Aztech HL129EW User manual

Reset
Button In Room A, plug in your HomePlug AV device into a
power outlet and connect it to your router’s ethernet
port using an Ethernet cable.
Make sure that your router’s internet connection is
up to allow you to access the internet.
Connect an ethernet cable from the PC to any of the
available Ethernet Ports of your HL129EW.
On your computer, turn OFF any Wireless Adapter (if
applicable).
Open and Launch a web browser. Type in 10.0.10.254
on the web browser’s url link then hit enter key.
1.
2.
3.
Confirm that the connection was established on
both HomePlug AVs. Successful connection is
indicated by Green light on both Power and Power
Line Activity LEDs. Your HomePlug AV is now ready
to use and may now access the internet.
In Room B, plug in your HL129EW device into a
power outlet. You may connect any device (e.g.
computer / notebook) to its available ethernet
ports and you may also connect any of your
wireless devices to your HL129EW’s WiFi (SSID and
Password is printed at the label sticker located at
the top surface of your device).
2.
Enter admin for Username and admin for
Password.
Click the Network menu and select the Wireless
Setting (2.4GHz / 5.0GHz) that you want to configure.
After changing the preferred settings, click Apply to
save and apply settings.
4.
5.
6.
1.
BDevice Overview
APackage Contents
Power
LED
Gigabit
Ethernet
Ports 1
& 2
WPS
Button /
LED
HL129EW
HL129EW Ethernet
Cable
Easy Start
Guide
Warranty
Policy
CSetup for New Network Connection
Ensure to follow the connection set up below.
HomePlug A HL129EW
Router Desktop / PC
Wireless Devices
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1 2
2
3
DConfiguring Wireless Settings (Optional)
Ensure to follow the connection set up below.
HL129EW
Router Desktop / PC
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1
2
3
HomePlug A
Powerline Activity
LED / Simple
Connect Button
3.
HL129EW
1200Mbps SmartLink HomePlugAV2
Dual Band Wireless-AC Extender
2.4GHz /
5.0GHz
Wireless
LEDs

Reset
Button In Room A, plug in your HomePlug AV device into a
power outlet and connect it to your router’s ethernet
port using an Ethernet cable.
Make sure that your router’s internet connection is
up to allow you to access the internet.
Connect an ethernet cable from the PC to any of the
available Ethernet Ports of your HL129EW.
On your computer, turn OFF any Wireless Adapter (if
applicable).
Open and Launch a web browser. Type in 10.0.10.254
on the web browser’s url link then hit enter key.
1.
2.
3.
Confirm that the connection was established on
both HomePlug AVs. Successful connection is
indicated by Green light on both Power and Power
Line Activity LEDs. Your HomePlug AV is now ready
to use and may now access the internet.
In Room B, plug in your HL129EW device into a
power outlet. You may connect any device (e.g.
computer / notebook) to its available ethernet
ports and you may also connect any of your
wireless devices to your HL129EW’s WiFi (SSID and
Password is printed at the label sticker located at
the top surface of your device).
2.
Enter admin for Username and admin for
Password.
Click the Network menu and select the Wireless
Setting (2.4GHz / 5.0GHz) that you want to configure.
After changing the preferred settings, click Apply to
save and apply settings.
4.
5.
6.
1.
BDevice Overview
APackage Contents
Power
LED
Gigabit
Ethernet
Ports 1
& 2
WPS
Button /
LED
HL129EW
HL129EW Ethernet
Cable
Easy Start
Guide
Warranty
Policy
CSetup for New Network Connection
Ensure to follow the connection set up below.
HomePlug A HL129EW
Router Desktop / PC
Wireless Devices
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1 2
2
3
DConfiguring Wireless Settings (Optional)
Ensure to follow the connection set up below.
HL129EW
Router Desktop / PC
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1
2
3
HomePlug A
Powerline Activity
LED / Simple
Connect Button
3.
