Avonic AV-MT200 User manual

USER MANUAL
Avonic Wall Mount
AV-MT200, AV-MT220
www.avonic.com • © July 2022 • Version 1.1

DISCLAIMER AND CONTACT
Disclaimer
All text, graphics, photographs, trademarks, logos, artwork and computer code (collectively, “Content”),
including but not limited to the design, structure, selection, coordination, expression, “look and feel” and
arrangement of such Content, contained in this Manual is owned, controlled or licensed by or to Avonic, and is
protected by trade dress, copyright, patent and trademark laws, and various other intellectual property rights and
unfair competition laws.
Except as expressly provided in these Terms of Use, no Content of this Manual may be copied, reproduced,
republished, uploaded, posted, publicly displayed, encoded, translated, transmitted or distributed in any way
(including “mirroring”) to any other computer, server, Website or other medium for publication or distribution or for
any commercial enterprise, without the prior written consent of Avonic.
Copyright © 2022 AVONIC All Rights Reserved.
The information contained in this Manual is subject to change without notice.
Contact Info
For any questions or suggestions, contact your reseller or local distributor of Avonic.
Visit the Avonic website www.avonic.com to find your local Avonic distributor or to download the most recent
version of the documentation.
Join Avonic on Social Media
www.Facebook.com/avonicPTZ www.instagram.com/avonicPTZ
www.LinkedIn.com/company/avonic www.youtube.com/channels/avonic
www.twitter.com/avonic
ii

IMPORTANT INFORMATION
Liability
Avonic will NOT be held responsible for any damage or injury caused by unqualified persons carrying out these
tasks, or by not following the instructions in this Manual.
Intended Use and Non-Intended Use
Installation
The following applies to the installation of the mount and the camera:
• The installation activities described in this Manual should ONLY be executed by experienced
technicians.
• The installation activities should NOT be executed by minors, mentally disabled persons or other persons
not qualified to perform these tasks.
Operation
The following applies to the operation of the mount and the camera:
• The operational activities described in this Manual should ONLY be executed by people with enough
technical knowledge to perform the activities in a safe manner.
• This Product is specifically developed for video conferencing / streaming via internet by companies,
institutes and universities. It is NOT meant for private use in the residential area.
• This Product should ONLY be used indoors.
• This Product is NOT a medical device and should NOT be used as a substitute for professional medical
judgment. It is NOT designed or intended for use in the diagnosis of disease or other conditions, or in the
cure, mitigation, treatment, or prevention of any condition or disease. Please consult your healthcare
provider prior to making any decisions related to your health.
Important Precautions
This Product is NOT intended for use where failure of the device could lead to death, personal
injury, or severe environmental damage.
Failure to follow the SAFETY NOTES as described in this chapter could result in fire, electric
shock, injury, or damage to this Product or other property.
Power this Product ONLY with the included cable and power adapter. Other adapters
may not meet applicable safety standards, and could pose a risk of death or injury when
connected.
To prevent the risk of injury or damage to the Product or other property caused by a
potentially explosive atmosphere.
Be sure that you have COMPLETELY READ and UNDERSTOOD ALL information in this Manual
before unpacking, installing and using this Product. Keep the Manual in a safe place for
future reference or download it from www.avonic.com.
iii

Symbols Used in This Manual
Symbol Meaning Description
Danger Not following the instructions associated with this symbol may lead to
life-threatening situations and / or serious damage to the Product.
Warning Not following the instructions associated with this symbol may lead to
personal injury and / or serious damage to the Product.
Caution Caution should be exercised with the associated information.
Information The information associated with symbol refers to a general remark or
a reference to other documentation.
Instruction This symbol refers to one or more user instructions.
Recycling Specific parts of the Product can be re-used.
Acronyms
The following acronyms are used in this Manual:
PTZ Pan / Tilt / Zoom
SKU Stock Keeping Unit
UNC Unified National Coarse
iv

