AVX BTA-1000 User manual

BTA-1000
BLUETOOTH STEREO AMPLIFIER BTA-1000
BLUETOOTH STEREO AMPLIFIER

1. Install this unit in a well ventilated, cool, dry, clean place – away from direct sunlight,
heat sources, vibration, dust, moisture and/or cold. For proper ventilation, do not place
anything on top of this unit or cover it in any way. This will prevent proper heat dissipa-
tion and could cause damage to this unit.
2. Avoid installing this unit where it will be exposed to any liquids dripping or splashing
or other foreign object that could damage this unit.
3. To prevent damage by lightning or power surge, keep the power cable disconnected
from any wall outlet during a lightning storm, intermittent or total power outage.
4. Do not attempt to modify or fix this unit. Contact authorized AVX Audio service
personnel when any service is needed.
WARNING:
Attempting to modify or fix this unit will void manufacturer’s warranty.
5. Be certain to read the troubleshooting section of this manual or contact an authorized
AVX Audio representative before determining this unit to be faulty.
6. Only voltage specified on this unit must be used. Using this unit with a higher voltage
than specified is dangerous and may cause fire, damage to this unit and/or personal
injury. AVX Audio will not be held liable for use of this of this unit with a voltage other
than specified herein.
7. Do not clean this unit with chemical solvents or liquids. Use only a clean, dry cloth.
8. Do not plug this unit into an AC wall outlet until all connections are completed.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

BTA-1000
BLUETOOTH STEREO AMPLIFIER BTA-1000
BLUETOOTH STEREO AMPLIFIER
Inputs and Controls – Front and Rear Panel
1. Power ON/OFF
2. Speaker A/B Selector
3. Headphone Output
4. Bluetooth Receiver
5. SD Card Input
6. USB Input
7. Input Selector
8. Play/Pause (From USB, SD or Bluetooth Only)
9. Tone Control - Use to adjust treble or bass levels
10. Repeat – Will allow current song to be repeated
11. Previous – Use to select previous song or FM radio station
12. Next – Use to select next song or FM radio station
13. IR receiver for remote control
14. Master Volume
15. DVD Input
16. Auxiliary Input
17. CD Input
18. Audio Output
19. Right Speaker Output Channel A
20. Left Speaker Output Channel A
21. Right Speaker Output Channel B
22. Left Speaker Output Channel B
23. Power Cord
12345 6 78910 11
12 13 14
15 16 17 18 19 20 21 22 23

Remote Control
Press to select TREBLE,BASS, and press " VOL+, VOL- to increase/decrease
bass or treble
TONE
for USB/SD music source.
3
For
Press to repeat song in USB/SD Playback Mode
Using the number buttons press the number(s) of the desired track.
The selected track will then be played.

(AUX)(DVD) (CD)
SPEAKER(RIGHT) SPEAKER(LEFT)
1. Plug this unit into 110V wall outlet located nearby.
2. Before powering this unit on, please refer to the chart above and confirm all speaker connec-
tions are correct / in phase. Make sure L (left) speaker is connected to left speaker and R (right)
is connected to right speaker and insure “+” to “+” and “–” to “–” are properly connected. If
speakers are not connected properly sound quality will be poor and lacking in bass.
3. Turn input selector to corresponding source that is connected to amplifier and power on
desired source.
4. If utilizing Bluetooth feature please select Bluetooth input on amplifier and then activate
Bluetooth function on your enabled device. Search for and connect to “AVX-AMP” to pair
Bluetooth enabled device wirelessly with the amplifier.
5. To use A/B function please select A or B speaker channel corresponding to speaker outputs
connected to your speakers. In the event A and B speaker outputs are to be used together
please turn selector to A+B channel position.
NOTE: DO NOT CONNECT TWO SETS OF 4 OHM SPEAKERS TO THIS UNIT, THIS MAY
CAUSE DAMAGE TO THIS UNIT.
MODEL NO:
BLUETOOTH STEREO AMPLIFIER
BTA-1000
4

Additional Information / Troubleshooting
*Please refer to the chart below if your amplifier is not functioning properly. In the event
you are experiencing an issue not outlined below, please contact an authorized AVX Audio
dealer to obtain further support.
PROBLEM CAUSE REMEDY
THE UNIT
FAILS TO
TURN ON
Protection Circuitry has
been activated because of
a short circuit.
The power cable is not
connected or the plug
is not completely inserted.
Connect the power cable firmly
Check and confirm speaker
wires are not touching and then
turn power back on.
NO SOUND
SOUND
SUDDENLY
GOES OFF
Incorrect output or input
cable connections
Verify cables are connected
properly, if problem persists
cables may be defective
Speaker A/B selector is
not set properly.
Confirm Speaker A/B selector
is set to the appropriate output
that speakers are connected to
Speaker output has been
muted. Disable the mute function.
The connected component
is not playing.
Verify component is connected
to the corresponding input
that is being selected.
The unit has become too hot
and has gone into protection
mode.
Make sure the openings on the
top panel are not covered.
Allow unit to cool.
Amplifier has turned off
Verify speaker connections are
not touching one another. This
will cause a short circuit.
THERE IS A
LACK OF
BASS
Speakers are connected out
of phase / + and - is reversed
Connect the speaker wires to
the correct + and - phase.
REMOTE
CONTROL
DOES NOT
FUNCTION
PROPERLY
The batteries are weak or
not inserted Replace all batteries.
5

FM band: 87.5~107.5MHZ,
17” x 13” x 3.5”
12lbs
13.2lbs
120V ~ 50-60 Hz
6