HL129EW
1200Mbps SmartLink HomePlugAV2
Dual Band Wireless-AC Extender
2.4GHz /
5.0GHz
Wireless
LEDs

Reset
Button In Room A, plug in your HomePlug AV device into a
power outlet and connect it to your router’s ethernet
port using an Ethernet cable.
Make sure that your router’s internet connection is
up to allow you to access the internet.
Connect an ethernet cable from the PC to any of the
available Ethernet Ports of your HL129EW.
On your computer, turn OFF any Wireless Adapter (if
applicable).
Open and Launch a web browser. Type in 10.0.10.254
on the web browser’s url link then hit enter key.
1.
2.
3.
Confirm that the connection was established on
both HomePlug AVs. Successful connection is
indicated by Green light on both Power and Power
Line Activity LEDs. Your HomePlug AV is now ready
to use and may now access the internet.
In Room B, plug in your HL129EW device into a
power outlet. You may connect any device (e.g.
computer / notebook) to its available ethernet
ports and you may also connect any of your
wireless devices to your HL129EW’s WiFi (SSID and
Password is printed at the label sticker located at
the top surface of your device).
2.
Enter admin for Username and admin for
Password.
Click the Network menu and select the Wireless
Setting (2.4GHz / 5.0GHz) that you want to configure.
After changing the preferred settings, click Apply to
save and apply settings.
4.
5.
6.
1.
BDevice Overview
APackage Contents
Power
LED
Gigabit
Ethernet
Ports 1
& 2
WPS
Button /
LED
HL129EW
HL129EW Ethernet
Cable
Easy Start
Guide
Warranty
Policy
CSetup for New Network Connection
Ensure to follow the connection set up below.
HomePlug A HL129EW
Router Desktop / PC
Wireless Devices
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1 2
2
3
DConfiguring Wireless Settings (Optional)
Ensure to follow the connection set up below.
HL129EW
Router Desktop / PC
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1
2
3
HomePlug A
Powerline Activity
LED / Simple
Connect Button
3.
HL129EW
1200Mbps SmartLink HomePlugAV2
Dual Band Wireless-AC Extender
2.4GHz /
5.0GHz
Wireless
LEDs

Reset
Button In Room A, plug in your HomePlug AV device into a
power outlet and connect it to your router’s ethernet
port using an Ethernet cable.
Make sure that your router’s internet connection is
up to allow you to access the internet.
Connect an ethernet cable from the PC to any of the
available Ethernet Ports of your HL129EW.
On your computer, turn OFF any Wireless Adapter (if
applicable).
Open and Launch a web browser. Type in 10.0.10.254
on the web browser’s url link then hit enter key.
1.
2.
3.
Confirm that the connection was established on
both HomePlug AVs. Successful connection is
indicated by Green light on both Power and Power
Line Activity LEDs. Your HomePlug AV is now ready
to use and may now access the internet.
In Room B, plug in your HL129EW device into a
power outlet. You may connect any device (e.g.
computer / notebook) to its available ethernet
ports and you may also connect any of your
wireless devices to your HL129EW’s WiFi (SSID and
Password is printed at the label sticker located at
the top surface of your device).
2.
Enter admin for Username and admin for
Password.
Click the Network menu and select the Wireless
Setting (2.4GHz / 5.0GHz) that you want to configure.
After changing the preferred settings, click Apply to
save and apply settings.
4.
5.
6.
1.
BDevice Overview
APackage Contents
Power
LED
Gigabit
Ethernet
Ports 1
& 2
WPS
Button /
LED
HL129EW
HL129EW Ethernet
Cable
Easy Start
Guide
Warranty
Policy
CSetup for New Network Connection
Ensure to follow the connection set up below.
HomePlug A HL129EW
Router Desktop / PC
Wireless Devices
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1 2
2
3
DConfiguring Wireless Settings (Optional)
Ensure to follow the connection set up below.