Contents
DISCLAIMER AND CONTACT................................................................................................................ ii
IMPORTANT INFORMATION.................................................................................................................. iii
Liability......................................................................................................................................... iii
Intended Use and Non-Intended Use......................................................................................iii
Installation..........................................................................................................................iii
Operation.......................................................................................................................... iii
Important Precautions......................................................................................................iii
Symbols Used in This Manual....................................................................................................iv
Acronyms.................................................................................................................................... iv
INTRODUCTION......................................................................................................................................6
Purpose of This Manual..............................................................................................................6
Target Audience.........................................................................................................................6
Document Structure................................................................................................................... 6
SAFETY INSTRUCTIONS........................................................................................................................... 7
Important Precautions................................................................................................................7
Intended Use...............................................................................................................................7
Handling.............................................................................................................................7
Mounting............................................................................................................................7
Ventilation..........................................................................................................................8
Repair................................................................................................................................. 8
PRODUCT OVERVIEW........................................................................................................................... 9
Description...................................................................................................................................9
Features....................................................................................................................................... 9
UNPACKING.........................................................................................................................................10
Package Contents................................................................................................................... 10
Unpacking the Mount..............................................................................................................11
Return Procedure..................................................................................................................... 11
MOUNTING AND INSTALLATION.........................................................................................................12
Mounting on a Wall................................................................................................................. 12
1. Baseplate.....................................................................................................................12
2. Mounting the Camera...............................................................................................13
3. Cable Cover............................................................................................................... 14
4. Cover Cap.................................................................................................................. 14
Mounting on a mounting pole............................................................................................... 15
Trussmount clamp and mounting pole........................................................................ 15
MEASUREMENTS AND SPECS MT200..................................................................................................16
General Specifications.............................................................................................................17
MEASUREMENTS AND SPECS MT220..................................................................................................18
General Specifications.............................................................................................................19
TRANSPORT AND STORAGE............................................................................................................... 20
DISPOSAL AND RECYCLING...............................................................................................................21
v

INTRODUCTION
Purpose of This Manual
This Manual describes the safety precautions and the instructions for safe unpackaging, installation, operation,
maintenance and disposal of the Avonic MT200 and MT220 Wall Mount.
Note that this is ONE manual for both mounts and that the mounts are separately sold. In this Manual the
Avonic MT200 and MT200 Wall Mount is referred to as the 'Product'.
If you want to use the mount and camera in combination with the CamDirector, you need to make sure
that the MT200 is NOT compatible in combination with such a system! Use the MT220 to do this.
Target Audience
This Manual is developed for installation technicians who install the Product at client sites, and for IT professionals
who are responsible for operating the Product.
Document Structure
The Manual is subdivided into the following Chapters:
1. Introduction
2. Safety
3. Product Overview
4. Unpacking
5. Mounting and Installation
6. Measurements and Specs MT200
7. Measurements and Specs MT220
8. Transport and Storage
9. Disposal and Recycling
6

SAFETY INSTRUCTIONS
This chapter contains important safety information regarding the unpacking, installation and use of the mount
and the camera.
Important Precautions
This Product is NOT intended for use where failure of the device could lead to death, personal
injury, or severe environmental damage.
Failure to follow the SAFETY NOTES as described in this chapter could result in fire, electric
shock, injury, or damage to this Product or other property.
Power this Product ONLY with the included cable and power adapter. Other adapters
may not meet applicable safety standards, and could pose a risk of death or injury when
connected.
To prevent the risk of injury or damage to the Product or other property caused by a
potentially explosive atmosphere.
Be sure that you have COMPLETELY READ and UNDERSTOOD ALL information in this Manual
before unpacking, installing and using this Product. Keep the Manual in a safe place for
future reference or download it from www.avonic.com.
Intended Use
See section Intended Use and Non-Intended Use on page iii for details.
Handling
To prevent the risk of injury, take the following precautions when handling this Product:
• Handle the Product with care. It is made of metal and plastic components.
• The Product can be damaged if dropped, burned, punctured or crushed, or if it comes into contact
with liquid.
• Do not pick up and move the Product unit while a tripod is attached. The fitting may break under the
weight of the tripod, which may result in injury.
• If you suspect any damage to the Product, discontinue its use, as it may cause injury.
Mounting
To prevent the Product from falling down which may cause injuries:
• Mount this Product to a wall or mounting pole.
• ONLY use an Avonic mount for mounting to a wall or mounting pole.
• Ensure the mounting construction is capable of supporting four times the weight of the Product. (See
'General Specifications > Weight product’ in the Product Datasheet for the exact weight.)
• Use a safety loop or drop protection that prevents the Product from falling if the mounting construction
fails.
• During installation, NEVER install a Product above a person.
• Check the installation at least once a year. An improper mounting could cause the unit to fall off,
resulting in personal injury.
7

Ventilation
To prevent the risk of life-threatening injury or damage to the Product or other property, caused by electric
shock or fire hazard due to overheating of the camera mounted on the Product:
• Maintain adequate ventilation by NOT installing or placing the Product unit in a bookcase, built-in
cabinet or any other confined space.
• Ensure that curtains or any other material does NOT obstruct the ventilation.
Repair
Take the following precautions if the Product should be repaired:
• Don’t open this Product and don’t attempt to repair it yourself. Disassembling the Product may
damage it or may cause injury to you.
• If this Product is damaged, malfunctioning, or if it comes into contact with liquid, contact Avonic or an
Avonic Authorized Service Provider.
• Repairs by service providers other than Avonic or an Avonic Authorized Service Provider may not
involve the use of Avonic genuine parts and may affect the safety and functionality of the device. You
can find more information about repairs and service at www.avonic.com.
8

