3 Digital Noise Reduction( 3DNR)
● T his function reduces the background noise in a low luminance environment
1. When the SET UP menu screen is displayed, select 3DNR by using the Up and
Down buttons so that the arrow indicates 3DNR.
2. Select a desired mode using the Left and Right buttons.
▶
: Deactivates 3DNR. Noise is not reduced.
WHITE BALANCE (White Bal.)
▶
: Activates 3DN so that noise is reduced.
1. When SETUP menu screen is displayed, select 'White Bal.' by using Up and 3. Set the 3DNR mode to 'ON' andpress the SET button. Then you can adjust the
Down buttons so that the arrow indicates White Bal. Noise reduction level.
※ Select one of the following 6 modes, as appropriate for your purpose
▶
: Select this when the color temperature is between 2,000ºK and 18,000ºK.
▶
AWC- > SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the SET button. If the environment changes, readjust it.
▶
: Select this to fine-tune White Balance manually. Set White Balance first by using
the ATW or AWC mode. After that switch to MANUAL mode.
Adjust the [BLUE] and [RED], according to the changing of color on the screen
1. When the SETUP menu screen is displayed, select 'SPECIAL' by using Up and
▶
: Select this when the color temperature is around 3,100ºK.
Down buttons so that the arrow indicates 'SPECIAL'
▶
: Select this when the color temperature is around 5,100ºK.
2. Select a desired mode using the Up and Down buttons
▶
: Select this when the color temperature is between 2,500ºK and 9,800ºK. ▶
: If you enter a title, the title will be appear on the monitor.
① If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow
indicates 'CAM TITLE'
② Set it to 'On' by using Left and Right buttons.
DAY/NIGHT
● You can display pictures in Color or Black and White.
③ Press the SET button.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT' by using the Up
④ Use the 4 direction buttons to move to a desired letter and select the letter by pressing the
and Down buttons so that the arrow indicates 'DAY/NIGHT'
SET button. Repeat this to enter multiple letters. You can enter up 15 letters.
▶
: The picture is always displayed in color.
▶
: The mode is switched to color in a normal environment, but switches to B/W mode
when ambient illumination is low. To set up the switching time or speed
for auto mode, press the SET button
- Delay : You can select the duration time about changing the day/night mode. ⑤ Enter a title, move the cursor to 'POS' and press the SET button. The entered title appears
- S / E - Level : You can select brightness of illumination about changing the day/night mode. on the screen. Select the position to display the title on the screen by using the 4 directoin
-> The brightness of illumination is changeable by installed environment. buttons and press the SET button. When the position is determined, select 'END' and press
▶
: Deactivates the EXT function. the SET button to return to the SPECIAL menu.
▶
: The picture is always displayed in B/W. ▶
① When the SPECIAL menu screen is displayed, press the Up and down buttons so that the
arrow indicates "D-EFFECT".
② Press the SET button for Sub menu.
* Freeze : You can stop the image or reactivate it.
* Mirror ▶
: Hide an area you want to hide on the screen.
- Mirror : you can flip the image vertically on the screen. ① When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the
- Rotate : you can flip the imate horizontally on the screen. arrow indecates 'PRIVACY'.
- V-Flip : you can flip the image vertically and horizontally both. ② Press SET button for Sub Menu.
* Digital Zoom : You can use a digital zoom of x1.0 ~ X32 ③ Set up the mode by using 4 direction buttons.
* Gamma : Standard value is 0.45. You can adjust the value between 0.05 ~ 1.00 * AREA SELECT : You can select up to 8 privacy areas.
* NEG IMAGE : you can flip the color on screen. * AREA DISPLAY : Determines whether to use the area selected in the AREA SELECT.
▶
: Deactivates the RS485 function. * LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
▶
: If you connect an alarm device to this camera, you can monitor activity * WIDTH : adjust the selected vertical area.
because a signal is generated by the camera whenever motion is detected. The * TOP / BOTTOM : Determines the coordinate of the horizontal axis for area.
motion detection signal is output through the MD OUT port. * HEIGHT : adjust the selected horizontal area.
① When the SPECIAL menu is displayed, press the * COLOR : Determine area color. You can select 0 ~ 15.
Up and Down buttons so that arrow indicates
MOTION. ▶
: You can select the menu language according to your requirement.
② Press SET button for sub menu. - It can be changes 5sec. later.
③ Set up the mode using 4 direction buttons. - Supplied Language : English, Chinese, Japanese
* AREA SELECT : Determines which 4 vertices of
each MD area is to be used
* AREA DIPLAY : Determines whetehr to use the MD area selected in Sensitivity.
1. When the SETUP menu screen is displayed, select ADJUST by using Up and
* LEFT / RIGHT : Determines the coordinate of the vertical axis for Area.
Down buttons so that arrow indicates ADJUST.
* WIDTH : Adjust the selected vertical area. ▶
Sharpness : As you increase this value, the picture outline becomes stronger and clearer
* TOP / BOTTOM : Determines the coordinate of the horizontal axis for area. Adjust this value appropriately depending on the sharpness of the picture.
* HEIGHT : Adjust the selected horizontal area. ▶
: You can adjust the color on the monitor in BLUE mode by controlling between
* Sensitivity : You can select up to 4 areas. When sensitivity number is high, 0 and 100
motion detection sensitivity is increased to recognize even small movement ▶
: You can adjust the color on the monitor in RED mode by controlling between
* Motion View : If you make it ON by using LEFT and RIGHT buttons, selected 0 and 100
value of color is filled on the screen
RESET
1. When the SETUP menu screen is displayed, select RESET by using Up and
Down buttons so that arrow indicates RESET.
2. Select a mode by using Up and Down buttons.
▶
: Resets the camera settings to the factory defaults.
Language and Communication status is not initialized
Press the SET button in the Exit menu to save the current settings and exit the Main SETUP
menu.
copyright www.avware.de
You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is 'OFF'
At this time, the exchange between DAY mode and NIGHT mode operates as COLOR mode
White balance may not work properly under the following conditions.
In this case, select the AWC mode.
①When color temperature of environment surrounding the subject is out of the control range
②If the camera towards a fluorescent, the White Balance operation may become unstable
You cannot set the 3DNR to 'ON' or 'OFF' when the AGC mode of the EXPOSURE menu is
'OFF'.
⊙When adjusting the noise reduction level of the 3DNR mdoe, the higher the level set ,
the more the noise level will be reduced but that after image may also occur.
When the CAM TITLE menu is 'OFF', no title will be displayed on the monitor screen even if
you
If you entered wrong letter……
If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a
leeter,
change the cursor to the bottom left arrow and press the SET button. Move the curson over the
MD areas show only MOTION menu. Therefore, MD areas don't display on the monitor screen.
BUT if you select the motion view function ON, MD areas are displayed on the monitor