HL129EW
Router Desktop / PC
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1
2
3
HomePlug A
Powerline Activity
LED / Simple
Connect Button
3.
HL129EW
1200Mbps SmartLink HomePlugAV2
Dual Band Wireless-AC Extender
2.4GHz /
5.0GHz
Wireless
LEDs

Reset
Button In Room A, plug in your HomePlug AV device into a
power outlet and connect it to your router’s ethernet
port using an Ethernet cable.
Make sure that your router’s internet connection is
up to allow you to access the internet.
Connect an ethernet cable from the PC to any of the
available Ethernet Ports of your HL129EW.
On your computer, turn OFF any Wireless Adapter (if
applicable).
Open and Launch a web browser. Type in 10.0.10.254
on the web browser’s url link then hit enter key.
1.
2.
3.
Confirm that the connection was established on
both HomePlug AVs. Successful connection is
indicated by Green light on both Power and Power
Line Activity LEDs. Your HomePlug AV is now ready
to use and may now access the internet.
In Room B, plug in your HL129EW device into a
power outlet. You may connect any device (e.g.
computer / notebook) to its available ethernet
ports and you may also connect any of your
wireless devices to your HL129EW’s WiFi (SSID and
Password is printed at the label sticker located at
the top surface of your device).
2.
Enter admin for Username and admin for
Password.
Click the Network menu and select the Wireless
Setting (2.4GHz / 5.0GHz) that you want to configure.
After changing the preferred settings, click Apply to
save and apply settings.
4.
5.
6.
1.
BDevice Overview
APackage Contents
Power
LED
Gigabit
Ethernet
Ports 1
& 2
WPS
Button /
LED
HL129EW
HL129EW Ethernet
Cable
Easy Start
Guide
Warranty
Policy
CSetup for New Network Connection
Ensure to follow the connection set up below.
HomePlug A HL129EW
Router Desktop / PC
Wireless Devices
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1 2
2
3
DConfiguring Wireless Settings (Optional)
Ensure to follow the connection set up below.
HL129EW
Router Desktop / PC
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1
2
3
HomePlug A
Powerline Activity
LED / Simple
Connect Button
3.
HL129EW
1200Mbps SmartLink HomePlugAV2
Dual Band Wireless-AC Extender
2.4GHz /
5.0GHz
Wireless
LEDs

Reset
Button In Room A, plug in your HomePlug AV device into a
power outlet and connect it to your router’s ethernet
port using an Ethernet cable.
Make sure that your router’s internet connection is
up to allow you to access the internet.
Connect an ethernet cable from the PC to any of the
available Ethernet Ports of your HL129EW.
On your computer, turn OFF any Wireless Adapter (if
applicable).
Open and Launch a web browser. Type in 10.0.10.254
on the web browser’s url link then hit enter key.
1.
2.
3.
Confirm that the connection was established on
both HomePlug AVs. Successful connection is
indicated by Green light on both Power and Power
Line Activity LEDs. Your HomePlug AV is now ready
to use and may now access the internet.
In Room B, plug in your HL129EW device into a
power outlet. You may connect any device (e.g.
computer / notebook) to its available ethernet
ports and you may also connect any of your
wireless devices to your HL129EW’s WiFi (SSID and
Password is printed at the label sticker located at
the top surface of your device).
2.
Enter admin for Username and admin for
Password.
Click the Network menu and select the Wireless
Setting (2.4GHz / 5.0GHz) that you want to configure.
After changing the preferred settings, click Apply to
save and apply settings.
4.
5.
6.
1.
BDevice Overview
APackage Contents
Power
LED
Gigabit
Ethernet
Ports 1
& 2
WPS
Button /
LED
HL129EW
HL129EW Ethernet
Cable
Easy Start
Guide
Warranty
Policy
CSetup for New Network Connection
Ensure to follow the connection set up below.
HomePlug A HL129EW
Router Desktop / PC
Wireless Devices
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1 2
2
3
DConfiguring Wireless Settings (Optional)
Ensure to follow the connection set up below.
