Backyard Discovery Dakota Ridge Use and care manual

Made in China | INS-1905023B-DAKOTA RIDGE-ENG 10/25/21
For the most up to date assembly manual,
to register your set, or to order replacement parts please visit
www.backyarddiscovery.com
SAVE THIS ASSEMBLY MANUAL FOR FUTURE REFERENCE IN THE EVENT THAT
YOU NEED TO ORDER REPLACEMENT PARTS.
Model # 1905023B
Dakota Ridge
Wooden Swing Set
Owner's Manual & Assembly Instructions
MANUFACTURED BY:
Backyard Discovery
3305 Airport Drive
Pittsburg, KS 66762
800-856-4445
average 2 person assembly time
assembly time may vary based on skill level

itotio ,
GOCONFIGURE
Putting it all together for you
INSTALLATION
SERVICES
AVAILABLE!*
Need a helping hand?
Let our team of professionals handle the installation for you!
GOCON
FIGU
RE
888-888-5424
*Installation services are only available
to U.S. customers.
With Go Configure, we bring you 18 years of experience right to your doorstep.
We service a wide array of indoor and outdoor recreation products that most consumers
don't have the time or ability to deliver & install themselves.
We do the heavy lifting, so you don't have to!
• 18+ Years of Experience
Servicing Big Box Retailers and Direct Consumers • Satisfaction Guarantee
• Highly Skilled, Specialized, Courteous, Professional Service Technicians
• Flexible
Appointments, including weekends
• Over 140,000 Installations Annually • Coverage across the nation
• White Glove
Service
Visit www.goconfigure.com for more
info!
*Installation services are only available to U.S. customers.
2
2

• • •
.....
• •
• Owner's Manual Please Read This Before Starting Assembly •••••
• • •
•• •
III III
STO1 3
MISSING A PART?
CALL US BEFORE GOING
0 BACK TO THE STORE 111
The store where you made your purchase
does not stock parts for
this item.
If you have assembly questions or you are
missing or
have damaged parts, please call
1 -8 00 .8 5 6 .444 5
you can also visit www.backyarddiscovery.com
or e-mail [email protected]
Please have the following information ready when you make your call:
• Model Number of the product located on the front of the assembly manual
• Description of the
part from the parts list
• Read entire assembly manual, paying special attention to the important tips and safety information.
• Ensure there are no missing pieces by fi rst separating and identifying all parts.
• Make sure to check packing material for small parts that may have
fallen out during shipment.
• Structures are not intended for public use. Any unintended use such as home child care, daycare center,
faith center, government facility, home owner's associate, park or school will make the warranty of our
product nul l & void.
• This manual contains helpful information concerning assembly preparation, installation procedure and
required maintenance.
• Always keep safety in mind as your structure is being built.
• Keep these instructions for future reference.
3
3

• • •
•• •• ••
• • •
Owner ' s Manual Limited Warranty
• • •
• • •
• •••
THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY
CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE
This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but
not limited to Adventure Playsets, and Leisure Time Products.
Backyard Discovery Wood Play Structure
Backyard Discovery warrants this wooden play product to be free from defects in materials
and workmanship for a period of two (2) years from the
original date of purchase. All wood carries a five (5) year warranty against rot and decay from the original purchase date.
Backyard Discovery Metal Play Structure
Backyard Discovery warrants this metal play product to be free from defects in materials and workmanship for a period of five (5) years from the original
date of purchase.
General Warranty Information
This warranty applies to the original owner and registrant and is non -transferable. Regular maintenance is required to ensure maximum life and
performance of this product. Failure by the owner to maintain the product according to the maintenance requirements may void this warranty.
Maintenance guidelines are provided in the Owner's Manual.
This Limited Warranty does not cover:
• Natural occurring properties of wood such as twisting, warping, checking, peeling or any other natural occurring properties of wood that do not
affect performance or
integrity.
• Installation — the warranty is null and void if installation is not in accordance with the
Assembly Instructions.
• Labor for any inspection
• Labor for replacement of any defective item(s)
•
Incidental or consequential damages
• Cosmetic defects, including rusting, color fading, minor cracks, corrosion, which do not affect performance or integrity of a part or the entire
product.
• Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable Assembly Manual.
• Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure.
• Improper installation including but not limited to installation on uneven, unlevel, or soft ground.
Backyard Discovery products have been designed for safety and quality. Any modifications made to the original product could damage the structural
integrity of the unit leading to failure and possible injury. Modification voids any -and -all warranties and Backyard Discovery assumes no liability for the
modified products or consequences resulting from failure of a modified product. Backyard Discovery disclaims all other representations and warranties
of any kind, express or implied.
This product is warranted for RESIDENTIAL USE ONLY.
Under no circumstance should a Backyard Discovery product be used in public settings
(public settings include but are not limited to churches, day cares, parks, etc.). Such use may lead to product failure and potential injury. Any and all
public use
will void this warranty.
USA and Canada: To make a warranty or replacement part claim please visit backyarddiscovery.com or call Backyard Discovery customer service at
800-856-4445. Backyard Discovery will, at its sole discretion, replace any part within the stated warranty period that is defective in workmanship or
materials. At Backyard Discovery's discretion, photographs of the defective part, physical return of the defective part to Backyard Discovery, or proof of
purchase may be required
for verification.
Outside of the USA and Canada: Contact place of purchase or distributor for warranty service.
This Warranty gives you specific legal rights. You may have other rights
as well which vary from state to state, province to province or country to
country, where you bought the product. This warranty excludes all consequential damages however, some
states do not allow the limitation or exclusion
of consequential damages and therefore this limitation may not apply to you.
Please read entire booklet completely before beginning the assembly process
Please retain these instructions and your receipt for future reference. Keep them in a safe place where you can refer to them as needed. In order to
provide you with the most efficient service, it is required that you provide us with the part numbers when ordering parts.
For
Your Records:
Please take time and fill out the information below. This information will be needed for warranty issues.
III
Where Purchased:
(Th
nmffla
Date of Purchase:
mgwal
Tradorig N.ber04/2012-S
Installation Date: P.O.#99999 1-100
Installed by:
RwARI
Utl
Tracking Number:
Tracking Number—,
Ci
Vertical ID Plate
Tracking Number Reference Label
Tracking ID number on the carton and on the bottom of the vertical ID plate are included for tracking purposes associated with warranty claims.
4
4

