Aydin Displays CAMBRIDGE CFP47W1 User manual

CAMBRIDGE
USERS MANUAL
CFP47W1 Large Screen Series
VESA Wall Mount
LCD Monitor User Guide
Document No. 150-CFP-470

150-CFP-470
Page 2
Contents
Important Safety Instructions ………………………………………………... 3
 Safety Precautions …………………………………………………………………...…… 3
 Installation ………………....………………………………………………………….…… 3
 Technical Help ……………………………….…………………………………………… 3
 Cleaning Your Display ……………….…………………………………….……………… 3
Features………………………………………………………………….……........ 4
Package Contents ……….....…………………….……………………………... 4
 Dimension ……………………………………………………………………………….… 6
 Installation ……………………………………………………………………………….… 7
 Power Input …………….…….………………………………………………………….… 7
 Power Interface ………..…….………………………………………………………….… 7
 Connection …………….…..……….……………………..…………………………….… 8
 Single Source Input ………….……………………………………………….................. 8
Operating The Monitor …….…………….……………………………............... 9
 The Side Controller Of The Monitor ……….....……………………..….…………….… 9
 The Remote Controller (RCU) Instructions ……………..…………………………….… 9
 Change The RCU Battery ………………..….………………………….……………..… 10
 Display Mode ……..…………………..………… ……………….……………..… 11
 OSD Menu Function ……..…………………..………………………….……………..… 12
 OSD Operating ……………..……………..….………………………….……………..… 13
Default Setting …………………………………………………………….……... 16
Supported Timing ………..…………………………….………………….……... 17
Specification …………..……………….………................................................ 18
Troubleshooting …………………………………….……….…………………... 19
Compliance ……………………………..…………………….…………………... 19
Appendix ………………………………..…………………….…………………... 20
Appendix II …..…………………………..…………………….………………….. 21

※Please read this user’s manual completely before operating this monitor.
Safety Precautions
To turn off the power of the monitor, press”O” on the main power switch at back cover.
The power standby/on indicator goes off and the set cannot to be turned on/ off by using the POWER
button on the remote control. (To turn on/off the monitor by the remote control, press the main power
switch again and light the power standby/on indicator.)
 When turning off the monitor by pressing the POWER button on the remote control, the main power of
the monitor is not turned off completely.
 To disconnect the monitor completely from power supply, remove the power plug from the outlet.
Press”O”to turn off monitor completely
If the power cord or plug is damaged or becomes hot, turn off the main power switch of
the monitor, make sure the power plug has cooled down and remove the power plug
from the outlet.
Installation (when install the monitor, please follow the instruction on the manual )
Don't install in temperatures exceeding specifications.
If the monitor used in environments with temperatures exceeding specifications, it may cause the case or
other parts be distorted, damaged, overheating or an electric shock.
Don't install in a high-humidity environment exceeding specifications.
This may cause overheating or an electric shock.
TechnicalHelp
When having technical problems, please contact Aydin Displays customer service.
CleaningYourDisplay
Cleaning the surface of the monitor.
 When the surface of the monitor is polluted, please wipe the surface with the cotton or clean cloth
lightly.
 If pollution is not easy to clean out, can use the cloth with 50% of the alcohol .
 Please notice carefully that not to let alcohol enter the monitor, it may cause electrical failures.
150-CFP-470
Page 3

