Awron F12DGA User manual

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 1
Installation Guide
AWRON Display F12/13DGA

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 2
Table of Contents
Table of Contents 2
Scope of delivery 3
Toolkit 4
Cabel system 5
Schematic 6
Installation Guide
•Dismantling interior trim 7
•Dismantling fresh air grille 10
•Dismantling footwell trim driver side 12
•Removing OBD connector 13
•Exposing the connector on ZGM gateway control device 14
•Exposing the connector on the CAS control unit 18
•Display installation 21
Support & FAQ 22

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 3
Scope of delivery
F12/13DGA Display modul
Cabel harness

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 4
Toolkit
Assembly tool
2mm
Socket wrench 10mm
Screwdriver TORX T25
Flat screwdriver 2mm
Mounting wedge

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 5
Cabel system
150cm
USB

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 6
Schematic

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 7
Disassembly interior trim
Remove with a plastic wedge the interior trim. Start from the right. Pay attention to the connectors.
Remove black connector
Remove interior trim

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 8
Disassembly interior trim
Remove cable from fixing point
See picture

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 9
Disassembly interior trim
Remove white connector
Remove the interior trim and prepare for dismantling

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 10
Dismantling air grill
Use T15 Torx screwdriver
Unscrew all screws, see arrows

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 11
Dismantling interior trim
Air grill take out
Install F1xDGA display module

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 12
Disassembly panel under the glove box on driver side
Unleash screws. Wrench size 10mm
Fold down the the cover

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 13
Remove the OBD connector
Unlock the blue locking clip in direction of arrow
Pull out the OBD connector as well as the footwell lighting, see arrows

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 14
Uncovering of the connector on ZGM gateway controller
Unlock and disconnect the blue connector
ZGM gateway control unit in the footwell top left

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 15
Uncovering of the connector on ZGM gateway controller
Remove the black plug
Unlock the Black plug

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 16
Pinene out cable Pin 41 (yellow), Pin 46 (blue / red) and pin 47 (red)
Pull off black cover cap
CAN_L
CAN_H
4647 41

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 17
Picture showing right connection on booth connector (white and blue).

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 18
Remove the black plug
Uncovering of the connector on CAS control unit
CAS in the footwell on the top right

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 19
Auspinen cable to pin 14 (green / white) and pin 12 brown / black)
Pull the cap
Uncovering of the connector on CAS control unit
12 14

Installation instr. F13DGA
Autor:
AWRON GmbH
Version: V1.0
Datum: 15.05.2014
Seite: 20
Cable to pin 12 (brown / black) and pin 14 green / white) from AWRON harness coming into the plug
again pinene back. The out pints cable into the black connector pinen and insert it into the black
mating connector.