• • •
•• •• ••
• • •
Owner's Manual Operating Instructions and Safety Warnings
•••••
• • •
•• •
r 1
A
WARNING:
A BURN HAZARD
• Pay special attention to plastic and metal surfaces as
they may be hot enough to cause burns.
• Always check the temperature of the product before
NOTE: .
letting your children play on it.
• Remember that the product may cause burns if left
Your Children's Safety Is Our #1 Concern!
in direct sunlight.
Observe the following statements and warnings to reduce the likelihood
• Always be aware of the sun and weather conditions,
of serious or fatal injury. Please review these safety rules regularly with
and do not assume that the equipment is safe
your children.
because the air temperature is not very
high.
..
• Children MUST NOT use this playcenter until unit has been
• Instruct children to LOOK before they slide to make sure no
completely assembled and inspected by an adult to ensure
one is at the bottom.
set has been properly installed and anchored.
• DO NOT allow children to go down slide head first or run up
• Equipment is recommended for use by children 3 to 10 years
slide.
of age.
• DRESS CHILDREN APPROPRIATELY. (Examples would include
wearing well -fitting shoes and the avoidance of ponchos,
• This Playcenter is designed for a specific number of occupants
scarfs, and other loose -fitting clothing that is potentially
whose combined weight should not exceed the designated
hazardous while using equipment). Children must wear shoes
weight on the elevatedfloor or the swing area. The total unit
when using the play set. Do not allow children to wear open
capacity is outlined in the Basic Setup Dimensions section of toe or heel footwear like sandals, flip-flops or clogs.
instruction manual. The maximum fall height and
recommended play area is also available in the Basic Setup
• DO NOT allow children to
climb when the equipment is wet.
Dimensions section of the manual.
• Children should NEVER jump from a fort
deck. They should
• On -site, continuous adult supervision is REQUIRED. MOST
always use the ladder, ramp or slide.
SERIOUS INJURIES AND DEATHS ON PLAYGROUND EQUIPMENT
•
Children should NEVER be allowed to crawl or walk across the
HAVE OCCURRED WHILE CHILDREN WERE UNSUPERVISED!
top of monkey bars.
• DO NOT allow
children to walk close
to, in front
of,
behind, or
• DO
NOT allow children to crawl on top of a fort roof.
between moving swings or other moving playground
equipment.
• Verify that any suspended climbing ropes, chain, or cable are
secured at both ends and that they cannot be looped back
on
• DO NOT let children stand on swings.
themselves as to create an entanglement hazard.
•
• Children should NOT twist the chains and ropes and should
DO NOT let children attach items to the playground
not loop them over the top support bar, this could reduce the
equipment that are not specifically designed for use with the
strength of the chain or rope.
equipment. Items such as, but not limited to, jump ropes,
clothesline, pet leashes, cables and chain can cause a
• DO NOT let children push empty seats. The seat could hit
strangulation hazard.
them and cause serious injury.
• Children should NEVER wrap their legs around swing chain.
• Instruct and teach children to sit in the center of the swings
with their full weight on the seats.
• DO NOT allow children
to slide down the swing chain.
• DO NOT allow children to use the equipment in a manner
• Instruct children to remove their bike or other sports helmet
other than intended.
before playing on playground equipment.
• Instruct children NOT to get off equipment while it is in
• NEVER add extra length to chain or rope. The chains or ropes
motion.
provided are the maximum length designed for the swinging
element(s).
• Instruct children to ALWAYS go down slides feetfirst. Never
• On sunny and/or hot days, check the slide and other plastic
slideheadfirst.
rides to assure that they are nothot to the touch to cause
burns. Cool hot slide and rides with water and wipe dry prior to
using.
Modifications
• Modifications made by the consumer to the original activity toy shall be carried out according to the instructions of the manufacturer.
In particular, instructions shall be provided with kit/accessory about the installation of rope/nets concerning the minimum diameter,
the need for fixation at both ends, overall length, and positioning in relation to other structures.
5
5

