Backyard Products YardLine 4276 User manual

Call Us First!
DO NOT RETURN TO STORE.
For immediate help with assembly or product information
call our toll-free number:
1-800-844-9273
or email:
[email protected]
Our staff is ready to provide assistance.
April through October M - F 8:00 AM to 7:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
16644PLAY
STOP!
STOP!

ASSEMBLY INSTRUCTIONS
Email us at: [email protected] or call us at 1-800-844-9273
Printed in USA
Customer Service
1-800-844-9273
1000 Ternes Drive
Monroe, MI 48162
16644PLAY
A Backyard Products Company
Model: 4276
4369
6007
6192
IMPORTANT!!
PLEASE READ BEFORE BEGINNING ASSEMBLY!!
Please make sure all lumber, hardware and accessory parts are accounted for.
If you are missing anything, please DO NOT RETURN to the store where purchased.
Please call our Customer Service Department at the number below.
LDR 02-20-2018

2
Safety Checklist for Play Sets and Accessories
IMPORTANT!
This product is intended for single family home/residential use only and not intended for use in any
public setting. Placement in any public setting constitutes a misuseof this product.
Observing the following statesments and warnings reduces the likelihood of serious or fatal injury
 Thisplaysethasbeendesignedforusebyamaximumofeleven(11)occupantsatonetimehavinga
 combinedweightof1,155pounds.
 Thisplaysetisintendedforusebychildrenfrom(2)to(10)yearsofage.
 On-siteadultsupervisionforchildrenofallagesisrecommended.
 Instructchildrennottowalkcloseto,infrontof,behind,orbetweenmovingitems.
 Instructchildrennottotwistswingchainsorropesorloopthemoverthetopsupportbarsincethismay
reducethestrengthofthechainorrope.
 Instructchildrentoavoidswingingemptyseats.
 Teachchildrentositinthecenteroftheswingswiththeirfullweightontheseats.
 Instructchildrennottousetheequipmentinamannerotherthanintended.
 Instructchildrennottogetoffequipmentwhileitisinmotion.
 Donotallowchildrentowearinappropriateitems,suchasbutnotlimitedto,loosefittingclothing,hood
 andneckdrawstrings,scarves,cord-connecteditems,capesandponchos.Theseitemscancause
 deathbystrangulation.
 Instructchildrennottoclimbwhentheequipmentiswet.Slipperysurfacesmaycauseahazard.
 Verifythatsuspendedclimbingropes,chain,orcablearesecuredatbothends.
 Verifythatsuspendedclimbingropes,chain,orcablecannotbeloopedbackonitself.
 Instructchildrennottoattachitemstotheplaygroundequipmentthatarenotspecificallydesignedfor 
usewiththeequipment,suchas,butnotlimitedto,jumpropes,clothesline,petleashes,cablesand 
chainastheymaycauseastrangulationhazard.
 Instructchildrentoremovetheirbikeorothersportshelmetbeforeplayingontheplaygroundequipment.
 Dresschildrenwithwell-fittingandfullfootenclosingfootwear.Examplesofinappropriatefootwearare
 clogs,flipflops,andsandals.
 Instructchildrentonotwalkorrunupslides.
 Instructchildrentonotpickupslidesorrampsasthismaycausedamageorbreakage.
 Placetheequipmentonlevelgroundnotlessthansix(6)feetfromanyobstructions.Besuretolook 
overheadforanyobstructionsabovetheplayset.
 Donotusetheequipmentuntilfullyerectedperthisplaysetinstructionmanual,boltstightenedand
 theplaysetisanchoredtotheground.
A Backyard Products Company

3
PLAYSET MAINTENANCE

Tightenallhardware.
Lubricateallmetallicmovingpartspermanufacturer'sinstructions.
Checkallprotectivecoveringsonbolts,pipes,edges,andcorners.Replaceiftheyareloose,cracked,ormissing.