HL129EW
Router Desktop / PC
WALL
ROOM A ROOM B Powerline Network
Ethernet Cable
1
2
3
HomePlug A
Powerline Activity
LED / Simple
Connect Button
3.
HL129EW
1200Mbps SmartLink HomePlugAV2
Dual Band Wireless-AC Extender
2.4GHz /
5.0GHz
Wireless
LEDs

If you want to add your HL129EW device to your
existing network, simply plug in the device to any wall
socket; by default it will pair up with your HomePlug
AV devices. Once paired, your device is now ready to
use.
1.
2.
A.
However, just in case you have changed the Private
Network Name of your existing network, you may use
the Simple Connect button of your HL129EW and the
old devices as indicated below:
Press the Simple Connect Button of your HL129EW
for 10 seconds until the Power and Power Line
Activity LED turn OFF and turn ON.
Press the Simple Connect Button of your old device
for two seconds. The Power LED will start blinking.
On your HL129EW, press the Simple Connect button
for two seconds. The Power LED will start blinking
and the Power Line Activity LED will be on steady
green, indicating a succesful pairing with the old
devices.
B.
C.
Ensure that you have the proper set up as indicated
in Section D (Configuring Wireless Settings). Follow
steps 3, 4, and 5 respectively of Section D.
Go to the Wireless > Security section, then on the WPS
section, tick Enable then click Apply.
F Enabling the WPS Function (Optional)
1.
2.
3.
4.
GDetermining Connection Rate
EachLEDcolor ofthePowerline ActivityLEDrepresents
a connection rating. The connection rating can only
be calculated when the device is part of an existing
network. The exact connection rate value can also be
viewed using the HomePlug AV Web User Interface.
HDevice Reset
To perform RESET to factory defaults, press the Reset
button for 2 to 4 SECONDS. The LEDs will turn OFF and
turn ON to indicate device reset.
E Setup for an Existing Network Connection
Press for 2 to 4 SECONDS to
perform factory default reset.
* The Easy Start Guide is designed to get you up and
running with your Aztech HL129EW HomePlug. This
Easy Start Guide including the User Manual which
provides a more advanced guide to this product, can
be from the Aztech Support Website
(www.aztech.com/support).
Powerline Activity LED
On your HL129EW, press the WPS button for 2
seconds. The Wireless LED will start to blink slowly.
Enable/Press the WPS button on the device that
you wish to connect to HL129EW. Complete the
steps 3 and 4 of this section within two minutes to
ensure a succesful connection .
Press for 2 seconds
to initiate the Wi-Fi
Protected Setup (WPS).
Press for 10 seconds.
Press for 2 seconds.
GREEN
Connection rate
is more than
120 Mbps
AMBER
Connection rate is
between 30 to
120 Mbps
RED
Connection rate
is less than
30 Mbps
Note to Red LED: It is recommended to plug the device
to main wall-socket plug or a plug with the least electrical
interference.

If you want to add your HL129EW device to your
existing network, simply plug in the device to any wall
socket; by default it will pair up with your HomePlug
AV devices. Once paired, your device is now ready to
use.
1.
2.
A.
However, just in case you have changed the Private
Network Name of your existing network, you may use
the Simple Connect button of your HL129EW and the
old devices as indicated below:
Press the Simple Connect Button of your HL129EW
for 10 seconds until the Power and Power Line
Activity LED turn OFF and turn ON.
Press the Simple Connect Button of your old device
for two seconds. The Power LED will start blinking.
On your HL129EW, press the Simple Connect button
for two seconds. The Power LED will start blinking
and the Power Line Activity LED will be on steady
green, indicating a succesful pairing with the old
devices.
B.
C.
Ensure that you have the proper set up as indicated
in Section D (Configuring Wireless Settings). Follow
steps 3, 4, and 5 respectively of Section D.