• • •
•• • •
• • •
Owner's Manual Please Read This Before Starting Assembly
•••••
• • •
•• •
Positioning Your Playcenter Suggested Playground Surfacing
• The playcenter is designed to be installed on a level
• Do not install
home playground equipment over
surface by an adult with an adult helper. Place concrete, asphalt, packed earth, grass, carpet, or any
in a fl at area of your yard to minimize ground other hard surface. A fall onto a hard surface can
preparation. result in serious injury to the equipment user.
• Choose a level location for the
equipment. This can • Do not install
loose fill surfacing over hard surfaces
reduce the likelihood of the play set tipping over and
such as concrete or asphalt.
loose -fill surfacing material washing away during
heavy rains.
• Shredded bark mulch, wood chips, fine sand and fine
gravel, are added as shock absorbing materials after
• Place the equipment not less
than 6'-7" (2.0 m) from assembly. If used properly these materials can absorb
any structure or obstruction such as a fence, garage, some
of impact of a child's fall.
house, overhanging branches, laundry lines, or
electrical wires.
• All surface material should extend a minimum of
6'-7" (2.0
m) feet in all directions around the play area.
• Provide enough room so that the children can use the
equipment safely. For example, for structures with
• Do not apply playground surfacing until after the unit
multiple play activities, a slide should not exit in front
is completely constructed. Playset should not be built
of a
swing.
on top of surfacing.
• It is a good idea to place your playcenter in an area that
• Use containment, such as digging out around the
is convenient for adults to watch children at play.
perimeter
and/or lining the
perimeter with landscape
edging.
• Create a site free of obstacles that could cause injuries
— such as low overhanging tree branches, overhead
• Installations of rubber tiles or poured -in -place
wires, tree stumps and/or roots, large rocks, bricks and
surfaces (other than loose -fill materials) generally
concrete. Additional suggestions in the Suggested
require a professional and are not "do-it-yourself"
Playground Surfacing Section.
projects.
• Do not build your playset on top of surfacing
material.
• Shall use Playground Surfacing Materials (other than
loose -fill material) which comply with the safety
• Locate bare metal platforms and slides out of direct
standard ASTM F1292 Standard Specification of
sunlight to reduce the likelihood of serious burns. A slide
Impact Attenuation of Surfacing Materials within the
that faces north will receive the least direct sunlight.
Use Zone of Playground Equipment.
• Separate active and quiet activities from each other.
• Anchors
shall be placed as instructed to reduce
For example, locate sandboxes away from swings or
tipping hazards.
use a guardrail or barrier to separate the sandbox
from the
movement of the swings.
The following chart explains the fall height in feet from
which a life threatening head injury would not be expected
Critical Heights in feet (m) of Tested Materials
Material Uncompressed Depth Compressed Depth
6" (152mm) 9" (228mm) 12" (304mm) to 9" (228mm)
Wood Chips
7'
(2.13m) 10-12' (3.0-3.6m)
11'
(3.35m)
10' (3.05m)
Double -Shredded Bark Mulch 6' (1.83m) 10-12' (3.0-3.6m)
11'
(3.35m)
7'
(2.13m)
Engineered
Wood Fibers
6' (1.83m) 7' (2.13m) >12' (3.66m) 6' (1.83m)
Fine
Sand
5' (1.52m) 5' (1.52m) 9' (2.74m) 5' (1.52m)
Coarse Sand 5'
(1.52m)
5'
(1.52m)
6' (1.83m)
4' (1.22m)
Fine
Gravel
5'
(1.52m) 7' (2.13m)
10' (3.05m) 6' (1.83m)
Medium
Gravel 5' (1.52m) 5' (1.52m) 6' (1.83m) 5' (1.52m)
Shredded Tires* 10-12' (3.0-3.6m)
N/A N/A N/A
"This data is from tests conducted by independent testing laboratories on a 6 -inch depth of uncompressed shredded tire samples produced by four manufacturers. The tests reported
critical heights, which varied from 10 feet to greater than 12 feet. It is recommended that
persons seeking to install shredded tires as a protective surface request test
data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292.
6
6

•
••••
• •
• •
• Owner's Manual Please Read This Before Starting Assembly
• • •
••• •
APPENDIX A
The following information
is from the United States
X3.1.3.2 Do not install loose -fill surfacing over hard
ConsumerProductSafetyCommission'slnformation
surfaces such as concrete or asphalt.
X3.1.4 Poured -In -Place Surfaces or Pre -Manufactured
Sheet for playground surfacing material; also see
Rubber Tiles — You may be interested in using surfacing other than
the following website for additional information:
loose -fill materials — like rubber tiles or poured -in -place surfaces.
www.cpsc.gov
X3.1.4.1 Installations of these surfaces generally require a
professional and are not "do-it-yourself" projects.
X3. SECTION 4 OF
THE CONSUMER PRODUCT SAFETY
X3.1.4.2 Review surface specification before purchasing this
COMMISSION'S
OUTDOOR
HOME
PLAYGROUND SAFETY
type of surfacing. Ask the installer/manufacturer for a
report showing
HANDB 0
OK 9
that the product has been tested to the following safety standard:
X3.1
Select Protective Surfacing —One of the most ASTM F 1292 Standard
Specification for Impact Attenuation of
important
things you can do to reduce the likelihood of serious head Surfacing Materials within the Use
Zone of Playground Equipment.
injuries is to
install shock -absorbing protective surfacing under This report should show the
specific height for which the surface is
and around
your play equipment. The protective surfacing should intended to protect against
serious head injury. This height should
be
applied to a depth that is suitable for the equipment height in be equal to or greater than the
fall height - vertical distance between
accordance with
ASTM Specification F 1292. There are different a designated play
surface (elevated surface for standing, sitting,
types of surfacing
to choose from; whichever product you select, or climbing) and
the protective surfacing below - of your play
follow these guidelines: equipment
X3.1.1 Loose -Fill
Materials:
X3.1.4.3 Check the protective surfacing frequently for wear.
X3.1.1.1 Maintain a minimum depth
of 9 inches of loose-
X3.1.5 Placement — Proper placement and maintenance of
fi ll materials
such as wood mulch/chips, engineered wood fi ber protective
surfacing is essential. Be sure to:
(EWF), or shredded/recycled rubber mulch for equipment up to 8
X3.1.5.1 Extend surfacing at least 6 feet from the equipment
feet high; and 9
inches of sand or pea gravel for equipment up to 5 in all
directions.
feet high. NOTE: An initial fi ll level of 12 inches
will compress to
X3.1.5.2 For to -fro swings, extend protective surfacing in
about a 9 -inch
depth of surfacing overtime. The surfacing will also front of and behind the swing
to a distance equal to twice the height
compact,
displace, and settle, and should be periodically refilled to of the top bar from
which the swing is suspended.
maintain at least a 9 -inch depth.
X3.1.2 Use a minimum of 6
inches of protective surfacing
9 This information has been extracted from the CPSC publications
for
play equipment less than 4 feet in height. If maintained properly,
"Playground Surfacing — Technical Information Guide" and "Handbook
this should be adequate. (At depths less than 6 inches, the protective
for Public Playground Safety." Copies of these reports can be obtained by
material is too easily displaced or compacted.)
sending a postcard to the: Office of Public Affairs, U.S. Consumer Product
Safety Commission, Washington, D.C., 20207 or call the toll -free hotline:
1-800-638-2772.
NOTE:
Do not install home playground equipment over concrete,
asphalt, or any other hard surface. A fall onto a hard surface can
The
American Society for Testing and Materials takes no position respecting
result in serious injury to the
equipment user. Grass and
dirt
are
not
the
validity
of any parent right
asserted in
connection with any item
considered
protective surfacing because wear and environmental mentioned in this
standard. Users of this standard are expressly advised
factors can
reduce their
shock
absorbing effectiveness.
Carpeting
that determination of the validity of any
such parent rights, and
the risk of
and thin mats are generally not adequate protective surfacing.
infringement
of such rights, are entirely their own responsibility.
Ground level equipment such as a sandbox, activity wall, playhouse
or other equipment that has no elevated play surface - does not need
The standard is subject to revision at any time by the responsible technical
any protective surfacing.
committee and must be reviewed every fi ve years and if not revised, either
approved or withdrawn. Your comments are invited either for revision
X3.1.3 Use containment, such as digging out around the
of this standard or for additional standards and should be addressed to
perimeter
and/or lining the
perimeter with landscape edging. Don't
ASTM Headquarters. Your comments will receive careful consideration at
forget to account for water drainage.
a meeting of the responsible technical committee, which you may attend.
X3.1.3.1 Check
and maintain the depth of the loose- If you feel that your
comments have not received a fair hearing you should
fi ll surfacing
material. To maintain the
right amount
of loose
-fill
make your
views known
to the ASTM
Committee on
Standards. 100
Barr
materials,
mark the correct level on play equipment support posts.
Harbor Drive, West Conshohocken, PA 19428.
That way you can easily see when to replenish and/or redistribute
the
surfacing.
7
7