PRODUCT OVERVIEW
Description
The Avonic MT220 and MT200 Wall Mount are both solid wall mounts suitable for the support of one or two CM40
or CM70 series PTZ cameras. Its discrete design matches the silent operation of Avonic PTZ cameras. The wall
mount is a beautiful extension that not only ensures great and safe support of the PTZ cameras, but also allows
for all the cables to be hidden inside the mount. Accessories include a heavy-duty 30mm steel ring specifically
designed to mount the MT-220 and/or MT-200 on a truss clamp. For mobile applications the MT220 and MT200 can
be mounted in a flight case or installed on a tripod. Also available in black to match our black PTZ cameras.
Features
The Avonic MT220 and MT200 are having the following features:
Camera support
Supports one or two CM40 or CM70 camera's.
Separate base and plate
Separate base and camera plate for hassle free mounting and cable installation.
Hands free installation
Hands free installation of the camera, only one screw needed to secure it.
Integrated
Integrated cable cover.
Design
Discrete and compact design.
Seamless integration
Seamless integration with the shape and color of Avonic PTZ cameras.
Accessories
Heavyduty 30mm steel ring specifically designed to mount the MT200 and MT220 on a truss clamp.
9

UNPACKING
This describes the contents of a complete Product package, and instructions for safe unpacking and (if
necessary) Product return.
It is subdivided into the following sections:
1. Package Contents
2. Unpacking the Camera
3. Return Procedure
Package Contents
The following tables contains an overview of the package contents of the Product.
Take note that the mounts are separately sold! Check only the package contents for the mount you
have.
No. Quantity Description Avonic SKU
MT200 MT220
1 1 pc 1 pc Wall Mount AV-MT200-B/ -W
AV-MT220-B/ -W
2 1 pc 3 pc Black 30MM Cover Cap -
3 1 pc 1 pc 30MM Steel Ring for Truss Mount -
4 1 pc 2 pc 1/4”- UNC Pozidrive screw (20mm) to fasten
camera
-
5 2 pc 2 pc M6*10mm Allen Bolt screw -
6 5 pc 8 pc M3*6mm DIN9785 Pozidrive screws -
Each item is visualized below and referenced by the associated number in the table above:
Package Contents MT200 Package Contents MT220
10

Unpacking the Mount
Execute the following steps to unpack the MT220 or MT200 mount and associated components:
1. Open the plastic bag.
2. Verify that the contents of the bag exactly matches the items as described in Package Contents on page
10. Check ONLY the packets contents for the mount you have! If the described items in the package contents
do not match, contact Avonic and stop here.
The mount should be in its protective foam as follows:
MT220 in plastic bag MT200 in plastic bag
3. Verify that the plastic mount bag is sealed. If this is NOT the case, contact Avonic and stop here.
4. Break the seal of the sealed mount bag.
5. Take the mount out of the bag.
6. Install the mount following the steps as described in the chapter MOUNTING AND INSTALLATION on page
12
Return Procedure
If, for any reason, you have to return the mount to Avonic, Execute the following steps:
1. Place the mount back in its protective foam and in horizontal position in the bag!
2. Place the mount with all of its components in the bag.
3. Verify that the contents of the bag exactly matches the items as described in Package
Contents.
4. Contact Avonic for the Return Procedure.
11

MOUNTING AND INSTALLATION
This chapter describes the steps you have to perform to mount and install the Product in a correct and safe
manner.
These steps are subdivided into the following groups, each of which is described in a separate section:
1. Mounting on a wall
2. Mounting on a mounting pole
If you want to use the mount and camera in combination with the CamDirector, you need to make sure
that the MT200 is NOT compatible in combination with such a system! Use the MT220 to do this.
Take the following precautions to prevent the Product and camera from falling down which may cause
injuries:
• Mount this Product to a wall or mounting pole.
• ONLY use an Avonic mount for mounting to a wall or mounting pole.
• Ensure the mounting construction is capable of supporting four times the weight of the Product. (See
'General Specifications > Weight product’ in the Product Datasheet for the exact weight.)
• Use a safety loop or drop protection that prevents the Product from falling if the mounting construction
fails.
• During mounting and installation, NEVER install a Product above a person.
• Check the installation at least once a year. An improper mounting could cause the unit to fall off,
resulting in personal injury.
Mounting on a Wall
1. Baseplate
To install the mount, follow these instructions:
Mount the MT200 or MT220 baseplate (the bracket) to the wall (Figure 5 and 6). Make sure that you need more
screws (8) to mount the MT220 to the wall. For both mounts it is possible to connect the cables from behind the
wall. See the drawings under "Measurements and Specs" and figure 6 below.
For safety reasons, follow exactly the warning under Mounting and Installation, and make sure that the
mounting construction is capable of supporting four times the weight of the Product.
Figure 1: Baseplate
MT200 MT220
12

