
Display color 16,777,216 colors (6bit+HIFRC)
Pixel 1,024 (H) x 768 (V) pixels
Pixel arrangement RGB vertical stripe
Dot pitch 0.099 (W) x 0.297 (H) mm
Pixel pitch 0.297 (W) x 0.297 (H) mm
Module size 326.50±0.5 (W) x 253.5±0.5 (H) x 11.13±0.5 (D) mm (typ.)
Weight 1000 g (typ.)
Contrast ratio 600:1 (typ.)
Viewing angle 160°/ 160° (typ.)
Color gamut 60 % (typ.)
Response time 8 ms (typ.)
Luminance 250cd/m2(typ.)
Tran missive Mode Normally White
Surface Treatment AG Type
Signal system LVDS 1port
Power supply voltage LCD panel signal processing board：3.3V
Backlight 2 cold cathode fluorescent lamps
Power consumption (10.1 )W (typ.)
confidential

TM-SA-A0001-03-E 7/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
3. ABSOLUTE MAXIMUM RATINGS
Parameter Symbol Rating Unit Remarks
Power supply
voltage LCD panel signal board VDD -0.3 ~ +3.6 V Ta = 25℃
Display signals
Note1
Input voltage
for signals Function signals
Note2
Vi
-0.3 ~ +3.6
and
Vi<VCC +0.3
V Ta = 25℃
Storage temperature Tst -20 ~ +60 ℃Note3
Operating temperature Top 0 ~ +55 ℃Note3，4
Absolute humidity AH 70 g/m3Ta > 55℃
Operating altitude - ≤4,850 m 0°C≤Ta≤55°C
Storage altitude - ≤13,600 m -20°C≤Ta≤60°C
Note1: Display signals are D0+/-, D1+/-, D2+/-, D3+/- and CK+/-.
Note2: Function signal is MSL.
Note3: Temperature and relative humidity range is shown in the figure below.
(a) 90%RH Max. (Ta ≤40℃)
(b)Web-bulb temperature should be39℃Max.(Ta＞40℃)
(c) No condensation.
Note4: The temperature of panel display surface area should be 0℃Min and 60℃Max.
-40 -20 0 20 40 60 80
5
20
40
60
80
Operating Range
Storage Range
Relative Humidity（％RH）
Temperature ℃
confidential

TM-SA-A0001-03-E 8/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
4. BLOCK DIAGRAM
Note1: Connections between GND, FG (Frame ground) and VBLC (Lamp low voltage terminal) in the product
GND - FG Connected
GND - VBLC Not connected
FG - VBLC Not connected
Note2: These grounds should be connected together in customer equipment.
D0-
D0+
D1-
D1+
D2-
D2+
CLK-
CLK+
D3-
D3+
MSL
VDD
VBLH1/2
VBLC2/2
LCD MODULEI/F
FUSE
DC/DC
Converter
Power
LCD Panel
H:1024×3（R,G,B）
V: 768
Gate Driver
Source Driver
Edge side backlight
LVDS Receiver
T
i
m
i
n
g
c
o
n
t
r
o
l
l
e
r
100Ω
100Ω
100Ω
100Ω
100Ω
confidential

TM-SA-A0001-03-E 9/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
5. MECHANICAL SPECIFICATIONS
Parameter Specification Unit
Module size 326.5±0.5 (W) x 253.5±0.5 (H) x 11.13±0.5 (D) mm
Display area 304.128 (W) x 228.096 (H) mm
Weight 1000 (typ.) g
6. ELECTRICAL CHARACTERISTICS
6.1 Driving for LCD panel signal processing board
Parameter Symbol min. typ. max. Unit Remarks
Power supply voltage VDD 3.0 3.3 3.6 V -
Power supply current IDD - 500Note1 700Note 2 mA at VDD = 3.3V
Permissible ripple voltage VRP - - 100 mV VDD
Differential input voltage ︱Vid︱ 200 - 600 mV -
Low VTL -100 - mV
Differential input threshold
voltage for LVDS receiver High VTH - - 100 mV
at VCM = 1.2V
Note3
Input voltage width for LVDS receiver Vi 0 - 2.4 V -
Terminating resistor RT - 100 - -
Rush current Irush - - 2.0 A Note4
Note 1: Checkered flag pattern (EIAJ ED-2522);
Note 2: 2H1V dot inverse pattern
Note 3: Common mode voltage for LVDS receiver
Note4: Measurement Conditions:
Q2
MOSFET- N
2
3
1S2
SW -SP DT
1uF/16V
C2
Cap
GND
GND
5V
F1
Fu se ( 2A )
20K
R3
5V
1K
R2
47K
R1
10uF/16V
C3
Ca p
12V
Q1
MOSFET-N
1uF/16V
C1
Ca p
VDD
GND
confidential

TM-SA-A0001-03-E 10/29
Not duplication without authorization Shanghai AVIC OPTOELECTRONICS Co. Ltd
6.2 Driving for backlight lamp
Parameter Symbol min. typ. max. Unit Remarks
Lamp voltage VBLH 549 610 671 Vrms For each lamp
Lamp current IBL 3.5 7.0 7.5 mArms at L = 250cd/ m2(typ.)
- - 1600 Vrms Ta = 0℃Note2Lamp starting voltage
Note1 VS - - 1100 Vrms Ta = 25℃Note2
Oscillation frequency FO 40 50 60 kHz Note3
Operation life time Hr 40,000 - - Hour
Ta = 25℃
IBL = 7.0 mArms
Note4
Note1: The value is the characteristic of lamp. The starting voltage of inverter should be lower than the value. But the
possibility of not lighting exists by the lower voltage, so the suitable voltage should considered by the test.
Note2: The asymmetric ratio of working waveform for lamps (Lamp voltage peak ratio, Lamp current peak ratio and
waveform space ratio) should be less than 5% (See the following figure). If the waveform is asymmetric, DC
(Direct current) element applies into the lamp. In this case, a lamp lifetime may be shortened, because a
distribution of a lamp enclosure substance inclines toward one side between low voltage terminal (Cold
terminal) and high voltage terminal (Hot terminal).
Pa
Pb
Sa
Sb
|Pa - Pb| / Pb × 100 ≤5%
|Sa - Sb| / Sb × 100 ≤5%
Pa:
Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative
Sa: Waveform space for positive part, Sb: Waveform space for negative part
Note3: Recommended value of “FO” is as following.
FO = 1/4 x 1/th x (2n-1) n: Natural number (1, 2, 3 ……)
Note4: Lamp operating lifetime is mean time to half-luminance. In case the product works under low temperature
environment, the lifetime becomes short.
(Ta=25°C) Note1
confidential