• • •
•• •• ••
• • •
Owner's
Manual
Instructions for Proper Maintenance
• • •
• •
••••••
IT IS IMPORTANT TO CHECK AND TIGHTEN ALL HARDWARE AT THE BEGINNING AND DURING
THE SEASON AS THEY MAY LOOSEN DUE TO WOOD EXPANSION AND CONTRACTION.
At the
beginning of each play season Additional Maintenance
• Tighten all hardware. • Check the swing beam and hardware every two
• Lubricate all metallic moving parts per manufacturer's weeks due to wood expansion and contraction. It is
instructions. particularly important that this procedure be followed
• Check all protective coverings on bolts, pipes, edges, at the beginning of each season.
and corners. Replace if they are loose, cracked, or • Inspect wood parts monthly. The grain of the wood
missing. sometimes will lift in the dry season causing splinters
• Check all moving parts including swing seats, to appear. Light sand may be necessary to maintain a
ropes, cables, and chains for wear, rust, or other safe playing environment. Treat your playset with stain
deterioration. Replace as needed.
regularly, to help prevent
severe checking/splitting and
• Check metal parts for rust. If found, sand and other weather damage.
repaint using a non lead -based paint meeting the
.
A
waterborne transparent stain
has been
applied to
requirements of 16 CFR 1303. your playset. This is done for color only. Once or twice
• Check all wood members for deterioration a year, depending on your climate conditions, you must
and splinters. Sand down splinters and replace apply some type of protection (sealant) to the wood
deteriorating wood members. of your unit. Prior to the application of
sealant, lightly
• Reinstall any plastic parts, such as swing seats or any sand any "rough" spots on your playset. Please note this
other items that were removed for the cold season. is a requirement of your warranty.
• Rake and check depth of loose fi ll protective surfacing • Assembling and maintaining the playset on a level
materials to prevent compaction and to maintain location is very important. As your children play, your
appropriate depth. Replace as necessary. playset will slowly dig its way into the soil, and it is very
important that it settles evenly. Make sure the playset is
Twice a month
during play season
level and true one each year or at the beginning of each
play season.
•
Tighten all hardware.
• Check all protective coverings on bolts, pipes, edges, &
Disposal Instructions
corners. Replace if they are loose, cracked, or missing.
• Rake and check depth of loose fi ll protective surfacing
When the
Playcenter use is no longer
materials to prevent compaction and to
maintain desired, it should be disassembled
appropriate depth. Replace as necessary.
and disposed of in such a way that no
unreasonable hazards will exist at the •
Once a month during play season.
time the unit is discarded.
• Lubricate all metallic moving parts per manufacturer's
Third Party
Assembly
instructions.
• Customer may, in their sole discretion, elect to use a
• Check all moving
parts including swing seats,
third party person or service to assemble this product.
ropes, cables, and chains for wear, rust, or other
Backyard Discovery assumes no responsibility or
deterioration. Replace as needed.
liability for any charge incurred by the Customer for
any assembly services. Please see our warranty for
more information about damaged and missing part
At the end of each season or when
replacement coverage. Backyard Discovery will not
the temperature drops below 32° F
reimburse Customer for the price of parts purchased
• Modifications made by the consumer to the
original
• Remove plastic swing seats and other items as specified by
activity toy shall be carried out according to the
the manufacturer and take indoors or do not use.
instructions of the manufacturer. In particular, instruc-
• Rake and check depth of loose fi ll protective surfacing
tions shall be provided with kit/accessory about the
materials to prevent compaction and to maintain
installation
of rope/nets
concerning the minimum
appropriate depth. Replace as necessary.
diameter, the need for fixation
ends, overall length,
and
positioning in relation to other at both structures.
OWNERS SHALL BE RESPONSIBLE FOR MAINTAINING THE LEGIBILITY OF THE WARNING LABELS
8
8