Features
High-resolution HD panel
This monitor supports 1920 x 1080 HDTV format and can display true 16.7M colors, you can enjoy extreme fine
pictures.
MVA system less-reflection black TFT LCD panel
MVAsystem and Black TFT LCD panel offer bright and wide images with clear contrast. Even placed near the
windows, the monitor shows bright and clear image with little reflection. The viewing angles of the monitor are as
wide as 170° both horizontally and vertically, enough to enjoy clear images at any view angle.
Offer varieties of connection
Video system Input:
There are 3 choices of connection RGB Input: There are 2 choices of connection Signal delivery
VIDEO RCA
S-VIDEO Mini Din 4 pin
COMPONENT Mini Din 8 pin
RGB ANALOG D-Sub 15pin
RGB DIGITAL DVI-ID 24pin
RS-232C in D-sub 9pin (Option)
Other functions
 Building the light sensor inside, the monitor will adjust the brightness according to the surrounding light
intensity.
 There are two brightness levels pre-set. Under the bright condition, it will adjust to the bright mode.
Under the dim condition, the monitor will adjust to dim mode automatically.
 Signal source auto detection.
 PIP/ PAP function. Please see the chapter “Display mode ”
 Zoom in/out function.
Package Contents
Unpacking
CFP47W1 is packed by the carton box. During transportation, in order to protect the monitor, CFP47W1 is
packed by cushions to be safe protect and package.
Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet for your monitor
first.
Set the LCD Monitor box in an upright position and open from the top of the box before removing the top
cushions.
 Step 1: Remove the white handle and cut the bundle
150-CFP-470
Page 4

 Step 2: Remove the top cushion and take the accessories box out.
Top cushion &
Accessories Box
Bottom cushion
The Monitor
Packing list
Q’ty Item Q’ty Item
1 set CFP47W1 1 pcs DVI-D 24 pin cable
1 pcs Power cord 1 pcs D-SUB 15pin cable
1 pcs User's manual 1 pcs S-VIDEO Mini Din 4 pin cable
1 pcs Remote controller 1 pcs Component Mini Din 8 pin cable
1 pcs RCA cable 1 pcs RS232C D-sub 9pin cable (Option)
150-CFP-470
Page 5

Dimension (Front & Back)
150-CFP-470
Page 6

Installation
Environmental state
Operating temperature︰5℃ ~ 40℃ (Fahrenheit : 41℉ ~ 104℉)
Humidity︰max. 85%
Power Input
Power Cord
AC Power cord
This power cord is used to connect the side controls of the LCD monitor and the wall outlet.
Connect the power cord into main power of the monitor, “│” is power on, “○”is power off.
Input: 100-240V~ 3A 50/60Hz
150-CFP-470
Page 7
Sin
g
le In
p
ut Interface
The side of control
○is
p
ower off
│is power on
Main power –Switch &
AC socket
Power Interface
 Main interface- switch & AC socket. Please see the chapter “Power input ”
 The side controller of the monitor
 The remote control (RCU)

Connection
 Video (RCA ) input
 S-Video input
 Component Y Pb/Pr input
 DVI (DVI-D) input
 RGB (VGA) input
 RS-232C input (option)
Single Source Input
Input Interface
NO. Name Remarks
1 Video-IN input connecter RCA
2 S-video input connecter Mini Din 4 pin
3 Y-Pb-Pr (Y-Cb-Cr) inputs Mini Din 8 pin
4 DVI input connecter DVI-D 24 pin
5 RGB input connecter D-Sub 15 pin
6 Power cord input
7 RS232C-IN input (option) D-Sub 9 pin
The Video Signals Input
You can select Video input form 3 connections below:
Video signals Connection type Signal
Video RCA NTSC/PAL
S-Video 4 pins NTSC/PAL
(Y Pb/Cb Pr/Cr) 8 pins NTSC/PAL
150-CFP-470
Page 8
 Suitable signal is automatically selected.

RGB inputting
You can select RGB input for 2 connections as below:
RGB signals Connection type Signal
RGB Analog VGA 15 pins RGB Analog
RGB Digital DVI-D DVI-D 24 pins RGB Digital
Command delivery Connection type Function
RS-232C (Option) 9 pin communication port
Operating The Monitor
TheSideControllerOfTheMonitor
No. Key Description
1 Power Power Switch ; Power ON/OFF
2 ENTER Activate selection
3 〈 / + Menu right / Value increasing
4 〉/ - Menu left / Value decreasing
5 ＾Menu down
6 ﹀Menu up
7 MENU Enter OSD menu / Exit menu or select
The Remote Control (RCU) Instructions
No. Key Description
1 POWER Power ON / OFF
2 YMenu left
3 △Menu up
4 ENTER Enter
5 AUTO
A
djust clock, phase, H & V position
automatically
6 PIP Picture in picture
7 MENU OSD menu
8 ZMenu right
9 ▽Menu down
10 EXIT Exit and one level up
11 SOURCE Input source selection
12 SWITCH PIP picture switch
1
2
3
4
7
8
9
10
5
6
11
12
150-CFP-470
Page 9
λ OSDLock/UnlockControl
Use control push buttons at side
Lock: Press (Z/+) and (▽) at the same time and OSD will be locked.
Unlock: Press (Z/+) and (▽) at the same time again and OSD will be unlocked.

