BaBylissMEN 7755GU User manual

Model 7755GU
THE STEEL EDITION
MAINS HAIR CLIPPER SET

SAFETY CAUTIONS
• This appliance should only be used as described within this
instruction book. Please retain for reference.
IMPORTANT CHILD SAFETY
WARNING! Polythene bags over the product or packaging
may be dangerous. To avoid danger of suffocation, keep away
from babies and children. These bags are not toys.
IMPORTANT SAFETY
• Do not immerse the appliance in water or other liquids.
• Always inspect the appliance before use for noticeable signs
of damage. Do not use if damaged or if the appliance has
been dropped. In the event of damage contact the Conair
Customer Care Line (refer to UK After Sales Service section
for further information).
• Only use the attachments supplied with this appliance.
• Do not leave the appliance unattended when switched on.
• Do not place the appliance on any surface whilst in operation.
• Special care is required when using the appliance close to
the ears, eyes and face.
• This appliance should not be used by adults whose reduced
physical, sensory or mental capabilities, or whose lack of
experience and knowledge, might cause a hazard, unless
they have been correctly instructed to understand the safe
use and hazards involved and are adequately supervised.
• Careful adult supervision is required when this appliance is
used on or near children. Do not use on very young children.
• This appliance should not be used, cleaned or maintained by
children. Keep out of reach of children.
• Always ensure that this appliance is kept out of the reach

of children at all times, particularly during use and whilst
cooling.
• Allow the appliance to cool before storing away.
• This product contains batteries (2 x AAA batteries) that are
not to be removed from the appliance for charging.
• The supply terminals are not to be short circuited.
• For indoor, household, domestic use only.
• This product complies fully with all appropriate EU and UK
Legislation and the standards relevant to this type and class
of appliance. We are an ISO9001:2015 credited company
that continually evaluates our Quality Management System
performance. If you have any queries regarding product
safety and compliance, please contact the Conair Customer
Care Line (refer to «UK After Sales Service» section).
• The battery should be removed for safe disposal at the end
of its life.

THE STEEL EDITION
MAINS HAIR CLIPPER SET
FEATURES
• Mains operated clipper for continuous high power during use
• Super sharp stainless steel blades
• Includes a separate battery operated trimmer for neckline and sideburns
• 6 clipper comb guides; grades 1, 2, 3, 4, 6, 8
• Cleaning brush
• Oil
• Wash bag
INSTRUCTIONS FOR USE
Mains Operated Clipper
Oiling Instructions
IMPORTANT! It is highly recommended before each use to oil the blades
with the oil provided. This ensures optimum cutting performance. For the
rst use you will need to use the oil supplied with the product. Unscrew
the cap and cut off the very end of the plastic tube with a pair of scissors
to release the oil. To oil the blades, ensure the appliance is switched on.
Gently squeeze the oil tube and apply 2 drops of oil onto the blades. Leave
the unit on for a further few seconds to allow the oil to thoroughly spread
the length of the blades. Switch off the unit and remove any excess oil by
gently dabbing with a cloth.

Comb Guides
This appliance is supplied with 6 comb guides:
• To attach a comb guide, ensure the appliance is switched off. Slide the
cutting blades of the clipper under the slot in the rear of the teeth of the
cutter guide and snap the clip on the bottom of the guide, over the
bottom edge of the xed clipper blade.
• To remove a comb guide, ensure the appliance is switched off. Push the
tab on the rear of the comb guide away from the head and lift off.
Preparation for Use
• Always inspect the appliance for noticeable signs of damage. Do not use
if damaged.
• Always inspect the appliance before use to ensure the clipper blades are
free from hair, debris etc.
• Ensure the appliance is well oiled.
• Always inspect the appliance before use to ensure the clipper blades are
free from hair, debris etc.
• For best performance, use on clean, dry hair that has been combed until
tangle-free.
• Prior to use always inspect the head for warts, moles, spots and broken
skin. Special care should be taken to avoid injury and cuts.
• Remove any head jewellery such as earrings and necklaces before use.
Please Note: This appliance should not be used for longer than 20 minutes
of continuous use.
Cutting Length Grade
0.5mm #0
3mm #1
6mm #2
9.5mm #3
13mm #4
19mm #6
25mm #8