Checkallmovingpartsincludingswingseats,ropes,cables,andchainsforwear,rust,orotherdeterioration.Replaceasneeded.
Checkmetalpartsforrust.Iffound,sandandrepaintusinganonleaded-basedpaintmeetingtherequirementsof16CFR1303.
Checkallwoodmembersfordeteriorationandsplinters.Sanddownsplintersandreplacedeterioratingwoodmembers.
Reinstallanyplasticparts,suchasswingseatsoranyotheritemsthatwereremovedforthecoldseason.
Rakeandcheckdepthofloosefillprotectivesurfacingmaterialstopreventcompactionandtomaintainappropriatedepth.Replaceasnecessary.



 
Tightenallhardware.

 Checkallprotectivecoveringsonbolts,pipes,edges,andcorners.Replaceiftheyareloose,cracked,ormissing.

 Rakeandcheckdepthofloosefillprotectivesurfacingmaterialstopreventcompactionandtomaintainappropriatedepth.Replaceasnecessary.



Lubricateallmetallicmovingpartspermanufacturer'sinstructions.

 Checkallmovingpartsincludingswingseats,ropes,cables,andchainsforwear,rust,orotherdeterioration.Replaceasneeded.

 Removeplasticswingseats,tents,sandboxcover,tireswing,slideandotheritemsasspecifiedbythemanufacturerandtakeindoorsor
donotuse.

 Rakeandcheckdepthofloosefillprotectivesurfacingmaterialstopreventcompactionandtomaintainappropriatedepth.Replaceasnecessary.
Ownershallberesponsibleformaintaingthelegibilityofwarninglabels.

When you are ready to dispose of your playset, make sure that all metal, plastic and wood components are disposed of in accordance
with local waste ordinances.

Buyer and/or owner should disassemble and dispose of the playground equipment in such a way that no unreasonable hazards will
exist at the time the swing set is discarded. Do not burn your playset's preserved wood.
At the beginning of each play season:
Twice a month during play season:
Once a month during play season:
PLAYSET CHECKLIST
For further information on playground safety, the Consumer Product Safety Commission(CPSC) publishes the Outdoor
Home Playground Safety Handbook which can be downloaded for free from www.cpsc.gov. An additional resource is the
American Society of Testing and Materials (ASTM)Standard Consumer Safety Performance Specification for Home Play-
ground Equipment (ASTM F1148) which can be purchased and downloaded from www.astm.org.
Cosmeticdefectsthatdonotaffectthestructuralintegrityoftheproduct,ornaturaldefectsofwoodsuchaswarping,
splitting,checking,twisting,shrinkage,swellingoranyotherphysicalpropertiesofwoodthatdonotpresentasafety
hazard,arenotcoveredbyourwarranty.
Tohelpminimizethesenaturaldefectswerecommendapplyingasealerorstaineverytwoorthreeyears,ormoreoften
astheclimatedictates.Powerwashing,sandingorotherpreparatorymethodsshouldbeusedpriortosealingorstaining.
Periodicmaintenanceisrequiredtoensuresafeenjoymentofyourplaysetandaccessories.ReadandfollowthePlayset
Checklistbelowtoreducethelikelihoodofseriousorfatalinjury.Usethechecklistsasaguideforproperplaysetcare
andmaintenance.
At the end of each play season or when the temperature drops below 10F:

4
PLAYGROUND SURFACING MATERIALS
SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION'S OUTDOOR HOME
PLAYGROUND SAFETY HANDBOOK9
Select Protective Surfacing
Oneofthemostimportantthingsyoucandotoreducethelikelihoodofseriousheadinjuriesistoinstallshock-absorbingprotectivesurfacingunderand
aroundyourplayequipment.TheprotectivesurfacingshouldbeappliedtoadepththatissuitablefortheequipmentheightinaccordancewithASTM
SpecificationF1292.Therearedifferenttypesofsurfacingtochoosefrom;whicheverproductyouselect,followtheseguidelines:

NOTE:Donotinstallhomeplaygroundequipmentoverconcrete,asphalt,oranyotherhardsurface.Afallontoahardsurfacecanresultinserious
injurytotheequipmentuser.Grassanddirtarenotconsideredprotectivesurfacingbecausewearandenvironmentalfactorscanreducetheir
shockabsorbingeffectiveness.Carpetingandthinmatsaregenerallynotadequateprotectivesurfacing.Groundlevelequipment-suchasa
sandbox,activitywall,playhouseorotherequipmentthathasnoelevatedplaysurface-doesnotneedanyprotectivesurfacing.
Maximum fall height for this playset is 83''.
Loose-Fill Materials:
Maintainaminimumdepthof9inchesofloose-fillmaterialssuchaswoodmulch/chips,engineeredwoodfiber(EWF),orshredded/recycled
rubbermulchforequipmentupto8feethigh;and9inchesofsandorpeagravelforequipmentupto5feethigh.NOTE:Aninitialfilllevelof
12incheswillcompresstoabouta9-inchdepthofsurfacingovertime.Thesurfacingwillalsocompact,displace,andsettle,andshouldbe
periodicallyrefilledtomaintainatleasta9-inchdepth.
Useaminimumof6inchesofprotectivesurfacingforplayequipmentlessthan4feetinheight.Ifmaintainedproperly,thisshouldbeadequate.
(Atdepthslessthan6inches,theprotectivematerialistooeasilydisplacedorcompacted.)
Usecontainment,suchasdiggingoutaroundtheperimeterand/orliningtheperimeterwithlandscapeedging.Don'tforgettoaccountforwater
drainage.
Checkandmaintainthedepthoftheloose-fillsurfacingmaterial.Tomaintaintherightamountofloose-fillmaterials,markthecorrectlevelonplay
equipmentsupportposts.Thatwayyoucaneasilyseewhentoreplenishand/orredistributethesurfacing.
Do notinstallloosefillsurfacingoverhardsurfacessuchasconcreteorasphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles:
Youmaybeinterestedinusingsurfacingotherthanloose-fillmaterials-likerubbertilesorpoured-in-placesurfaces.
Installationsofthesesurfacesgenerallyrequireaprofessionalandarenot"do-it-yourself'projects.
Reviewsurfacespecificationsbeforepurchasingthistypeofsurfacing.Asktheinstaller/manufacturerforareportshowingthattheproducthas
beentestedtothefollowingsafetystandard:ASTMF1292StandardSpecificationforImpactAttenuationofSurfacingMaterialswithintheUse
ZoneofPlaygroundEquipment.Thisreportshouldshowthespecificheightforwhichthesurfaceisintendedtoprotectagainstseriousheadinjury.
Thisheightshouldbeequaltoorgreaterthanthefallheight-verticaldistancebetweenadesignatedplaysurface(elevatedsurfaceforstanding,
sitting,orclimbing)andtheprotectivesurfacingbelow-ofyourplayequipment.
Checktheprotectivesurfacingfrequentlyforwear.
Placement
Properplacementandmaintenanceofprotectivesurfacingisessential.Besureto
Extendsurfacingatleast6feetfromtheequipmentinalldirections.
Forto-froswings,extendprotectivesurfacinginfrontofandbehindtheswingtoadistanceequaltotwicetheheightofthetopbarfromwhichthe
swingissuspended.
Fortireswings,extendsurfacinginacirclewhoseradiusisequaltotheheightofthesuspendingchainorrope,plus6feetinalldirections.
2H 2H
H
L
6 ft.
6 ft.
6 ft. 6 ft.
L+6 ft.
6 ft.
6 ft.
Use Zone for Single-Axis Swings Use Zone for Multi-Axis Swings
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
9 This information has been extracted from the CPSC publications "Playground Surfacing-Technical Information Guide" and "Handbook for Public
Playground Safety"Copies of these reports can be obtained by sending a postcard to the: Office of Public Affairs, U.S. Consumer Product Safety
Commission, Washington, D.C., 20207 or call the toll-free hotline: [phone]

5
6’ -0’’
14’ -8’’
11’ -0’’
28’ -0’’
26’ -8’
6’ -0’’
6’ -0’’
6’ -0’’
14’ -0’’
14’ -0’’
83’’ TO
SWING HANGER
PIVOT
8’’ MINIMUM
9’ -6’’
DIMENSIONS
MINIMUM USE ZONE FOR PLAY EQUIPMENT SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE PLAY
STRUCTURE.
SWING USE ZONE EXTENDS NO LESS THAN 168”.
SWINGS MUST HAVE A MINIMUM CLEARANCE OF 8” ABOVE THE PROTECTIVE SURFACING.
6’ -0’’
20’ -2’’
11’ -0’’
28’ -0’’
32’ -2’’
6’ -0’’
6’ -0’’
6’ -0’’
14’ -0’’
14’ -0’’
83’’ TO
SWING HANGER
PIVOT
8’’ MINIMUM
9’ -6’’