Use remote controller
Lock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence and OSD will be locked.
Unlock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence again and OSD will be unlocked.
Change The RCU Battery (RCU option)
(1) (2)
(3)
i. Push down as picture (1) and pull the back cover.
ii. Replace with the new batteries as picture (2), 1 piece Lithium battery(CR2032) make sure
the polarity of batteries are correct.
iii. Place back cover and slide it is as picture (3).
iv. Used batteries need to follow the city rule to discard.
v. Avoid keeping used, old batteries inside the remote control, causing leakage of internal liquid
resulting metal rust or fatal damage to the remote control hand unit.
vi. Battery used according to the instruction
.
CAUTION
 Risk of explosion if batty is replaced by an incorrect type.
 Dispose of used batteries according to the instructions.
150-CFP-470
Page 10

DisplayMode
Main Source mode
The main source mode will be changed in the sequence as follows: VGA/DVI/ Composite (AV) / S-Video/
Component (YPbPr) by remote control or press “MENU”->”T” by the side controller of the monitor.
PIP(sub source) mode
Press “PIP” button on the remote control (turn on PIP function), and press” source” to select PIP input source.
There is no PIP button on side controller of the monitor.
The sub-source changes as the main source changes. (Picture 1)
Sub source
Main source
<Picture 1>
“●” is activity option, “-----“ is inactivity option.
Example:
When main source is Composite (AV signal), the sub-source can select to VGA or DVI.
When main source is VGA, the sub-source can select to composite, S-Video or component.
150-CFP-470
Page 11

OSD (On Screen Display) Menu Function
Main Menu Sub-Menu
(base on IGP mode) Description Setting
Brightness Adjust the brightness of the screen 0~100
Contrast Adjust the contrast of the screen 0~100
Hue Adjust the picture hue of the screen -45~+45
Saturation Adjust the picture saturation of the screen 0,100
Flash-Tone Adjust the picture tone of screen Off/Weak/Soft/Strong
DISPLAY
Black Level Adjust the black level of screen
(IGP mode enable only) 0,100
Zoom Magnify the picture of screen In/Out
Zoom Horizontal Pan Select the left/right picture to magnify Left/Right
Zoom Vertical Pan Select the upper/down picture to magnify Down/Up
Vertical Adjust the V-position of the Zoom picture 0~255
POSITION
Horizontal Adjust the H-position of the Zoom picture 0~255
PIP Mode Adjust the PIP mode Off/Singe/PAP
PIP Size Adjust the PIP size Small/Med\/Large
Vertical Adjust the V-position of PIP 0~100
PIP
CONTROL Horizontal Adjust the H-position of PIP 0~100
Scaling Select the picture ratio. 1:1/Fill/Aspect/panor
Auto Adjust Auto adjustment Select
Phase Adjust the screen phase
(IGP mode enable only) 0~255
Clock Adjust the screen clock
(IGP mode enable only) 0~255
MEPG NR No working. Future option
(IGP mode disable)
Noise Reduction Select the noise reduction mode
(IGP mode disable) Off/Low/Med/High
Angle Filtering Select the angle filtering function
(IGP mode disable) Off/ On
Film mode Defect Select the film mode defect function
(IGP mode disable) Off/ On
IMAGE
Sharpness Adjust the sharpness of the screen
(IGP mode disable) -15~ 29
Gamma correction Select the Gamma setting Off/ 2.2/ 2.4
Color Temperature Select the color temperature setting User/3200K/6500K,
7500K/9300K
Red Adjust red color 0~255
Green Adjust green color 0~255
Main /
Second
Input
signal
setting
COLOR
Blue Adjust blue color 0~255
Volume Adjust the volume of the OSD menu 0~100
150-CFP-470
Page 12
Balance Adjust the balance of the OSD menu -15~+15
Bass Adjust the bass of the OSD menu -7 ~+7
Audio setting
(option)
Treble Adjust the treble of the OSD menu -7 ~+7

