BALAY 3VF302NA - annexe 1 User manual

Dishwasher summary of instructions
Brief and handy: everything
your dishwasher needs ...
Before using for the first
time, read the operating
instructions!
Switch off the appliance Everythingo.k. ...
9000 397 759    
en
Start programme Here we go ...
Adding rinse aid
Adding detergent
Select programme
Filling the salt dispenser
Switching on the appliance
Adjusting the water softening system * Quickly sorted ...
Ask your water supply
company what the water
hardness is and enter ...
* only before the first wash
or if the water hardness
has been changed
How to adjust the water softening system
–Switch on ON/OFF switch.
–Hold down button > and press Start button until and “End” flash.
–Release buttons.
The display flashes and the displays are lit (= setting 1).
Change the setting as follows:
–Button < press until the required setting has been selected.
–Press Start button.
The and “End” displays go out. The selected setting is saved.
–Close the door.
Read off the correct setting for your water hardness
Setting°Clarke mmol/l
27–44
0–8
9–20
21–26
0
1
2
3
0–1,1
1,2–2,9
3,0–3,7
3,8–6,2
Hardness
range
soft
medium
hard
hard
A B C A
< >
Dissolves limescale (not necessary for set value 0!) ...
Unscrew
cover. Fill the salt
dispenser with
water before the
first wash only.
Add salt
(never add
detergent!).
Screw on the
cover. Wash
immediately.
Spick and span ... Refill if rinse-aid refill indicator is lit!
Press mark 1,
lift up cover 2. Adding rinse aid.Screw on the cover.
CLICK!
A lot of dirt, a lot of detergent ...
If required, open
the cover (press
button).
Attention
Combination
products are not
suitable for all
programmes, follow
manufacturer’s
instructions.
Adding
detergent.Slide cover shut, press.
PLOP!
Quick, economical or intensive ...
The max. possible number of programmes is illustrated
in this overview. The corresponding programmes for your
appliance can be found on the fascia.
Overview of programmes
The programme data has been measured in the laboratory
according to European standard EN 50242.
Deviations are possible in practice.
* half normal load
2:15
1,50
15
2:20
1,05
12
1:10
0,80
13
0:29*
0,80
10
0:15
0,05
4
2:10
1,45
14
Quick
45_
Eco
50_
Intensive
70_
Normal
65_
Gentle
40_
Duration: hs/mins
Energy Consumption: kWh
Water consumption in litres
Prerinse
Additional options ** Flexibility...
Express Wash
(VarioSpeed)
... is obtained by
increased energy
consumption at a
constant cleaning and
drying performance.
Half load
... for a few items, saves
water, energy and time
** depending on model
IntensiveZone
... perfect for a mixed
load. Washing pressure
and washing
temperature are
increased slightly.
Hygiene
... The temperature is
increased during
the rinsing process. This
increases the hygiene
status.
Extra drying
... improves the drying
result by increased
temperature in the final
rinse (Please take care
with delicate dishes)

Maintenance and care For perfect rinsing results ... Cleaning waste water pump
Filters ...
check, if
required clean
Rotate filter
cylinder, remove
filter system ...
rinse under
running water ... insert ... Screw on filter system NOTE
MARK!
–Pull out the mains plug
–Remove filters and scoop out water
–Lever off cover (––>A)
–Check area around the fan impeller
for foreign objects
–Click cover shut (––>B)
–Insert filters
Spray arms ...
Remove
blockages/deposits
pull lower arm
upwards ... unscrew upper arm ... clean spray nozzles under running water
(if required use
toothpicks) ...
insert lower arm ...
screw on upper arm
tightly
A B
Rectifying minor faults yourself ... ... as it is worth doing it yourself!
Fault Possible causes
Display “ ” display is lit Supply fitting jammed or calcified. Open supply fitting.
Remedial action
Waste water pump blocked. Clean waste-water pump (see above).
Rust on the cutlery Cutlery not rust-resistant. Hard knife blades are more susceptible. Use dishwasher–proof cutlery.
Display ” ” flashes
Residual water in the
appliance
Appliance has technical defect.
Waste water hose is blocked or kinked.
Call factory customer service.
Install waste water hose without kinks.
The programme has not yet ended. Close and switch on the appliance
or terminate the programme
(see Terminating the programme).
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10 l/min. when
water supply is open.
If the flow rate is less, replace the
supply fitting.
Install supply hose without kinks.
Attach cover (see above).
Unplug appliance.
Cover not attached to waste water
pump.
Extraneous rust Never wash rusting parts in the
appliance.
Fault Possible causes Remedial action
Stains and streaks
Milky deposits on the
utensils (can be removed)
Rinse-aid dosage too high/too low.
Glasses not dishwasher–proof.
Streaks: reduce dosage.
Use dishwasher–proof glasses.
More information can be found in the operating instructions
Milky deposits, glasses
cloudy/tarnished (cannot be
removed)
Water softening system incorrectly set. Correctly set water softening system.
Utensils are not clean Utensils are situated close together or
one above the other.Separate the utensils, prevent contact points.
Plastic/utensils discoloured Too little detergent. Follow manufacturer’s instructions
(detergent).
Sand or gritty residue on the
utensils Too little detergent.
Unsuitable programme selected.
Spray arm nozzles blocked.
Filters dirty, not seated firmly.
Spray arms blocked.
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the filters (see above).
Clean the spray arms (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Water or limescale stains: increase
dosage.
Refill with salt.
No salt.
Use a detergent suitable for glasses.
Discoloration caused by food colourings
(tomato sauce). Discoloration is harmless; subsequent rinse cycles will cause it to fade.
Terminating the programme ... Loading the dishwasher correctly ...
Whilethe programme is running,
press the START button for
approx. 3 sec. (Reset). Switching off the appliance
1 minute after the
programme has
ended, the “pro-
gramme end” dis-
play illuminates.
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove
large remnants of jam, milk products and food according to the operating instructions and check that the
spray arms can rotate freely.