6
TOOLS REQUIRED
DRILL 1/2” & 7/16’’ SOCKETS &
WRENCH
HAMMER ADJUSTABLE
WRENCH
TAPE MEASURE
PHILLIPS BIT CARPENTER
SQUARE
SAFETY GLASSES 1/8” DRILL BIT
SCREWDRIVER
INCLUDED HARDWARE
5/16” Washer (x39)
5/16” Loc Nut (x10)
#12 x 3/4” Pan Screw (x6)
3/16” Tarp Washer (x6)
5/16’’ Loc Washer (x18)
5/16-18 T-Nut (x18)
Small
5/16” Wood Loc
Washer (x3)
2-1/2” Deck Screw (x170)
2” Deck Screw (x105)
1-3/4” Deck Screw (x155)
3” Deck Screw (x9)
1-5/8” Deck Screw (x12)
1-1/4” Deck Screw (x16)
3/4” Flat Head Screw (x18 )
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
#14 x 1-3/4” Truss Screw (x6)
Square Bit (x1)
30mm Deck Screw (x320)
1-3/16’’
PLIERS
1/4” x 1-3/4” Pan Screw (x2)
1/4” Washer (x18)
1/4’’ Loc Washer (x16)

7
HARDWARE
5/16”-18 x 8-1/2” Hex Bolt (x1) 5/16”-18 x 7” Hex Bolt (x1)
5/16”-18 x 6” Carriage Bolt (x3)
5/16”-18 x 4” Hex Bolt (x7) 5/16”-18 x 3-1/2” Hex Bolt (x4) 5/16”-18 x 3-1/4” Hex Bolt (x2) 5/16”-18 x 2-1/2” Hex Bolt (x4)
5/16”-18 x 1-3/4” Hex Bolt (x1)
5/16”-18 x 2” Hex Bolt (x2)
8-1/2’’
7’’
6’’
4’’
3 1/2’’
3 1/4’’
2 1/2’’
2’’
8-1/2’’ 7’’ 6’’
4’’ 3 1/2’’ 3 1/4’’
2 1/2’’
5/16” x 1-1/2” Lag Screw (x4) Steering Wheel Spacer (x1)
5/16”-18 x 3” Carriage Bolt (x1)
8-1/2’’ 7’’ 6’’
4’’ 3 1/2’’ 3 1/4’’
2 1/2’’
1/4”-20 x 1-1/4” Hex Bolt (x12)
1/4 -18 T-Nut (x12)
Small

8
(1) [PF 6298] 2-11/16” x 3” x 62’’ SWING BEAM SUPPORT
(2) [PF 6325] 3’’ x 3’’ x 94-1/4’’
(2) [PF 6324] 3’’ x 3’’ x 94-1/4’’
(1) [PF 6323] 3’’ x 3’’ x 31-1/2’’ TOWER BEAM SUPPORT
(2) [PF 6315] 1’
’ x 3-3/8’’ x 53’’
(2) [PF 6300] 3/4’’ x 3-3/8’’ x 15-3/4’’
(2) [PF 6319] 5/8’’ x 2’’ x 28’’
(1) [PF 6331] 5/8’’ x 3-3/8’’ x 31-1/2’’
(1) [PF 6322] 1’’ x 5-3/8’’ x 28-1/2’’
(1) [PF 6311] 3/4’’ x 5-3/8’’ x 21-1/2’’
(1) [PF 6314] 1’’ x 3-3/8’’ x 31-1/2’’
(2) [PF 6303] 5/8’’ x 3-3/8’’ x 30’’
(1) [PF 6302] 3/4’’ x 3-3/8’’ x 9-3/4’’
(1) [PF 6310] 5/8’’ x 3-3/8’’ x 8-5/16”
(1) [PF 6309] 5/8’’ x 3-3/8’’ x 35’’
(1) [PF 6340] 5/8” x 5-3/8” x 26-7/8”
(6) [PF 6341] 5/8” x 5-3/8” x 26-7/8”
(1) [PF 6299] 2-5/8” x 5-3/8” x 93” SWING BEAM
(2) [PF 6317] 5/8’’ x 1-3/8’’ x 12’’
(1) [PF 6339] 5/8’’ x 5-3/8’’ x 31-1/2’’
(1) [PF 6338] 3/4’’ x 3-3/8’’ x 31-1/2’
’
(1) [PF 6346] 5/8’’ x 3-3/8’’ x 31-1/2’’
SA6066 BOX 1 of 2
BOARD LIST