Go to the Wireless > Security section, then on the WPS
section, tick Enable then click Apply.
F Enabling the WPS Function (Optional)
1.
2.
3.
4.
GDetermining Connection Rate
EachLEDcolor ofthePowerline ActivityLEDrepresents
a connection rating. The connection rating can only
be calculated when the device is part of an existing
network. The exact connection rate value can also be
viewed using the HomePlug AV Web User Interface.
HDevice Reset
To perform RESET to factory defaults, press the Reset
button for 2 to 4 SECONDS. The LEDs will turn OFF and
turn ON to indicate device reset.
E Setup for an Existing Network Connection
Press for 2 to 4 SECONDS to
perform factory default reset.
* The Easy Start Guide is designed to get you up and
running with your Aztech HL129EW HomePlug. This
Easy Start Guide including the User Manual which
provides a more advanced guide to this product, can
be from the Aztech Support Website
(www.aztech.com/support).
Powerline Activity LED
On your HL129EW, press the WPS button for 2
seconds. The Wireless LED will start to blink slowly.
Enable/Press the WPS button on the device that
you wish to connect to HL129EW. Complete the
steps 3 and 4 of this section within two minutes to
ensure a succesful connection .
Press for 2 seconds
to initiate the Wi-Fi
Protected Setup (WPS).
Press for 10 seconds.
Press for 2 seconds.
GREEN
Connection rate
is more than
120 Mbps
AMBER
Connection rate is
between 30 to
120 Mbps
RED
Connection rate
is less than
30 Mbps
Note to Red LED: It is recommended to plug the device
to main wall-socket plug or a plug with the least electrical
interference.

If you want to add your HL129EW device to your
existing network, simply plug in the device to any wall
socket; by default it will pair up with your HomePlug
AV devices. Once paired, your device is now ready to
use.
1.
2.
A.
However, just in case you have changed the Private
Network Name of your existing network, you may use
the Simple Connect button of your HL129EW and the
old devices as indicated below:
Press the Simple Connect Button of your HL129EW
for 10 seconds until the Power and Power Line
Activity LED turn OFF and turn ON.
Press the Simple Connect Button of your old device
for two seconds. The Power LED will start blinking.
On your HL129EW, press the Simple Connect button
for two seconds. The Power LED will start blinking
and the Power Line Activity LED will be on steady
green, indicating a succesful pairing with the old
devices.
B.
C.
Ensure that you have the proper set up as indicated
in Section D (Configuring Wireless Settings). Follow
steps 3, 4, and 5 respectively of Section D.
Go to the Wireless > Security section, then on the WPS
section, tick Enable then click Apply.
F Enabling the WPS Function (Optional)
1.
2.
3.
4.
GDetermining Connection Rate
EachLED color ofthePowerlineActivity LEDrepresents
a connection rating. The connection rating can only
be calculated when the device is part of an existing
network. The exact connection rate value can also be
viewed using the HomePlug AV Web User Interface.
HDevice Reset
To perform RESET to factory defaults, press the Reset
button for 2 to 4 SECONDS. The LEDs will turn OFF and
turn ON to indicate device reset.
E Setup for an Existing Network Connection
Press for 2 to 4 SECONDS to
perform factory default reset.
* The Easy Start Guide is designed to get you up and
running with your Aztech HL129EW HomePlug. This
Easy Start Guide including the User Manual which
provides a more advanced guide to this product, can
be from the Aztech Support Website
(www.aztech.com/support).
Powerline Activity LED
On your HL129EW, press the WPS button for 2
seconds. The Wireless LED will start to blink slowly.
Enable/Press the WPS button on the device that
you wish to connect to HL129EW. Complete the
steps 3 and 4 of this section within two minutes to
ensure a succesful connection .
Press for 2 seconds
to initiate the Wi-Fi
Protected Setup (WPS).
Press for 10 seconds.
Press for 2 seconds.