• • •
•• •• ••
• • •
Owner's
Manual
Instructions for Proper Maintenance
• • •
• • •
• • •
Your Backyard Discovery structure is designed and constructed of quality
materials. As with all outdoor
products it will weather and wear. To maximize
the enjoyment, safety and life of your structure it is important that you properly
maintain it.
About Our Wood
Backyard Discovery uses 100% Cedar (C. Lanceolata) wood. Although we take great care in
selecting the best quality lumber available, wood is still a product of nature and susceptible to
weathering which can change the appearance of your set.
What causes weathering? Does it affect How can I reduce the amount of
the strength of my product? weathering to wood product?
One of the main reasons for weathering is the 1. Your wood product is coated with a water -
effects of water (moisture); the moisture content based stain. Sunlight will break down the coating,
of the wood at the surface is different than the so we recommend applying a water
repellent or
interior of the wood. As the climate changes, stain on a yearly basis (see your local stain and
moisture moves in or out of the wood, causing
paint
supplier for a recommended product). You
tension which can result in
checking and or
must apply some type of protection (sealant)
warping. You can expect the following due to to the wood of your product. Please note this
weathering. These changes will not affect the
is
a requirement of your warranty. Most
strength of the product: weathering is just the normal result of nature
and will not affect safety. However if you are
1.
Checking is surface cracks in the wood along the concerned that a part has experienced a severe
grain. A post (4" x 4") will experience
more checking weathering problem please call our customer
than a board (1" x 4") because the surface and service department for further assistance.
interior moisture content will vary more widely than
in
thinner wood. 2. Inspect wood parts
monthly. The grain of
the wood sometimes will lift in the dry season
2. Warping results from
any distortion (twisting, causing splinters to appear.
Light sanding may
cupping) from the
original plane of the board and be necessary to maintain a safe
environment.
often happens from rapid wetting and drying of
the
Treating your Product with protection (sealant)
wood. after sanding will help prevent severe
checking/
splitting and other weather damage.
3. Fadinghappens as a natural change in the wood
color as it is exposed to sun -light and
will turn grey
over
time.
9
9

• • •
•• • •
•• ••
• Owner's Manual Assembly Tips
•••••
• • •
• • •
A\Protrusion Hazard
Incorrect Correct
If you see exposed
threads and your bolt
protrudes beyond the
T -Nut you may have over
-
tightened the bolt or
used incorrect hardware.
If you've overtightened,
remove the bolt and add
washers to eliminate the
protrusion.
1/8"
Proper
Hardware Assembly
-
BOLT
Bolt and T -Nut Assembly
Tap T -nut into the provided hole. Insert your bolt through the
lock washer and insert into the provided hole opposite from the
T -Nut. Turn clockwise to thread into T -nut. Do not completely
tighten until instructed.
-to
LOCK WASHER
Bolt and Barrel Nut
Assembly
—BOLT
Insert barrel nut through the lock washer and press the pair
4 0
through the provided hole. Insert your bolt through the second
i
BARREL NUT
lock washer and insert the pair into the provided hole opposite
LOCK WASHER
from the barrel
nut. Turn clockwise to thread into the barrel nut.
Do
not completely tighten until instructed.
LOCK WASHER
Lag Assembly
-LAG SCREW
Normally there will be a
pre -drilled pilot hole on assemblies
that require a Lag Screw. If there is no pilot hole, line up the two
boards as they are to be attached and use the factory drilled hole
as a guide to drill another pilot hole into the adjoining board.
This will keep the wood
from splitting. Only a lock washer is
required for steps with Lag Screws.
LOCK WASHER
10
10

• • •
•• • •
• • •
Owner's Manual Assembly Tips
•••••
• • •
•• •
n ASSEMBLY TIP:
V Keep an eye out for these boxes which will contain helpful pictures and information making the
assembly process as quick and painless as possible.
Sorting
Wood
41D.,
IN ink
%Aft
0 Ask
When removing the wood from the boxes we recommend arranging them by part number before you begin
assembly. This will allow for faster assembly and easily identify any parts that may be missing or damaged.
Sorting Hardware
NUT BARREL SCREW T -NUT WASHER FLAT BOLT HEX BOLT SCREW PWH
H100545 H100695 H100699 H100706 H100716 H100718 H100742
I!
To help with assembly we recommend sorting your hardware bags with the seven digit alpha -numeric number printed
on the bags or by hardware type (i.e. bolts, nuts, etc.). Organizing your hardware will make assembly easier.
Hardware Identification
•
Hardware bags are printed with
a seven digit alpha
-numeric part
A\\\\\\\\
number. During
assembly you only
need to reference the last three digits
1 92 (x2)
378
BOLTWH 1990O
of the part number aS noted in each
(x2)
5/16
x 1-3/4
- H100378
step. This
will make fi nding the
correct hardware easier.
378(x2) 198(x2)
11
11