9
SA6065 BOX 2 of 2
BOARD LIST
(2) [PF 6297] 1-3/8’’ x 3-3/8’’ x 83’’ A-FRAME
(1) [PF 6296] 1-3/8’’ x 3-3/8’’ x 58’’ A-FRAME SUPPORT
(2) [PF 6352] 1-3/8’’ x 3-3/8’’ x 31-1/2’’
(2) [PF 6295] 1-3/8’’ x 3-3/8’’ x 17-1/4’’ SLIDE STAKE
(2) [PF 6334] 1-3/8’’ x 3-3/8’’ x 8’’
(1) [PF 6326] 1’’ x 3-3/8’’ x 42’’
(2) [PF 6313] 1-3/8’’ x 3’’ x 77-1/4’’
(1) [PF 6314] 1’’ x 3-3/8’’ x 31-1/2’’
(2) [PF 6351] 1’’ x 3-3/8’’ x 29-1/8’’
(2) [PF 6350] 1’’ x 3-3/8’’ x 26’’
(2) [PF 6329] 1’’ x 3-1/4’’ x 4-5/8’’
(3) [PF 6335] 3/4’’ x 3-3/8’’ x 62-1/2’’
(1) [PF 6336] 3/4’’ x 3-3/8’’ x 51-3/4’’
(1) [PF 6337] 3/4’’ x 3-3/8’’ x 51-1/4’’
(1) [PF 6338] 3/4’’ x 3-3/8’’ x 31-1/2’’
(1) [PF 6316] 3/4’’ x 3-3/8’’ x 24’’
(2) [PF 6333] 3/4’’ x 3-3/8’’ x 15-1/2’’
(2) [PF 6332] 3/4’’ x 3-3/8’’ x 13’’
(1) [PF 6302] 3/4’’ x 3-3/8’’ x 9-3/4’’
(2) [PF 6312] 1-3/8’’ x 1-3/8’’ x 31-1/2”
(2) [PF 6355] 1-3/8’’ x 1-3/8’’ x 27-3/4’’
(4) [PF 6318] 5/8’’ x 1-3/8’’ x 8’’
(2) [PF 6354] 5/8’’ x 3-3/8’’ x 37-3/8’’
(3) [PF 6309] 5/8’’ x 3-3/8’’ x 35’’
(4) [PF 6308] 5/8’’ x 3-3/8’’ x 35’’
(2) [PF 6320] 5/8’’ x 3-3/8’’ x 34-3/4’’
(1) [PF 6345] 5/8’’ x 3-3/8’’ x 34’’
(8) [PF 6347] 5/8’’ x 3-3/8’’ x 31-1/2’’
(1) [PF 6346] 5/8’’ x 3-3/8’’ x 31-1/2’’
(1) [PF 6331] 5/8’’ x 3-3/8’’ x 31-1/2’’
(2) [PF 6307] 5/8’’ x 3-3/8’’ x 31-1/2’’
(7) [PF 6306] 5/8’’ x 3-3/8’’ x 31-3/8’’
(7) [PF 6348] 5/8’’ x 3-3/8’’ x 30-7/8’’
(6) [PF 6303] 5/8’’ x 3-3/8’’ x 30’’
(2) [PF 6349] 5/8’’ x 3-3/8’’ x 29-1/2’’
(2) [PF 6328] 5/8’’ x 3-3/8’’ x 28-1/2’’
(6) [PF 6327] 5/8’’ x 3-3/8’’ x 23’’
(5) [PF 6304] 5/8’’ x 3-3/8’’ x 17’’
(1) [PF 6310] 5/8’’ x 3-3/8’’ x 8-5/16”
(1) [PF 6342] 5/8’’ x 3-3/8’’ x 7’’
(2) [PF 6343] 5/8’’ x 3-3/8’’ x 6-3/8’’
(2) [PF 6321] 5/8’’ x 3-3/8’’ x 6-3/4’’ SUNBURST
(1) [PF 6344] 5/8’’ x 3-3/8’’ x 5-3/8’’
(1) [PF 6353] 5/8’’ x 3-3/8’’ x 3’’
(2) [PF 6301] 3/4’’ x 3-3/8’’ x 26-7/8’’
(20) [PF 6330] 1/2” x 3-5/16” x 36-3/4” SHINGLE
(2) [PF 6305] 5/8’’ x 3-3/8’’ x 25-3/8’’