Figure 2: Screws and plugs
The screws and plugs are not included. See Package contents what is included.
2. Mounting the Camera
2. Place the CM40 or CM70 camera on its baseplate and mount it to its baseplate using the supplied
1/4” UNC (20mm) screws and the black M3*6mm Pozidrive screws. Make sure that you need more of
these screws if you have the MT220. See the pictures below.
3. Connect all cables to the camera (figure 8), or connect all cables from behind the wall (figure 9).
See also 1. Baseplate on page 12. The mount is designed in such a way, that you can release
both the mount and the camera, so you have your hands free for connecting the cables.
Make sure that the camera is locked to its baseplate, before you release the camera. Otherwise the
camera could move and fall off the mount!
Figure 4: Connecting cables
Figure 3: Mounting camera to the
baseplate
Figure 5: Connecting cables from behind the wall
13

3. Cable Cover
4. Put the cable cover over the back of the bracket, neatly concealing the cables and connectors
of the camera. Note that the MT220 have a bigger cover than you can see on the pictures below.
The cover cap can be screwed in place using the supplied M6 Allen bolts (Figure 9) for the MT200 as
well as the MT220.
Figure 6: Cover Cap
4. Cover Cap
5. Place the Cover cap to the 30 mm baseplate gap or gaps that are empty.
Figure 7: Cover Cap
14

Mounting on a mounting pole
Trussmount clamp and mounting pole
Trussmount clamp
If you use the MT220 in combination with a Trussmount Clamp, make sure that you use the hole in the
CENTER of the baseplate. Otherwise the mount could tilt to one side.
Follow the instructions below to use a Trussmount Clamp:
1. Follow ONLY step 2 in 2. Mounting the Camera on page 13 to mount the camera to the
baseplate.
2. Use a compatible screw, the 30MM Steel Ring to connect the clamp to the 30 mm gap in the
center of the baseplate. See the pictures below.
3. Clamp the Trussmount Clamp to the mounting pole or mounting construction.
4. Connect all cables to the camera following step 3 in 2. Mounting the Camera on page 13.
5. Place the cable cover following 3. Cable Cover on page 14 and 4. Cover Cap on page 14.
Figure 8: Mounting clamp and ring Figure 9: Result
Mounting pole
Use a third party mounting adapter to connect the MT200 or the MT220 to the mounting pole.
If you use a mounting adapter in combination with the MT220, make sure that you use the hole in the
CENTER of the baseplate. Otherwise the mount could tilt to one side.
Follow the instructions below to mount the MT200 or MT220 to a mounting pole:
1. Connect the third party mounting adapter to the baseplate of the MT200 or MT220.
2. Place the mounting adapter with the baseplate on the mounting pole.
3. Follow the steps in 2. Mounting the Camera on page 13 to mount the camera to the baseplate.
4. Place the cable cover following 3. Cable Cover on page 14 and 4. Cover Cap on page 14.
Figure 10: Mounting adapter Figure 11: Result
15

MEASUREMENTS AND SPECS MT200
16

General Specifications
Color White, Black
Dimensions product MM
(W x H x D)
2370 x 60 x 130 mm (indicative)
Weight product 1060 Kg (indicative)
Included MT200 Wall Mount, 1x Black 30MM
Cover Cap, 1x 30MM Steel Ring,
1x 1/4”- UNC Pozidrive screw to
fasten camera, M6*10mm 2x Allen
Bolt screw, M3*6mm DIN9785 5x
Pozidrive security screw
17

MEASUREMENTS AND SPECS MT220
18

General Specifications
Color White, Black
Dimensions product MM (W x H x D) 2370 x 57 x 2628 mm
Weight product 2.1 KG
Dimensions package MM (W x H x D) 2480 x 65 x 3400 mm
Weight package 2.4 KG
Included MT220 Double Wall Mount, 3x Black
30MM Cover Cap, 1x 30MM Steel Ring,
2x 1/4”- UNC Pozidrive screw to fasten
camera, M6*10mm 2x Allen Bolt screw,
M3*6mm 8x Pozidrive security screw
19

TRANSPORT AND STORAGE
The mount must be transported in its original packaging box. Inside the box, it is recommended to wrap the
mount in the original plastic bag and to place it in the protective foam.
Specific guidelines apply to the environmental temperature and humidity when operating and storing the mount
and the camera.
See 'Operating humidity' and 'Storage temperature' in the provided (camera) Datasheet for the
applicable values.
20