GREEN
Connection rate
is more than
120 Mbps
AMBER
Connection rate is
between 30 to
120 Mbps
RED
Connection rate
is less than
30 Mbps
Note to Red LED: It is recommended to plug the device
to main wall-socket plug or a plug with the least electrical
interference.

If you want to add your HL129EW device to your
existing network, simply plug in the device to any wall
socket; by default it will pair up with your HomePlug
AV devices. Once paired, your device is now ready to
use.
1.
2.
A.
However, just in case you have changed the Private
Network Name of your existing network, you may use
the Simple Connect button of your HL129EW and the
old devices as indicated below:
Press the Simple Connect Button of your HL129EW
for 10 seconds until the Power and Power Line
Activity LED turn OFF and turn ON.
Press the Simple Connect Button of your old device
for two seconds. The Power LED will start blinking.
On your HL129EW, press the Simple Connect button
for two seconds. The Power LED will start blinking
and the Power Line Activity LED will be on steady
green, indicating a succesful pairing with the old
devices.
B.
C.
Ensure that you have the proper set up as indicated
in Section D (Configuring Wireless Settings). Follow
steps 3, 4, and 5 respectively of Section D.
Go to the Wireless > Security section, then on the WPS
section, tick Enable then click Apply.
F Enabling the WPS Function (Optional)
1.
2.
3.
4.
GDetermining Connection Rate
EachLEDcolor ofthe Powerline Activity LED represents
a connection rating. The connection rating can only
be calculated when the device is part of an existing
network. The exact connection rate value can also be
viewed using the HomePlug AV Web User Interface.
HDevice Reset
To perform RESET to factory defaults, press the Reset
button for 2 to 4 SECONDS. The LEDs will turn OFF and
turn ON to indicate device reset.
E Setup for an Existing Network Connection
Press for 2 to 4 SECONDS to
perform factory default reset.
* The Easy Start Guide is designed to get you up and
running with your Aztech HL129EW HomePlug. This
Easy Start Guide including the User Manual which
provides a more advanced guide to this product, can
be from the Aztech Support Website
(www.aztech.com/support).
Powerline Activity LED
On your HL129EW, press the WPS button for 2
seconds. The Wireless LED will start to blink slowly.
Enable/Press the WPS button on the device that
you wish to connect to HL129EW. Complete the
steps 3 and 4 of this section within two minutes to
ensure a succesful connection .
Press for 2 seconds
to initiate the Wi-Fi
Protected Setup (WPS).
Press for 10 seconds.
Press for 2 seconds.
GREEN
Connection rate
is more than
120 Mbps
AMBER
Connection rate is
between 30 to
120 Mbps
RED
Connection rate
is less than
30 Mbps
Note to Red LED: It is recommended to plug the device
to main wall-socket plug or a plug with the least electrical
interference.

If you want to add your HL129EW device to your
existing network, simply plug in the device to any wall
socket; by default it will pair up with your HomePlug
AV devices. Once paired, your device is now ready to
use.
1.
2.
A.
However, just in case you have changed the Private
Network Name of your existing network, you may use
the Simple Connect button of your HL129EW and the
old devices as indicated below:
Press the Simple Connect Button of your HL129EW
for 10 seconds until the Power and Power Line
Activity LED turn OFF and turn ON.
Press the Simple Connect Button of your old device
for two seconds. The Power LED will start blinking.
On your HL129EW, press the Simple Connect button
for two seconds. The Power LED will start blinking
and the Power Line Activity LED will be on steady
green, indicating a succesful pairing with the old
devices.
B.
C.
Ensure that you have the proper set up as indicated
in Section D (Configuring Wireless Settings). Follow
steps 3, 4, and 5 respectively of Section D.
Go to the Wireless > Security section, then on the WPS
section, tick Enable then click Apply.
F Enabling the WPS Function (Optional)
1.
2.
3.
4.