10
Swing Seat (x2)
3/8’’ x 5-1/2’’ 2631
Bag of (x6) Swing Hangers
Window Pane (x1)
COMPONENTS
Swing Beam Bracket (x2) Beam Brace (x1)
Tarp (x1)
Play Handle (x2)
Steering Wheel (x1)
Standing Swing (x1)

11
Anchor It Strap (x4) Anchor It (x4)
Climbing Rock (x6)
ID Tag (x1)
ASSEMBLY INSTRUCTIONS
Email us at: [email protected] or call us at 1-800-844-9273
Printed in USA
Customer Service
1-800-844-9273
1000 Ternes Drive
Monroe, MI 48162
16644PLAY
A Backyard Products Company
Model: 4276
4369
6007
6192
IMPORTANT!!
PLEASE READ BEFORE BEGINNING ASSEMBLY!!
Please make sure all lumber, hardware and accessory parts are accounted for.
If you are missing anything, please DO NOT RETURN to the store where purchased.
Please call our Customer Service Department at the number below.
LDR 01-29-2018
Plan (x1)
Flag Assembly (x2) Telescope (x1)
Coolwave Slide (x1)
COMPONENTS
Warning Plate (x1)

STEP 1
12
30mm Deck Screw (x42)
Check to make sure
structure is square
!
Install 30mm Screws
With Heads Flushed To
Board To Avoid
Protrusions.
1. Assemble Panel A, Panel B an Panel C as shown.
2. Mark panels A, B and C.
PANEL C
1-3/16’’
PANEL A
PANEL B
PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’
PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’
(4) PF 6309 5/8’’ x 3-3/8’’ x 35’’
35-5/8’’
(4)
30mm Deck Screws
Per Board
5-3/8’’
8-3/8’’ 8-3/8’
5/8’’
Flush
PF 6335 3/4’’ x 3-3/8’’ x 62-1/2’’
4-7/16’’
PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’
(5) PF 6304 5/8’’ x 3-3/8’’ x 17’’
5/8’’
(4)
30mm Deck Screws
Per Board
NOTE HOLES
1’’
18-5/8’’
1-7/16’’
SPACE
2-3/8’’
SPACE
18-11/16’’
16-516’’
5-7/16’’
(4) PF 6308 5/8’’ x 3-3/8’’ x 35’’
2-3/8’’
35-5/8’’
5/8’’
Flush
PF 6354 5/8’’ x 3-3/8’’ x 37-3/8’’
PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’
SPACE

13
STEP 2
Check to make sure
structure is square
FRAME A
2-1/2” Deck Screw (x12)
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
1. Assemble Frame A as shown.
Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
PF 6338 3/4’’ x 3-3/8’’ x 31-1/2’’
Flush
Flush
Flush
Flush
PF 6324 3’’ x 3’’ x 94-1/4’’
PF 6325 3’’ x 3’’ x 94-1/4’’
(2)
2-1/2’’ Deck Screws
(2)
2-1/2’’ Deck Screws
(2)
2-1/2’’ Deck Screws
NOTE:
HOLE
ORIENTATION
PANEL A
(2)
2-1/2’’ Deck Screws
(2)
2-1/2’’ Deck Screws
T-Nut
Small
T-Nut
Small
31-1/2’’
18-11/16’’ TO HOLES
(2)
2-1/2’’ Deck Screws
Flush