Vertical Adjust the OSD menu V-position 0~255
Horizontal Adjust the OSD menu H-position 0~255
Blend Adjust the OSD menu of blend 0~15
Time out Adjust the OSD menu display time 0~60
OSD menu
OSD Zoom Magnify the OSD menu On/Off
Language Language Language setting English
Factory reset Reset to the factory default setting Yes/ No
Set display address Select monitor ID address(optional) 0~255
Light Sensor Select the light sensor setting On/ Off
Default
setting Light sensor Value Adjust the light sensor value 0~100
VGA
DVI
Composite
S-Video
RCU
Input signal selection
Component
 (IVP) means selection is working on Video mode.
 (IGP) means selection is working on VGA mode.
OSDOperating
Structure of OSD Menus
λ Main Menu
 On side of controller:
Press “MENU” to enter Main Menu
Press“
＜/¬” or “＞/﹣” to select Main Menu ex (Picture setting,
Language, Original Default Setting)
 On RCU:
Press “MENU” to enter Main Menu
Press“Z” or “Y” to select Main Menu ex (Picture setting,
Language, Original Default Setting).
150-CFP-470
Page 13

λ Display Setting-
 On side of controller:
1.Press “MENU” ->” ENTER” to enter “DISPLAY” item.
2.Press ”﹀” to select sub-item(Brightness, contrast, Hue….),
3.Press“＜/¬” or “＞/﹣” to adjust
4.Press “ENTER” to save the setting, when finished adjusting.
5.Press “MENU” to exit the item.
 On RCU:
1.Press the “MENU” ->” ENTER” to enter “DISPLAY” item.
2.Press ”▽” to enter sub-item(Brightness, contrast, Hue….),
3.Press “Z” or “Y” to adjust
4.Press ”ENTER” to save the setting, when finish adjusting.
5.Press “EXIT” to exit the item.
λ Picture Setting
 On side of controller:
1.Press “MENU” to enter Main Menu.
2.Press “＞/﹣“ 2 times to select picture setting.
3.Press “Enter” to enter item.
4.Press ”﹀” to select sub-item(Vertical, Horizontal, Blend...),
5.Press “＜/¬” or “＞/﹣” to adjust
6.Press ”Enter” to save the setting, when finish adjusting.
7.Press the “MENU” to exit the item.
 On RCU:
1.Press the “MENU” ->” ENTER” to enter picture setting
2.Press“Z” or “Y” to select Main Menu.
3.Press the “ENTER “ to enter item.
4.Press ”▽” to enter sub-item(Vertical, Horizontal, Blend…),
5.Press “Z” or “Y” to adjust
6.Press “ENTER” to save the setting, when finish adjusting.
7.Press” EXIT“ to exit the item
150-CFP-470
Page 14

λ Language Setting (English only)
 On side of controller:
1.Press “MENU” to enter Main Menu.
2.Press “＞/﹣” 3 times and press the “Enter” to enter item.
3.Press ”﹀” to select sub-item(English only),
4.Press ”Enter” to save the setting, when finish adjusting.
5.Press “MENU” to exit the item.
 On RCU:
1.Press “MENU” ->” ENTER” to enter picture setting
2.Press“Z” or “Y” to select Main Menu.
3.Press “ENTER “ to enter item.
4.Press ”▽” to enter sub-item(English only),
5.Press “ENTER” when finish adjusting.
6.Press” EXIT“ to exit the item
λ OriginalDefaultSetting
 On side of controller:
1.Press “MENU” to enter Main Menu.
2.Press “＞/﹣” 4 times to select original default setting.
3.Press “Enter” to enter item.
4.Press ”﹀” to select sub-item(Factory Reset. Set display …),
5.Press “＜/¬” or “＞/﹣”to adjust
6.Press ”Enter” to save the setting ,when finish adjusting.
7.Press “MENU” to exit the item.
 On RCU:
1.Press “MENU” to enter Main Menu.
2.Press“Z” or “Y” to select Main Menu.
3.Press “ENTER “ to enter item.
4.Press ”▽” to enter sub-item(Factory Reset. Set display …),
5.Press “Z” or “Y” to adjust
6.Press “ENTER” to save the setting, when finish adjusting..
7.Press” EXIT“ to exit the item
λ Input Signal Selection
 On side of controller:
1.Press the “MENU” to enter Main Menu.
2.Press “﹀” to enter
3.Press “＜/¬” or “＞/﹣” to select single input.
4.Press ”Enter” when finish adjusting.
 On RCU:
1.Press the “MENU” to enter Main Menu.
2.Press ”▽” to enter
3.Press “Z” or “Y” to select single input.
4.Press “Enter” when finish adjusting.
150-CFP-470
Page 15