Clipping
For an all over even cut:
• Attach a comb guide as required – your clipper is supplied with 6 comb
guides (Grades 1, 2, 3, 4, 6, 8). Each comb guide is labelled.
• Switch the clipper on and the blades will start to move.
• Starting at the nape of the neck, hold the clipper with the teeth of the
clipper pointing upwards, ensuring that the comb guide is resting at
against the head.
• Slowly move the clipper upwards and outwards through the hair towards
your crown, against the direction of growth. The comb guide will help to
lift the hair and the blades will cut the hair at the desired length.
• Once the desired length is achieved at the back of the hair, start clipping
the top and sides.
• Hold the clipper to the front of your hair with the teeth pointing towards
the back of your head and move the clipper towards your crown. Repeat
as necessary, moving in rows from the front and sides of your head to the
back.
• You should achieve an even length cut all over your head.
For a shorter back and sides, with length on the top:
• Attach the longer comb guide as required for the top of your hair – your
clipper is supplied with 6 comb guides (Grades 1, 2, 3, 4, 6, 8). Each
comb guide is labelled.
• Switch the clipper on and the blades will start to move.
• Hold the clipper to the front of your hair with the teeth pointing towards
the back of your head and move the clipper towards your crown. Repeat
as necessary, moving in rows from the front and the sides of your head
to the back.
• If you wish to take the back and sides of your hair to a shorter length,
switch off the appliance and attach a shorter comb guide.
• Starting at the nape of the neck, with the comb guide at against the
head, move the clipper upwards and outwards over the area you want to
take shorter.
• Repeat on the sides of the hair, starting with the teeth of the clipper
pointing upwards and comb guide at against the area above the ear,
again moving the clipper upwards and outwards.

Outlining:
• To tidy the edged around your cut, e.g. the neckline and sideburns,
detach the comb guides.
• Hold the appliance upside down, so the front of the clipper is facing
towards your head.
• Hold the clipper straight on your sideburns or neckline and move the
clipper downwards. This will give you a clean, smooth nish.
CLEANING & MAINTENANCE
To maintain optimum performance, the appliance should be cleaned after
each use.
• Switch the appliance off and unplug at the mains supply.
• Remove any comb guides. Rinse the comb guide under the running
water and dry thoroughly before storage or use.
Removable Blades
To make cleaning easier, the BaBylissMEN clipper blades can be removed.
• Make sure that the trimmer is off and remove the cutting guide.
• Hold the clippers with the blades pointing up and remove them by
pressing the points (Fig.1).
CLEANING & MAINTENANCE
To maintain optimum performance, the appliance should be cleaned after
each use.
• Switch the appliance off and unplug at the mains supply.
• Remove any comb guides. Rinse the comb guide under the running
water and dry thoroughly before storage or use.
Removable Blades
To make cleaning easier, the BaBylissMEN clipper blades can be removed.
• Make sure that the trimmer is off and remove the cutting guide.
• Hold the clippers with the blades pointing up and remove them by
pressing the points (Fig. 1).
• Carefully brush the blades using the cleaning brush to remove the hair.
• Rinse the blades under water without immersing the product.
After cleaning, switch the appliance on, and oil the blades by adding a few
drops of the oil supplied over the blades. Only use the lubricating oil sup-
plied with this appliance as this is specically formulated for high speed
clippers and does not evaporate or slow the blades
Please note: Do not attempt to repair or replace the blades. In the event
that the blades become blunt or damaged, contact the Conair Customer
Care Line.
(Fig. 1)
19_7755U_IB.indd 7 5/23/2019 3:11 PM
• Carefully brush the blades using the cleaning brush to remove the hair.
• Rinse the blades under water without immersing the product.
After cleaning, switch the appliance on, and oil the blades by adding a few
drops of the oil supplied over the blades. Only use the lubricating oil sup-
plied with this appliance as this is specically formulated for high speed
clippers and does not evaporate or slow the blades.

