AVLT-Power Non-VESA Monitor Adapter Kit for 13" to 27" LCD/LED Screen... User manual

1
Non-VESA Monitor Adapter Kit for
13" to 27" LCD/LED Screen Sizes
Installation Instructions
AP4-0021A
Weight Capacity: 8KG (17.6 lbs)

2
Specifications
Screen Size 13" to 27"
Rated Load 17.6 lbs (8 Kgs)
VESA compatible 75x75 / 100x100mm
Screens Thickness 1" to 1.79"
Material Steel/Plastic
Color Black
Product Weight 1.5 lbs
Product Dimension 14.78"x14.78"x1.57"
Unpacking
• Carefully remove the contents and lay them out on cardboard or other protective surface
• Check package contents against the parts list to ensure that all components were received
undamaged. Do not use damaged or defective parts
• Carefully read all instructions before attempting the installation
Safety Information
• Use proper safety equipment during installation
• If you don't understand the installation instructions, please consult an installation
specialist
• This product contains small parts which can act as a choking hazard if swallowed
• Do not use this product for any purpose or in any configuration not explicitly specified
in these instructions
Tools Required
• Phillips Screwdriver
B - (4x) Support C - (4x) Plastic Cap
A - (4x) Arm D - (8x) Nut E - (8x) Bolt
F - (4x) M6x40 Bolt G - (4x) M6x60 Bolt H - (4x) M6x80 Bolt I - (8x) Washer J - (1x) Wrench

3
Installation
Step 1) Assemble the Support Arm
1. Select Bolt (F/G/H) according to the depth of your monitor and use it to install Support
(B) onto Arm (A) using a Phillips screwdriver. Do not fully tighten until instructed to do
so, see Figure 1.
Figure 1
Step 2) Install the Support Arm to the VESA Plate
Note: Select one of the four the installation options that matches your monitor's backplate
surface.
2A) X-pattern: Suitable for all backplate surfaces. Use two sets of bolt/washer/nut to attach
each arm to the VESA plate.
1. Use Bolt (E), Washer (I) with Nut (D) and tighten using Wrench (J), see Figure 2. Note:
Do not fully tighten until instructed to do so in Step 3.
Figure 2

4
2B) Y-pattern: Suitable for all backplate surfaces. Use two sets of bolt/washer/nut to attach
the upper arms and one set of bolt/washer/nut to attach the lower arms to the VESA
plate.
1. Use Bolt (E), Washer (I) with Nut (D) and tighten using Wrench (J), see Figure 3. Note:
Do not fully tighten until instructed to do so in Step 3.
Figure 3
2C) Inverted Y-pattern: Suitable for flat and top backplate surfaces. Use two sets of bolt/
washer/nut to attach the lower arms and one set of bolt/washer/nut to attach the upper
arms to the VESA plate.
1. Use Bolt (E), Washer (I) with Nut (D) and tighten using Wrench (J), see Figure 4. Note:
Do not fully tighten until instructed to do so in Step 3.
Figure 4
J
D
I
E
J
D
I
E

5
2D) H-pattern: Suitable for flat backplate surfaces. Use one set of bolt/washer/nut to attach
the arms to the VESA plate.
1. Use Bolt (E), Washer (I) with Nut (D) and tighten using Wrench (J), see Figure 5. Note:
Do not fully tighten until instructed to do so in Step 3.
Figure 5
Step 3) Install the Monitor
1. Adjust the position of the Support Arms to match your monitor, then fully tighten
Nut (D) using Wrench (J) to secure them to the VESA plate, see Figure 2, 3, 4 or 5.
2. Tighten Bolt (F/G/H) finger tight using a Phillips screwdriver to secure Support (B)
to the monitor, see Figure 6.
3. Install Plastic Cap (C) onto Support (B), see Figure 6.
Figure 6
D
J
I
E
Bolt (F/G/H)
C
B
Maintenance
Check the mounting screws every month for tightness.

6
Blank page

7
Blank page

8
Warranty Statement
This warranty covers the original purchaser and guarantees the product to be free of any defects in
materials or workmanship for one (1) year from the date of purchase of the product.
Copyright Statement
Non-VESA Monitor Adapter Kit for 13-27" LCD/LED Screen Sizes is a trademark of AVLT-Power
Inc. All other trademarks are the property of their respective owners.
Lot Number
Please keep this LOT number for future product return, warranty or exchange.
Lot Number Part Number