150-CFP-470
Page 16
Default Setting
Item Default
Power switch Off
Brightness 80
Contrast 50
Color temp. User
Red 255
Green 255
Blue 255
Language English
Auto Adjust On

Supported Timing
Sync
polarity Horizontal (dot) Vertical (line)
Item
Video Mode fH
(kHz) fV (Hz)
Dot
clock
(MHz) H V A B C D E O P Q R S
Analog
Digital
Componen t
1 31.469 59.940 25.175 N N 800 96 48 640 16 526 2 33 480 11 O O
2 37.861 72.809 31.500 N N 832 40 128 640 24 520 3 28 480 9 O O
3
VGA 640x480
37.500 75.000 31.500 N N 840 64 120 640 16 500 3 16 480 1 O O
4 35.156 56.250 36.000 P P 1024 72 128 800 24 625 2 22 600 1 O O
5 37.879 60.317 40.000 P P 1056 128 88 800 40 628 4 23 600 1 O O
6 48.077 72.188 50.000 P P 1040 120 64 800 56 666 6 23 600 37 O O
7
SVGA 800x600
46.875 75.000 49.500 P P 1056 80 160 800 16 625 3 21 600 1 O O
8 48.363 60.004 65.000 N N 1344 136 160 1024 24 806 6 29 768 3 O O
9 56.476 70.069 75.000 N N 1328 136 144 1024 24 806 6 29 768 3 O O
10
XGA 1024x768
60.023 75.029 78.750 P P 1312 96 176 1024 16 800 3 28 768 1 O O
11 1152x864 67.500 75.000 108.000 P P 1600 128 256 1152 64 900 3 32 864 1 O O
12 63.981 60.020 108.000 P P 1688 112 248 1280 48 1066 3 38 1024 1 O O
13
VESA
SXGA 1280x1024 79.976 75.025 135.000 P P 1688 144 248 1280 16 1066 3 38 1024 1 O O
14 640x480 35.000 66.667 30.240 N N 864 64 96 640 64 525 3 39 480 3 O O
15 832x624 49.725 74.500 57.283 N N 1152 64 224 832 32 667 3 39 624 1 O O
16
Macintosh
1024x768 60.150 74.720 80.000 N N 1330 96 168 1024 42 805 3 31 768 3 O O
17 WXGA 1360x768 47.72 59.95 84.75 P P 1776 152 176 1360 88 796 3 24 768 1 O O
18 37.50 50.000 74.250 N N 1980 40 220 1280 440 750 5 20 720 5 O O
19 44.96 59.94 74.18 P P 1650 40 220 1280 110 750 5 20 720 5 O O
20
720p 1280x720
45.00 60.00 74.25 P P 1650 40 220 1280 110 750 5 20 720 5 O O
21 28.13 25.00 74.25 P P 2460 44 528 1920 148 562 2 5 540 15 O O
22 33.716 59.94 74.176 P P 2200 44 88 1920 148 562 3 19 540 O O O
23
1080i 1920x1080
33.716 59.94 74.176 P P 2200 44 88 1920 148 562 3 19 540 O O O
24 62.5 50 148.5 P P 2376 66 243 1920 147 1250 1 160 1080 9
OO
25 56.25 50 148.5 P P 2640 11 148 1920 528 1125 5 36 1080 4
OO
26 67.433 59.94 148.352 P P 2200 44 148 1920 88 1125 5 36 1080 4 OO
27
1080p 1920x1080
67.5 60 148.5 P P 2200 44 148 1920 88 1125 5 36 1080 4
OO
fH
Item
Video Mode
(kHz) fV (Hz)
Dot
clock
(MHz)
Analog Composite S-Video Component
1 480i NTSC 358-443 15.743 59.94 16.521 O O O O
2 576i PAL SECAM 15.625 50.00 16.406 O O O O
3 480P 720X480 31.542 60.08 27.00 O
4 576P 720X576 31.25 50 28.812 O
150-CFP-470
Page 17