Basic
Setup
Dimensions
Place the set on level ground, not less than 6.6 ft [2 m] from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines,
or electrical wires.
6.6 ft Safe
Play Zone
[2.0 m]
'< > - • - - - < >
33
22.28
ft
5-
10.29 ft
[6.8 m]
[3.1 m]
-.I
6.6 ft
[2.0m]
12.95 ft
[3.9 m]
24.8
ft
[7.6 m]
General Information:
Your set has been designed and engineered for
children only and for residential use only.
•1
,
A maximum of 150 lbs. per child is recommended for
play activities designed for individual use.
9.04 ft
A maximum of 120 lbs. per child is recommended for [ 2 . 8 m]
6.08
play activities designed for multiple child use.
[1.9
ft
m]
A maximum of 9 children is recommended for this
1 \_)
swing set.
Important Assembly Notes
Safe play
height:
15.04'[4.6
m]
Maximum fall height:
6.08' [1.9 m]
1) While assembling unit, take time before and after each step to make sure fort is level. If fort is
not level, assembly
will be difficult and improper assembly may result. Extra care must be taken to
ensure the fort is square.
2) Tighten bolts securely, tighten nuts on bolts flush to the tube or member.
3) Pay close attention to the ITEMS NEEDED FOR EACH STEP. They
can be a valuable aid when
sorting your wood and hardware. Assembly will be made easier if items are sorted by step.
4) Pay close attention to make sure you are using the correct hardware in the correct steps. Using
incorrect
hardware may result in improper assembly.
5) Whenever a T -nut is used, follow these
directions. Place T -nut in pre -drilled hole. Tap in with hammer.
Place bolt with washers in the opposite side. Hand tighten to make sure the bolt is in the T -nut.
DO
NOT over tighten.
6) Read the steps of each step thoroughly. The written steps may include
important information not
shown in the
illustrations.
12
12

Tools Required for Installation:
(These are the tools that are generally required for assembly of our outdoor products.
These tools are not included with the outdoor product purchase.)
E l yi I I@I ie
El
1 ' 0
(Phillips Screw Driver)
(Level 24")
(Open
End Wrenches 1/2")
(Square)
(Tape Measure)
(Claw Hammer)
(Rubber Mallet - Optional)
'
4; p,
i t i
re
i 1
I
SO
I -11—I
1-->
(Cordless Drill or
(Drill Attachments: (3/8" D ri ve R a t c h e t, 1/2" STD S oc k e t s
Electric Drill)
Phillips Head, Socket 1/2" D ee p S oc k e t s )
Driver)
_
/
•Vil
A
/
i
(An Adult w/ an Adult
(1/8", 7/16" & 3/8"
(Ladder)
Drill
Bits)
Helper)
Icons and their uses you will see throughout this manual
l
When you see this icon you will need
You will need to make sure that your
assembly is square before tightening a h )
your bolts.
I
Ap e
a socket wrench. The icons below show
10O
the size of attachments needed for
assembly 1/2.
0 11
24 „
For
proper
assembly you
will need to
d e
This icon warns you to not over tighten
ensure that your structure is level before
ilt4 your bolts. This is to prevent structural
proceeding to the next step. damage and also splintering your wood.
_____
Some steps in the assembly process will
require an extra set of hands. Make sure e
you have a helper available.
_--. A ladder will be needed for assembly.
/—___I
Do NOT stand on the set when it is
incomplete, unstable, and not anchored.
}
Failure to do so
may result in injury.
This icon will show you what drill
CA) 1 This icon shows the size of an open attachments are needed. For thi s
ended wrench. Using the wrench as the
r
.....
example you will need a Phillips head
fraction bar.
attachment and 3/8 drill bit.
3 0"‘ i O
/8
13
13

Parts
Identification
Wood
Components
(NOT TO SCALE)
0 . 0
El- LOWER UPRIGHT - W4L07312
(1 )
1 3/8"x3 3/8"x42 3/4"
(36x86x1087)
, E2- UPPER UPRIGHT - W4L 15659
1 3/8"x3 3/8"x38 7/8" (36x86x989)
°
•
(1) E3 - LOWER UPRIGHT - W2A02877
1 3/8"x3 3/8"x42 3/4" (36x86x1087)
0 • 0 0 0 0
1
E4- UPPER UPRIGHT - W4L07298
1 3/8"x3 3/8"x38 7/8" (36x86x989)
•
0 0 0
°•°
E5- LOWER UPRIGHT - W4L07248
``i 1 3/8"x3 3/8"x42 3/4"
(36x86x1087)
0 0 0
1 1
E6- UPPER UPRIGHT - W4L
15658
`" 1 3/8"x3 3/8"x38 7/8" (36x86x989)
0
E9- UPPER ANGLE BRACE BOARD - W4L07239
``i 1
3/8"x3 3/8"x34 1/8" (36x86x866)
•
°
„, E10- LOWER ANGLE BRACE BOARD - W4L07241
(-) 1 3/8"x3 3/8"x46" (36x86x1168)
•
Ell- UPPER UPRIGHT - W4L07307
`-`) 1 3/8"x3 3/8"x38 7/8" (36x86x989)
,...••••
0 \
/ •
Gl- END SUPPORT - W4L 12368
Y -1 1"x5 1/4"x42 7/8"
(24x134x1090)
• •
, H1- FLOOR RAIL - W4L07297
" ) 1"x3 3/8"x36 1/8"
(24x86x919)
•
•
H2- FLOOR RAIL - W4L07251
`') 1"x3 3/8"x36 1/8" (24x86x919)
1
H3- FLOOR SUPPORT - W4L07255
1"x3 3/8"x36 1/8"
(24x86x919)
, H4- WALL RAIL - W4L07267
1"x3 3/8"x35 3/8" (24x86x898)
°
H5- DECK BRACE - W4L07273
1"x3 3/8"x18 3/4" (24x86x476)
/°
H6- DECK BRACE - W4L07276
,„``i 1"x3 3/8"x13 3/4"
(24x86x350)
14
14

