Ballard Designs Del Ray JM119 User manual

B E F ORE YOU STA R T
Unpack and lay all Ping Pong Table pieces
flat on a padded surface to avoid scratching
or damaging the components.
Look for anengraved letter near each slot on
the enclosed riserpieces. Always match up
coordinating slots (A+A, B+B,etc.) to ensure
properassembly.
Locate and count all hardware before
discarding any packaging.
I M POR TANTN OT E
The Ping Pong Table is designed for
on-deck use only.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Page 1 of 4
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 4-26-2022
MADE IN USA
PRODUCT NAME: Del Ray Ping Pong Table
ITEM NUMBER: JM119
ASSEMBLED DIMENSIONS : 30”H x 48”W x 96”L

NET (1)
STORAGE DRAWER (2)PADDLE(2)
STORAGE DRAWER KEY (2)
KEY (20)
BOTTOM CROSSBAR (2)
TOP CROSSBAR MIDDLE (2)
TOP CROSSBAR END (2)
LONG CROSSBAR (2)
BALLS (4)
CONTENTS
TABLE TOP (1)
TABLELEG (2)
BRACKET (2) SHELF (2)
SCREWS (23)ALLEN WRENCH (1)
STEP 1:Align the corresponding slots of thebottom
crossbars and thetablelegs. Make sure theletter
system is facing theinside of thetable. Slide the
pieces together, using amallet if needed. Continue
until all fourpieces are assembled together.
STEP 2: Align the corresponding letters of the shelves
and drop them on the L-slot tabs. Slideinward until it
locks into place, using amallet if needed.
A
B
E
F
I
JK
L
E
F
A
B
I
JK
L
C
STEP 3: Alignthe corresponding letters of the two
brackets and insert them into the table legs. Slide the
pieces together, using a mallet if needed.
E
F
I
JK
L
F
G
Page 2 of 4

STEP 4:Alignthe corresponding letters of the
top crossbars and insert them into thetablelegs.
Slidethepieces together, using a mallet if needed.
Continue until you have inserted all four crossbars
(two middle crossbars,two end crossbars) into the
tablelegs and the tops are flush.
STEP 5:Alignthe corresponding letters of the long
crossbarand insert thepiece into the table frame.
Slidethepieces together, using a mallet if needed.
Continue until the top of thelong crossbar is flush
with the rest of the frame.
STEP 6:Insert the (20) keys into the key slots located
on the brackets. Do not screw the keys into place
until step 8.
F
L
R
M
F
I
JK
K
N
LL
R
M
R
Q
K
K
STEP 7: Place the table top on top of the frame.
Adjust slightly until the grooves on the bottom of the
table align and thetable rests properly on the
table frame.
STEP 8:Locate the (20) keys you have already
inserted into thetableand screw them into place
using theincluded Allen screws and Allen wrench.
FFL
L
E
A
B
E
STEP 9:Slidethe paddle/ball drawers into place.
Page 3 of 4

STEP 10: Secure the drawers withthe T-shaped keys
and screws.
STEP 11:Slidethe side of thenet with ahook tab into
thenotch of the table top. Push down onthe other
side to lock into place.
STEP 12:Optionally, secure the net to the table top
witha screw.
STEP 13: You’re all done! Enjoy your new product and
begin creating life’s most meaningful moments. Tag
us for a chance to be featured!
CARE AND MAINTENA NCE
ROUTINE CLEANING
Clean with a soft cloth,microfiber towel, orspray
down with a water hose. For adeeper clean, use mild
soap and water with asoft bristlebrush.
POWER WASHING
Use caution to avoid inscribing your ping pong table.
Start with a very low PSI at least 3 feet away from
furniture, and test ontheunder sidebefore moving
closer. Move closerorincreasePSI gradually and with
caution until dirt is removed. Check often to ensure
no inscriptionis left onfurniture.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Page 4 of 4