Baby Lock BLRG20ST Reference guide

NEEDLE AND THREAD INFORMATION
Use the correct needle system (134). Choose from sizes 12 through 21,
according to the type of thread used. A guide to help you choose the
correct combinaon of needle and threads is always available on the Regalia
Staonary machine. From the Home screen, tap the System Informaon
buon and choose the Needle and Thread Guide buon.
QUICK REFERENCE CARD
TO THREAD THE REGALIA
www.BabyLock.com Part #QM30026 • ©
1. Place thread cone onto spool post (1), thread through thread-mast eyelet (2) from back to
front and pass through thread guide (3).
2. Connue to three-hole thread guide (4). Wrap all three holes from back to front, being
careful not to cross threads. If delicate threads are breaking, skip one or two holes to
lessen tension.
3. Pass through thread guide (5) and connue
down to tension assembly (6). Ensure
that the thread is ossed between the
two tension discs.
4. Catch the take-up spring (7) with thread and
pull it down under the srrup thread guide (8).
5. Bring the thread up and through the hole of
the take-up lever (9) from back to front, and
then through the lower thread guide (10).
Finally, thread through the needle bar thread
guide hole (11).
6. Follow the groove down the front of the needle
and insert thread through the eye of the needle (12)
from front to back. While pulling thread through
the eye, be careful that the thread does not twist
around the needle.

REGALIA SCREEN BUTTONS
MAIN SCREEN BUTTONS
Start: Press the Start button to begin quilting.
Stop: Press the button to stop quilting.
Needle-stop: Touch to toggle between having
the needle stop in the up or down position when
you stop stitching. It does not aect the needle
at the time you touch the button. Your choice
displays in green.
Easy-Set Tension®:The number on the button
indicates the current tension, which is set by
manually turning the tension knob.
Reset-bobbin: If you are using the low-bobbin
alarm, press this button after a bobbin change
to reset the reading to indicate that you have
inserted a full bobbin. The number that appears
on the button shows an estimate of how much
thread remains on the bobbin. The closer to zero,
the less thread remains on the bobbin.
On-screen hand wheel: Rotate the back hand
wheel and cycle the needle and hopping foot
from the screen by dragging your nger down
the icon in the direction of the arrows.
NOTE: Number does not indicate yards.
See To add new bobbin conguration
and record bobbin capacity in the Toolbar
Options section of the online user manual.
�CAUTION: Do not drag in the opposite
direction.
Manual Stitching Mode: Touch the Manual
button and then specify the stitches per minute
(SPM) by pressing the (+) or (-) button or
selecting one of the three SPM presets.
The faster you move the fabric, the longer
the stitches become.
Regulated Stitching Mode: Touch the
Regulated button and then select either Cruise
or Precision stitch regulation. A consistent stitch
length (stitches per inch) will be maintained
regardless of how fast the fabric is moved, unless
moved too fast for the machine to keep up.
Cruise Stitch Regulation: Touch the Cruise
button and specify the stitches per inch (SPI)
and stitches per minute (SPM) cruise settings.
Machine starts to stitch immediately, at the
chosen SPM cruise speed, when the Start/Stop
button is pressed. When you begin to move
the machine, a consistent stitch length will be
maintained (SPI). Press Start/Stop again to stop
stitching.
Precision Stitch Regulation: In this mode,
the machine stitches only when the machine is
moved. Touch the Precision button and specify
the stitches per inch (SPI). Press the Start/Stop
button and move the fabric to start quilting.
When you stop moving the fabric, the needle will
pause in mid-stroke. Move the fabric to resume
stitching.
MACHINE TOOLS
These buttons are available after
selecting the Machine Tools button.
Timer,
counter,
and alarm
Calculator Software
updater
Tension
assembly
reset
Diagnostics
MACHINE SETTINGS
These buttons are available after selecting the
Machine Settings button.
Low-
bobbin
alarms
Pinpoint
needle
laser
on/o
Alarms
on/o
Languages
STITCHING MODES Gold = selected
TOOLBAR
BUTTONS Home
Touch to return to
home screen.
Machine
Settings
Start/Stop Indicator
Play icon indicates Start
Pause icon indicates Stop
System Information
(includes threading guide
and needle/thread guide)
�CAUTION: While in Precision mode,
stitching can happen accidentally if the
fabric is bumped or moved. To prevent
inadvertent stitches, press the Start/Stop
button when not actively quilting. The
needle will return to the currently selected
Up/Down position.
Lights Machine
Tools