Brandt BDJ424DB User manual

Dishwasher
BDJ424DB

If you cannotsolve the problemsby yourself,
please ask for help from a professional technician.
To review

1

2

3
tableware with sharp points

4

Press the program button for more than 3 seconds to cancel the running program.
Refer to the section entitled "Preparing and loading dishes".
Close the door, press the program button until the selected program lights up.
(see the section entitled "Operation instruction")
When the working cycle has finished, then stop. Turn off the appliance using On/Off button.
Scrap off any large amount of leftover food.
Soften remnants of burned food in pans, then load the baskets.
Refer to the dishwasher loading instruction.
5
(Follow the user instructions!)
Open the flap(marked with A), fill in the main wash detergent , and then close the flap;
Pre wash detergent drop into the tank directly;
Refill the rinse aid through the hole below the cap(marked with B)
If you need .
A
B

Control Panel
before using it for the first time.
To get the best performance from your dishwasher, read all operating instructions
IMPORTANT
9.On/Off Button: To turn on/off the power supply.
7. Program Button :Press the button to select a
wash Program.
5.Salt and rinse aid warning lights: To show
when the salt container or dispenser need to be
refilled
6.Program indicators: To show which program
has been chosen.
8.Power indicator: To show when the power is on.
2.Display Window: To show the delay time,
etc.
functions.
error codes .
6
To be selected only with 6 place-setting dishware or less.
This option will enable the lowering of water and energy
consumptions. Use this function only with intensive,Eco,
1 hour and glass programs.
3. Operating instructions
1.Delay Button :Press thebutton to delaycycle start time.
3.Half-load Button: To select Half load
is selected.
4.Half-load indicator:Goes on when half-load function
• Manual pre-rinsing of tableware items leads to increased water and energy consumption and is not recommended
• Washing tableware in a household dishwasher usually consumes less energy and water in the use phase than hand
dishwashing when the household dishwasher is used according to the manufacturer’s instructions.

The water softener must be set manually, using the water hardness dial.
The water softener is designedto remove mineralsand salts fromthe water,which would have
a detrimental or adverse effect on the operation of the appliance.
The higher thecontent of these minerals and salts, the harder your water is.
The softener shouldbe adjusted accordingto the hardnessof the waterin your area.Yourlocal WaterAuthority
can advise you on the hardness of the water in your area.
Adjusting Salt Consumption
the water used.This is intended to optimiseand customise thelevel o fsalt consumption.
1. Open the door ,Switch on the appliance;
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will
form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt container specifically designed to eliminate
lime and minerals from the water.
Contact your local water board for information on the hardness of your water supply.
H1
H2
H3
H4
Please follow the steps below for adjustment in salt consumption.
A. Water SoftenerA. Water Softener
NOTE:NOTE:
If your model does not have any water softener, you may skip this section.
H5
H6
Note:2Note:2
The manufactory setting: H3 (EN 50242)
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kgdishwasher salt andthen fill the salt container to the top with water
C. Fill the rinse aid dispenser
D. Fill in detergent
¡ã
Clark: British degree
¡ã
fH: French degree
¡ã
dH: German degree
Note:1Note:1 dH=1.25 Clarke=1.78 fH=0.178mmol/l
¡ã ¡ã ¡ã
1
dH
mmol/l
0~90~5 0~0.94 0
10-20
6-11 1.0-2.0 9
21-30
12-17 2.1-3.0 12
20
fH
0~6
7-14
15-21
Clarke
WATER HARDNESS
Selector Position Salt consumption
(gram/cycle)
18-22 31-40 22-28 3.1-4.0
41-60
23-34 4.1-6.0 30
60
29-42
35-55 61-98 43-69 6.1-9.8
7
The dishwasher is designed to adjust the amount of salt consumed based on the hardness of
2. Press theProgram button formore than 5seconds to start the water softener
setting mode within 60seconds after the appliance was switched on( The Salt and
Rinse aid warninglightswill be onperiodically when it gets in thesetting mode );
3. Press theProgram button toselect the propersetting according toyour local environment,
the settings will change in the following sequence: H3->H4->H5->H6->H1->H2->H3;
4. Press the Power button to end the setting mode.

Depending on howwell the saltdissolves, the saltwarning light maystill be oneven though the
salt container isfilled.
If there isno salt warninglight in thecontrol panel (forsome Models),you canestimate when tofill
the salt intothe softener bythe cycles thatthe dishwasher hasrun.
2. If thereare spills ofthe salt, asoak or arapid program shouldbe run toremove the excessivesalt.
Always use the salt intended for use with dishwasher.
The salt container is located beneath the lower basket and should be filled as explained
in the following:
Attention!
Only use salt specifically designed for the use in dishwashers! Every other type of
salt not specifically designed for the use in a dishwasher, especially table salt, will
damage the water softener. Incase of damages caused by the use of unsuitable
salt the manufacturer does not give any warranty nor is liable for any damages caused.
Only fill with salt just before starting one of the complete washing programs.
This will prevent any grains of salt or salty water, which may have been spilled,
remaining on the bottom of the machine for any period of time, which may cause
corrosion.
B. Loading the Salt Into the SoftenerB. Loading the Salt Into the Softener
NOTE:NOTE:
Full fill the salt container with water,It is normal for a small amount of water to come out of the
salt container.
11
22
A After the lower basket has been removed, unscrew and remove the cap from the salt container.
BPlace the end of the funnel (supplied) into the hole and introduce about 1.5kg of dishwasher salt.
C
D After filling the container , screw the cap tightly back clockwise.
E The salt warning light will stop being after the salt container has been filled with salt.
FImmediately after filling the salt into the salt container, a washing program should be started (We suggest to use a short
program). Otherwise the filter system, pump or other important parts of the machine may be damaged
by salty water. This is out of warranty.
1122
OpenOpen
8
1. The salt container mustonly be refilledwhen the saltwarning light inthe control panel goes on.