14
STEP 3
2-1/2” Deck Screw (x4)
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
PF 6314 1’’ x 3-3/8’’ x 31-1/2’’
5/16-18 X 4’’
Hex Head Bolt
5/16’’Loc-Washer
5/16’’ Washer
(2)
2-1/2’’ Screws
1. Flip frame over and Attach Frame Support Board as shown.
FLIP FRAME
OVER
FRAME A

15
STEP 4
PF 6335
3/4’’ x 3-3/8’’ x 62-1/2’’
Flush
(1) PF 6347 5/8’’ x 3-3/8’’ x 31-1/2’’
PF 6324 3’’ x 3’’ x 94-1/4’’
PF 6325 3’’ x 3’’ x 94-1/4’’
(2) PF 6310 5/8’’ x 3-3/8’’ x 8-5/16’’
PF 6307 5/8’’ x 3-3/8’’ x 31-1/2’’
(2)
2-1/2’’ Deck Screws
(2)
2-1/2’’ Deck Screws
per Board
This Side
(2)
2-1/2’’ Deck Screws
per Board
This Side
(2)
2-1/2’’ Deck Screws
1. Assemble Frame B as shown.
Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
2. Install Window Pane as shown.
FRAME B
2-1/2” Deck Screw (x20)
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
3/4” Flat Head Screw (x10 )
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
WINDOW PANE INSTALL
(10)
3/4’’ Flat HeadScrews
NOTE:
HOLE
ORIENTATION
(2)
2-1/2’’ Deck Screws
(2)
2-1/2’’ Deck Screws
PF 6307 5/8’’ x 3-3/8’’ x 31-1/2’’
T-Nut
Small
T-Nut
Small
Check to make sure
structure is square
31-1/2’’
3-1/2’’
NOTE HOLES

16
STEP 5
2-1/2” Deck Screw (x4)
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
PF 6314 1’’ x 3-3/8’’ x 31-1/2’’
1. Flip frame over and Attach Frame Support Board as shown above.
FLIP FRAME
OVER
FRAME B
5/16-18 X 4’’
Hex Head Bolt
5/16’’Loc-Washer
5/16’’ Washer
(2)
2-1/2’’ Screws

17
STEP 6
2-1/2” Deck Screw (x14)
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
1. Attach frame Support Boards and Panel A to Frame A as shown above.
FRAME A
PF 6336 3/4’’ x 3-3/8’’ x 51-3/4’’
(2)
2-1/2’’ Screws
(3)
2-1/2’’ Screws
PF 6337 3/4’’ x 3-3/8’’ x 51-1/4’’
PF 6354 5/8’’ x 3-3/8’’ x 37-3/8’’
PF 6339 3/4’’ x 5-3/8’’ x 31-1/2’’
3’’
From Outside
of Post
Flush
(3)
2-1/2’’ Screws
Flush
PANEL C
(2)
2-1/2’’ Screws
94-1/4’’
(2)
2-1/2’’ Screws
(2)
2-1/2’’ Screws
Check to make sure
structure is square
20-1/4’’
Flush
NOTE HOLE
LOCATION
PF 6337
Flush to
outside edge
of 3”x 3”
Flush
PANEL A
Flush to
outside edge
of 3”x 3”
Side View of Tower
3’’ From
outside of post
To end of horizontal
support.

18
STEP 7
2-1/2” Deck Screw (x14)
FS2828
1-3/4
FS2826
1-1/4
FS2827
1-5/8
FS2829
2
FS2830
2-1/2
FS2831
3
FS2826
3/4
1. Attach Frame B to Frame A as shown.
(2)
2-1/2’’ Screws
FRAME A FRAME B
(2)
2-1/2’’ Screws
(3)
2-1/2’’ Screws
(5)
2-1/2’’ Screws (2)
2-1/2’’ Screws
Flush
Flush 3’’ From Outside
of Post
From Outside
of Post
Side View of Tower
3’’ From
Outside of Post
to End of Horizontal
Support.
19-1/2’’