Axelent SAFE-X M033-041-100RL User manual

AXELENT SAFE-X AB · BOX 1 · KÄVSJÖVÄGEN 17 ·335 04 HILLERSTORP, SWEDEN
TEL: [phone] · [e-mail] · WWW.AXELENTSAFEX.SE
Pedestrian Barrier Telescopic Gate Assembly instructions
Components
Tools required
Telescopic Gate
PB-K-TGATE
Telescopic Gate Accessories
PB-K-TGA
Telescopic Gate Fixings
PB-K-GATE-FXG
Rubber mallet 2.5mm
allen key
4mm
allen key
5.5mm
allen key
6mm
allen key
Circlip/long
nose pliers
*Some components included within “M” bundles.
M033-041-100RL (650-1000mm)

AXELENT SAFE-X AB · BOX 1 · KÄVSJÖVÄGEN 17 ·335 04 HILLERSTORP, SWEDEN
TEL: [phone] · [e-mail] · WWW.AXELENTSAFEX.SE
Pedestrian Barrier Telescopic Gate Assembly instructions
Orientation
Right Hand Left Hand
Direction of
escape
Direction of
escape
Always open
into walkway
Always open
into walkway
Catch post:
PB end post
Hinge Post:
PB Corner post
Catch post:
PB end post
Hinge Post:
PB Mid post
Min 860mm
Max 1210mm
Min 650mm
Max 1000mm
Min 860mm
Max 1210mm
Min 650mm
Max 1000mm

AXELENT SAFE-X AB · BOX 1 · KÄVSJÖVÄGEN 17 ·335 04 HILLERSTORP, SWEDEN
TEL: [phone] · [e-mail] · WWW.AXELENTSAFEX.SE
1 2
34
5 6
7 8
Pedestrian Barrier Telescopic Gate Assembly instructions
Gate Installation:
Install hinge and catch post as per Pedestrian
Barrier instructions.
Catch post:
End post
Hinge post:
PB mid post
Min 860mm
Max 1210mm
Connect the gate hinge to the hinge post.
Fasten the gate to the post at each connecting point
using the gate fixing kit.
Using allen keys secure each of the 3 fixing points.
Adjust telescopic arm to suit opening. Secure telescopic arm by securing set screws on the
underside of both the top and bottom tubes.
If desired, apply the PUSH and PULL labels as appropriate. Gate installation complete.

AXELENT SAFE-X AB · BOX 1 · KÄVSJÖVÄGEN 17 ·335 04 HILLERSTORP, SWEDEN
TEL: [phone] · [e-mail] · WWW.AXELENTSAFEX.SE
1 2
34
5 6
7 8
Pedestrian Barrier Telescopic Gate Assembly instructions
Fasten the gate to the post at each connecting point
using the gate fixing kit.
Remove the gate arm assembly from the hinge plate
assembly.
Using a 4mm allen key remove the cam retaining cap head
screws.
Rotate bottom cam from RH to LH orientation.
Using 4mm allen key secure cam into the LH orientation
using the removed cap head screws.
Replace the gate arm assembly back on the hinge plate
assembly.
RH/LH Gate swap:
Telescopic Gate as standard is supplied in the RH orientation
(reference page 2 fo 5)
Using long nose pliers/circlip pliers remove pin retaining
circlip.

AXELENT SAFE-X AB · BOX 1 · KÄVSJÖVÄGEN 17 ·335 04 HILLERSTORP, SWEDEN
TEL: [phone] · [e-mail] · WWW.AXELENTSAFEX.SE
9
10
11 12
13 14
15 16
Pedestrian Barrier Telescopic Gate Assembly instructions
Ensure all 4 set screws in the gate arm are loosened off. remove the telescopic arm from the gate assembly.
Spin/flip around the remaining gate assembly to other
direction. Spin/flip over the telescopic arm to match the other direction.
Remove the hinge pin from th gate assembly.
Using long nose pliers/circlip pliers remove pin retaining circlip.
Reinstall the telescopic arm into the gate assembly in the
new orientation.
Conversion to LH orientation complete.
GB1908_1.0_JOJE