GDetermining Connection Rate
EachLEDcolor ofthe Powerline Activity LED represents
a connection rating. The connection rating can only
be calculated when the device is part of an existing
network. The exact connection rate value can also be
viewed using the HomePlug AV Web User Interface.
HDevice Reset
To perform RESET to factory defaults, press the Reset
button for 2 to 4 SECONDS. The LEDs will turn OFF and
turn ON to indicate device reset.
E Setup for an Existing Network Connection
Press for 2 to 4 SECONDS to
perform factory default reset.
* The Easy Start Guide is designed to get you up and
running with your Aztech HL129EW HomePlug. This
Easy Start Guide including the User Manual which
provides a more advanced guide to this product, can
be from the Aztech Support Website
(www.aztech.com/support).
Powerline Activity LED
On your HL129EW, press the WPS button for 2
seconds. The Wireless LED will start to blink slowly.
Enable/Press the WPS button on the device that
you wish to connect to HL129EW. Complete the
steps 3 and 4 of this section within two minutes to
ensure a succesful connection .
Press for 2 seconds
to initiate the Wi-Fi
Protected Setup (WPS).
Press for 10 seconds.
Press for 2 seconds.
GREEN
Connection rate
is more than
120 Mbps
AMBER
Connection rate is
between 30 to
120 Mbps
RED
Connection rate
is less than
30 Mbps
Note to Red LED: It is recommended to plug the device
to main wall-socket plug or a plug with the least electrical
interference.

If you want to add your HL129EW device to your
existing network, simply plug in the device to any wall
socket; by default it will pair up with your HomePlug
AV devices. Once paired, your device is now ready to
use.
1.
2.
A.
However, just in case you have changed the Private
Network Name of your existing network, you may use
the Simple Connect button of your HL129EW and the
old devices as indicated below:
Press the Simple Connect Button of your HL129EW
for 10 seconds until the Power and Power Line
Activity LED turn OFF and turn ON.
Press the Simple Connect Button of your old device
for two seconds. The Power LED will start blinking.
On your HL129EW, press the Simple Connect button
for two seconds. The Power LED will start blinking
and the Power Line Activity LED will be on steady
green, indicating a succesful pairing with the old
devices.
B.
C.
Ensure that you have the proper set up as indicated
in Section D (Configuring Wireless Settings). Follow
steps 3, 4, and 5 respectively of Section D.
Go to the Wireless > Security section, then on the WPS
section, tick Enable then click Apply.
F Enabling the WPS Function (Optional)
1.
2.
3.
4.
GDetermining Connection Rate
EachLEDcolor ofthe Powerline Activity LED represents
a connection rating. The connection rating can only
be calculated when the device is part of an existing
network. The exact connection rate value can also be
viewed using the HomePlug AV Web User Interface.
HDevice Reset
To perform RESET to factory defaults, press the Reset
button for 2 to 4 SECONDS. The LEDs will turn OFF and
turn ON to indicate device reset.
E Setup for an Existing Network Connection
Press for 2 to 4 SECONDS to
perform factory default reset.
* The Easy Start Guide is designed to get you up and
running with your Aztech HL129EW HomePlug. This
Easy Start Guide including the User Manual which
provides a more advanced guide to this product, can
be from the Aztech Support Website
(www.aztech.com/support).
Powerline Activity LED
On your HL129EW, press the WPS button for 2
seconds. The Wireless LED will start to blink slowly.
Enable/Press the WPS button on the device that
you wish to connect to HL129EW. Complete the
steps 3 and 4 of this section within two minutes to
ensure a succesful connection .
Press for 2 seconds
to initiate the Wi-Fi
Protected Setup (WPS).
Press for 10 seconds.
Press for 2 seconds.
GREEN
Connection rate
is more than
120 Mbps
AMBER
Connection rate is
between 30 to
120 Mbps
RED
Connection rate
is less than
30 Mbps
Note to Red LED: It is recommended to plug the device
to main wall-socket plug or a plug with the least electrical
interference.