Parts
Identification
Wood
Components
(NOT TO SCALE)
,„ H7- BENCH GROUND BOARD - W4L07282
) 1"x3 3/8"x16 7/8"
(24x86x430)
„, H8- BENCH UPRIGHT - W4L07284
`i 1"x3 3/8"x11
3/4" (24x86x300)
L)
,„ H9- BENCH SEAT SUPPORT - W4L07283
)
1"x3 3/8"x6 1/2" (24x86x166)
0 0
,,,
H10- ROOF SUPPORT - W4L15027
1"x3 3/8"x29 1/2" (24x86x748)
°
, H11- WALL RAIL - W4L 15024
1
1"x3 3/8"x35 3/8" (24x86x898)
„, H12- ROOF BOARD - W4L 15025
`) 1"x3 3/8"x27 7/8"
(24x86x709)
, J1- WALL BOARD - W4L07288
1"x2
3/8"x36 5/8" (24x60x930)
J2- LADDER RAIL - W4L07287
1"x2 3/8"x46 3/8" (24x60x1177)
• •
1 4
„, J3- LADDER RAIL - W4L07265
1"x2
3/8"x46 3/8" (24x60x1177)
,„ J4- AWNING BOARD - W4L 15019
1"x2 3/85c14 1/8"
(24x60x358)
„) J5- AWNING SUPPORT - W4L06908
``I 1"x2 3/8"x11 3/4"
(24x60x298)
„ J6- LADDER RAIL - W4L 15023
1"x2 3/8"x46 3/8" (24x60x1177)
J7- LADDER RAIL - W4L07268
(1)
1"x2 3/8"x46 3/8" (24x60x1177)
,„ J8- SHELF SUPPORT - W4L07058
``i 1"x2 3/8"x3 3/8" (24x60x86)
•
•
1
, Kl- SERVING SHELF- W4L07271
5/8"x5 1/4"x35
3/8" (16x134x898)
0 0
•
0 0
•
, K2- WALL BOARD - W4L07316
1
5/8"x5 1/4"x20 1/8" (16x134x510)
• •
• •
, K3- WALL BOARD - W4L07303
1 5/856 1/45O8 3/8" (16x134x466)
15
15

Parts Identification
Wood
Components
(NOT TO SCALE)
. .
„, M1- GROUND BOARD - W4L07252
''' 5/8"x3 3/8"x36 1/8" (16x86x919)
0
O
'\
M2- GROUND BOARD - W4L07299
„
Y
-1,
5/8"x3 3/8"x31 5/8" (16x86x802)
• •
• •
M3- LADDER RUNG - W4L07520
'-) 5/8"x3 3/8"x19 1/4"
(16x86x489)
•
• °
•
M4- LADDER RUNG - W4L 15032
,„ `' - 'i 5/8"x3 3/8"x19 1/4" (16x86x489)
I :
O
O
\
M5- GROUND BOARD - W4L 15021
- `i 5/8"x3 3/8"x23 1/4"
(16x86x591)
I :
°
o \
,
M6- GROUND BOARD - W4L 15022
"-
i 5/8"x3 3/8"x23 1/4" (16x86x591)
0
•
0
O
•
0
, M7- FLOOR RAIL - W4L07254
" )
5/8"x3 3/8"x37 1/4" (16x86x946)
0
. .
M8- WALL BOARD - W4L07269
'-) 5/8"x3 3/8"x36 1/8" (16x86x919)
O
o A
, M9- GROUND BOARD - W4L 15031
` - ` i 5/8"x3 3/8"x31 5/8" (16x86x802)
0
. .
„, M10- GROUND BOARD - W4L07286
`' - i 5/8"x3
3/8"x371/2" (16x86x951)
0 0
,i M11- FLOOR RAIL - W4L07275
`" 5/8"x3 3/8"x37 1/4" (16x86x946)
. .
„, M12- TARP SUPPORT - W4L 15033
`i 5/8"x3 3/8"x37 3/4" (16x86x959)
O 0
,,, M13- ROOF BOARD - W4L 15026
``i 5/8"x3 3/8"x27 7/8"
(16x86x709)
. .
M14- TARP SUPPORT - W4L 15028
1)
5/8"x3 3/8"x36 1/8" (16x86x919)
,i , M16- GROUND BOARD - W4L 15030
`-`)
5/8"x3 3/8"x35 3/8" (16x86x898)
.
°
•
.
M17- FLOOR BOARD - W4L 12364
(1)
5/8"x3 3/8"x37 1/4" (16x86x946)
16
16

Parts Identification
Wood
Components
(NOT TO SCALE)
. .
„, M18- BENCH SEAT - W4L07098
``i 5/8"x3
3/8"x23 1/2" (16x86x598)
. .
„, M19- WALL RAIL - W4L07306
`) 5/8"x3 3/8"x35 3/8" (16x86x898)
. .
M20- WALL RAIL - W4L07309
' - i 5/8"x3
3/8'x371/2" (16x86x951)
. .
M21- WALL BOARD - W4L07315
1) 5/8"x3 3/8"x36 1/8" (16x86x919)
•
, a , M22- WALL BOARD - W4L07302
m 5/8"x3 3/8"x19 5/8" (16x86x500)
M23- WALL BOARD - W4L07314
(
„
`') 5/8"x3 3/8"x18 3/8" (16x86x466)
.
°
. .
M77- SLIDE BRACE - W4L 12363
'-) 5/8"x3 3/8"x14 1/4"
(16x86x362)
. .
M78- CENTER SLIDE BRACE - W4L 12362
`'' 5/8"x3 3/8"x14 1/4" (16x86x362)
. .
N1- SAFETY BOARD - W4L07041
- ' 1 5/8"x2 3/8"x35 3/8" (16x60x898)
. .
,i , N2- SAFETY BOARD - W4L07263
`" 5/8"x2 3/8'x371/2" (16x60x951)
, n , N4- PICKET - W4L07301
5/8"x2 3/8"x18 3/8" (16x60x466)
- -
(1 , N7- AWNING BOARD - W4L 15020
'' 5/8"x2 3/8"x28 5/8"
(16x60x726)
I° °I
O1- PICKET - W4L07517
''' 5/8"xl 3/8"x18 3/8" (16x34x466)
I• • I
„, O2- PICKET - W4L07056
` 1 5/8"xl 3/8"x19 5/8" (16x34x500)
I ° • I
(1 , O3- SAFETY BOARD - W4L07093
`' - i 5/8"xl 3/8"x35 3/8" (16x34x898)
I • • I
fi , O4- AWNING BOARD - W4L07053
'-) 5/8"xl 3/8"x26 5/8"
(16x34x676)
I °
(,, O1- SWING BEAM GROUND BOARD - W4L07242
``) 1"x4 3/8"x45 5/8" (24x112x1160)
17
17