Please note: Do not attempt to repair or replace the blades. In the event
that the blades become blunt or damaged, contact the Conair Customer
Care Line.
Precision Trimmer
The precision trimmer can be used for tidying sideburns and neckline. It
can also be used to maintain a beard or moustache.
Preparation for Use
• Prior to initial use, test the trimmer on a small area of arm or leg hair. If
any signs of allergic reaction or sensitivity occur, discontinue use. Do not
use on very sensitive or irritated skin.
• Always inspect the appliance before use for noticeable signs of damage.
Do not use if damaged.
• Ensure the trimmer head is free from hair and other debris.
Changing the Battery
The trimmer requires 2 x AAA batteries (1.5V). To insert or replace the
battery, hold the trimmer upside down with the back of the unit facing you.
Placing one thumb on the Triangular Mark of battery cover, rmly push up
to remove the battery cover. Insert the battery as indicated on the inside of
the battery compartment. Replace the battery cover by sliding it back into
the main trimmer until it clicks into place. If the appliance remains unused
for a while or if the battery runs down, remove it from the appliance. Do
not mix old and new batteries.Do not mix alkaline,standard(carbon-zinc),or
rechargeable(Nickel cadmium or Nickel Metal Hybride) batteries.
Changing the Trimmer Heads
• Your trimmer is supplied with one removable cutting head.
• Make sure the trimmer is switched off.
• To remove the trimming head. Hold the trimming with the blades pointing
up and remove them by pressong their points. (g.2)
• To reassemble the head onto th body, with the trimmer facing away from
you, place the bottom of the blade on to the trimmer and push the blade
down until it clicks into place. (g3)

Trimming
Neckline:
• Switch the appliance on.
• Hold the trimmer with the teeth of the trimmer pointing upwards, yet at
against the skin.
• Move the trimmer upward and outward through the hair, against the
direction of hair growth.
• The trimmer will work most efciently when cutting though the hair at its
own speed. Never force the trimmer.
• Never switch the appliance off whilst in the hair.
Sideburns:
• Use a comb to comb the hair in the direction of the growth.
• Always trim your sideburns from the top down.
Beards
Outlining:
• After having combed through your beard in the direction of growth,
outline the desired shape, starting under your jawline.
• Work backwards on each side of your face towards your ears.
• Dene the upper outline of your beard across your cheeks, past your
sideburns and towards your hairline.
Outlining Moustache:
• Use the comb to comb hairs in the direction of growth.
• Use the blades only to dene the outline of the bottom of your moustache.
g.2 g.3

BATTERY DISPOSAL
To minimise hazards to health and the environment at the end of
this product’s life, laws dealing with Waste Electrical and Electronic
Equipment (WEEE) and The Waste Battery Directive require you to
dispose of these products and their batteries at a suitable collection
facility where they will be sent for appropriate recycling. Please contact
your local authorities for more details on recycling and safe disposal of
these in your area.
UK GUARANTEE
The Conair Group Ltd, Unit 3, Waterfront Business Park,
Fleet GU51 3TW
This BaBylissMEN appliance is guaranteed for consumer use for 3 years
and is only valid within the United Kingdom.
This guarantee covers consumer use only i.e. defects occurring under
normal use within the home from date of purchase or date of delivery,
whichever is later.
If the product develops a fault due to defects in materials or manufacture
within 12 months from the date of purchase, to avoid delays and
unnecessary inconvenience, where possible please return the product to
the point of purchase for an exchange,
If the product develops a fault due to defects in materials or manufacture
after 12 months from the date of purchase, and within the guarantee
period, Conair UK After Sales Service will repair or replace the product.
Exclusions
This guarantee will no longer be valid meaning that The Conair Group Ltd
will not be liable to repair or replace your product where:
1.) The appliance has been used on a voltage supply other than that which
is marked on the product, or advised within this instruction booklet
2.) The appliance has been purchased from an unauthorised stockist*
3.) The appliance is used for professional / non domestic usage
4.) Repairs or alterations have been attempted by unauthorised persons