Specification
Item Specification Unit
Active Area 1042.56(H) x 586.44(V) 47” diagonal Mm
Driver Element a-si TFT active matrix -
Pixel Number 1920 x R.G.B. x 1080 pixel
Pixel Arrangement RGB Vertical Stripe -
Display Color 16.7M color
Trans-missive Mode Normally Black -
ViewingAngle (H / V) 176 / 176 degree
Brightness 500 (typ.) cd/m2
Contrast Ratio 1000(typ.) -
LCD panel
Response Time 8 (Gray to Gray, typ.) msec
Separate Sync. LVDS Level -
Horizontal Sync. Positive / Negative -
Vertical Sync. Positive / Negative -
Graphic
Input Connector D-Sub 15 pins, DVI-D 24 pins, Component
Composite, S-Video, RS-232C(option) -
Auto Adjust Clock, Phase, H Position & V Position -
Screen Scaling VGA/SVGA/XGA/SXGA/WXGA Full Screen Display -
Power Management VESA DPMS, DVI DMPM -
Gamma Correction Off, 2.2, 2.4
Color Adjustment User, 3200K, 5400K, 6500K & 9300K -
OSD Language English -
PIP 4 size; small/ Middle/ Large/PAP
Performance
Zoom Zoom in / out
Power supply Input AC (Worldwide) V
Operation Mode
≤
290 (max.) W
Power consumption Power Saving Mode
≤
20(max) W
Dimension, (WxHxD) 1139.4x126.4x684.39 (w/o stand) mm
Net Weight 43.7 kg
Physical
Gross Weight 50.7 kg
Function OSD key 7 key
Wall mount VESA standard 200x 200 ;200x 600 mm
150-CFP-470
Page 18

150-CFP-470
Page 19
Troubleshooting
Before calling Aydin Displays customer service, please check the following chart for a possible cause to the
trouble you are experiencing.
 Perform the adjustments according to page 10 “Operation The Monitor”
 Refer to the following items if you can’t find a proper item listed in the Operating the Monitor or if the problem
remains.
 if the problem you have experienced isn’t described below or you can’t correct the problem, stop using the
monitor and call service personnel or your dealer.
Problem Check these things
No Display Check the power plug insert on wall outlet..
Check the main power switch
If AC socked is OK, please check another set of equipment.
Check input single, the signal may not be suitable.
Display is not in the center. If the signal timing of the computer is within the spec.
Display is shaking. If the signal timing of the computer is within the spec.
The remote control doesn’t work Make sure the battery is inserted matching the + and – marks of the
battery compartment.
The battery may be exhausted..
Use the remote control aiming at the remote control sensor.
The picture color is pale, or not clear Check picture quality to adjust.
If you are using YUV terminals, make sure cables are correctly connected.
Compliance
FCC Compliance Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CE
EN 55022、EN 61000-3-2、EN-61000-3-3
EN 55024、IEC61000-4
EN 60950 [Low-Voltage Directive (73/23/EEC)]

Appendix I
 Moving Notice:
Moving the monitor requires at least two people. If not, it may drop and a serious injury may result.
Moving/shipping the monitor, please hold the white handles and be sure to make the bundle. If not, it
may drop and a serious injury may result. Please see as below pictures.
150-CFP-470
Page 20