Parts Identification
Wood
Components
(NOT TO SCALE)
ad a
if if °if. \ ' c i 1r if if
0H I
II II ll 0
SB1- SWING BEAM - W4L07244 , SB2- SWING BEAM - W4L07243
"I 5 1/4"x2"x46" (134x50x1168) (1)
5 1/4"x2"x46"
(134x50x1168)
0
<-
/
(1 Ti- ATTACHMENT BOARD - W4L07518
„, T2- SAFETY BOARD - W4L 12369
`" 1"xl 3/8"x4 3/4" (24x34x120)
``i 1"xl 3/8"x15 1/2" (24x34x394)
I
n n n o n .
.
_
(1 , W2- SWING BEAM SUPPORT - W4L07238
. . . .
` - `i 2"x3 3/8"x46" (50x86x1168)
. . . .
• •
.
• •
(2) FP1 - FLOOR PANEL - W2A 02023
1 1/4"x17"x37 1/4" (32x432x946)
Parts Identification
Hardware
( .
.1111111=
1 1
"m1111011111111
(1) - BOLT WH 5/16x4 1/2 -
H100021
(34) - BOLT WH
5/16x2 - H100012
(
111111101011M1 1
IIII - 1
" Ill i
l"" \ "l i
\ -e
(2) - BOLT WH 5/16x4-1/4
- H100166
(25)
-
BOLT WH 5/16x1 3/4 - H100011
i
l;,
•
r illEMU
-'
••
:"", I
ll
tl
V \ \ \ \
1 \
\ I
(2) - BOLT WH 5/16x3 -
H100016
- -
(10) - BOLT WH 5/16x1 1/2 - H100010
c
i
-----
6 1
-,
_ _ _ _Ialailli "I "H
°
00 "
(7) - BOLT WH 5/16x2 1/2 - H100014
,_-
71___ Jamitaimag __ l '
IlliMIlli
_
(9) - BOLT WH 5/16x1 1/4 -
H100009
_ __
(26)
-
BOLT
WH 5/16x1/2 -
H100115
I
. . „ . .. . . .....
[W1101111 11
(13) - BOLT WH 5/16x2 1/4 - H100013
(7)
- BOLT WH 5/16x1
- H100008
18
18

Parts Identification
Hardware
- T-40 TORX WRENCH - A100041
(1)
(1) - T-40 TORX BIT - A100042
(1) - T-30 TORX WRENCH - H100114
(1) - T-30 TORX BIT - H100147
- NUT BARREL WH 5/16x5/8 - H100004
(4)
- NUT BARREL WH 5/16x7/8 - H100005
(32)
- NUT BARREL WH 5/16x1 1/2 - H100006
(4)
- NUT BARREL WH 5/16x1 3/4 - H100007
(2)
- NUT BARREL WH 1/4x5/8 - H100136
(12)
- LAG SCREW WH 5/16x1 1/2 - H100026
(4)
- LAG SCREW WH 5/16x2 - H100027
(15)
- LAG SCREW WH 5/16x2 1/2 - H100028
(7)
- LAG SCREW WH 1/4x1-1/2 - H100145
(12)
- WASHER LOCK EXT 8x19 - H100030
(114)
- WASHER LOCK EXT 12x19 - H100031
(36)
- WASHER SPLIT 5/16 - H100095
(4)
- WASHER SAFETY 17x30 - H100103
(4)
- WASHER FLAT 8x27 - H100105
(15)
- WASHER FLAT 9x18 - H100106
(4)
- WASHER LOCK INT 8x15 - H100108
(15)
- WASHER LOCK EXT 6x15 - H100138
(12)
- WASHER LOCK EXT 8x15 - H100139
(12)
- T-NUT 1/4 - H100072
(23)
- T-NUT 5/16 - H100074
(91)
- NUT LOCK 5/16 - H100110
(9)
- NUT BARREL WH 1/4x7/8 - H100140
(4)
19

Parts Identification
Hardware
- BOLT HEX 5/16x1 1/4 - H100042
(4)
- BOLT HEX 5/16x2-3/4 - H100047
(2)
- BOLT PTH 1/4x1 1/4 - H100062
(2)
- BOLT PTH 1/4x3/4 - H100063
(11)
- SCREW PFH 8x1-1/4" - H100087
(29)
- SCREW PFH 8x1-1/8" - H100088
(64)
- SCREW PFH 8x1-3/4" - H100089
(9)
- SCREW PFH 8x2 1/2 - H100090
(35)
- 9 1/2" SWING HANGER QUICK LINK - H100099
(6)
- SCREW TAPPING 14x2 - H100081
(2)
- SCREW PFH 8x2 - H100111
(4)
- SCREW PWH 8x5/8 - H100128
(15)
- BOLT WH 1/4x1/2 - H100141
(4)
- BOLT WH 1/4x1-1/2 - H100143
(4)
- BOLT WH 1/4x5/8 - H100490
(18)
- SCREW PFH 8x1-1/2" - H100086
(46)
- SCREW PWH 8x1-1/2 - H100207
(4)
- SCREW SETTER - H100764
(1)
- MAGNETIC DRIVER - H101100
(1)
20