For
The
Installer
FITTING
INTO
THE
WORKTOP
All our cooking hobs are designed
to
be
fitted into worktops, whether made
of
wood or laminated plastic, provided
it
is
a
heat resistant surface.
For
building in,
it
is
sufficient
to
make a hole in
the
worktop
as
shown opposite (560mm x 490mm) keeping
a minimum distance
of
40mm-50mm from the rear wall
to
avoid
damage by heat.
If
a horizontal partition
is
fitted underneath
the hob,
it
should
be
located at a minimum
distance
of
90mm from the
top
of
the
work
surface.
The
minimum recommended
height
for
a cooker hood above
an
electric hob
is
650mm.
The
minimum height
of
adjacent units should
be
366mm above
work
surface.
The
minimum height
of
cabinets
above hob,
if
not
fitting
hood,
is
900mm.
NEVER
FIT
HOBS
ABOVE
REFRIGERATION
PRODUCTS.
The
appliance
has
been tested according
to
heat protection
of
the mounting surface
as
class
'Y',
EN
60335-2-6.
If there
is
a false floor under the hob,
it
has
to
be
removable
for
installation purposes.
Insert the hob into the worktop opening from above. Make sure that the hob
connection cable
is
directed
to
the
rear.
Positioning
ofTensioning
Brackets
Using 4 brackets, tension hob against the
worktop
in
such
a way
that
the entire
seal
fits tightly
to
the worktop.
The
hob
has
4 tensioning brackets
with
fastening claws.
For
their positions
see
fiyure
opposite:
WARNING: For safety purposes,
the
supplied
tensioning
brackets
must
be used.
Do
not
use
the hob before
it
has
been built in.
To
ensure water tightness between the casing and the
worktop, glue the foam
seal
to
the edge
of
the casing
surround.
Connection
To
Mains
Your hob must
be
installed by a competent person
in
line
with
all electrical and
installation requirements published by the Institute
of
Electrical Engineers.
We
recommend that the appliance
is
connected by a qualified electrician, who
is
a
member
of
the N.I.C.E.I.C and
who
will comply
with
the
I.E.
E.
and local regulations.
The
following cable types
can
be used
for
connecting
to
the mains:
Cable
type
Connection
type
AC230 V
(single phase)
H 05
RR
F3G
2.5
(3
x 2.5mm2) or
H 05
VV
F3G
2.5
(3
x 2.5mm2)
The
line marked green and yellow
(PE)
is
to
be
connected
to
the terminal showing the
protective conductor symbol
~!
For
230/240 volt
use,
connections
to
the input terminal block
(located in the connection box underneath
th
top
right hand
corner
of
the hob) are
as
follows:
Ensure
the supplied link
is
correctly inserted between
the
L1 and
L2
terminals.
~
__
--•••¥N
0
0
This
appliance must be permanently wired using suitable cable
to
the fixed wiring
of
the house
via
an
all-pole isolator
with
a minimum contact gap
of
3mm (e.g. line safety
switch, circuit-breaker, contractor).
Depending on the power and type
of
connection,
the
appliance
has
to
be
fuse-
protected by the installation
of
the house
as
follows:
Connection
type
AC
230 V
Power
as
per
nameplate
5.5-7.0
kW
Fuse
1 X
25
A
If
the
supply
to
the appliance
is
provided
with
a superposed residual-current-operated
breaker, this breaker
has
to
be sensitive
to
pulsed currents.
The
protection against accidental contact
with
the mains
is
only effective after
the
appliance
has
been completely built in.
-
Ra~ing
Plate
'
--
The
rating plate,
with
all
the
important data and information about your appliance, will
not
be
accessible after building in, therefore we have enclosed a second nameplate,
which
is
self-adhesive.
Please
stick this onto the installation instructions
to
make
it
available whenever you
need
the appliance data.
