Baoding Longer Precision Pump Longer BT300-1F User manual

BT300-1F Longer Peristaltic Pump
TM
Bao ing L Precision Pump Co.,Ltd.d onger
BaodingLongerPrecisionPumpCo.,Ltd
ADD: Building A,Chuangye Center Baoding
National High - Tech Industrial Development Zone
Baoding,Hebei,China 071051
TEL: 86 - 312 - 3110087 3138553
FAX: 86 - 312 - 3168553
E - mail: [e-mail]
Http:www.longerpump.com
BT300-1F PERISTALTIC PUMP
OPERATING MANUAL

BT300-1F OPERATING MANUAL
Introduction
Operation Panel
Basic Operation
Running Interface
Menu Frame Work
Function Setting
Start/Stop Key
Direction Key
Adjusting Knob
Prime Key
Exit Key
Filling and Dispensing Setting
Calibration Function
System Setting
Tubing I.D.
Remote Control
Pump I.D.
Footswitch
Back Suction
Time Setting
Pump Head Selection
Control Mode
Acceptable Pump Heads and Tubing
Pump Head Mounting
Remote Control
Optional Accessories
Communication Function
Maintenance
Warranty
Technical Specifications
TableofContents
1
2
2
2
2
2
2
3
4
4
5
7
8
9
10
10
2
11
11
12
12
13
14
15
15
18
18
18
18
19
IMPORTANT INFORMATION：
Please read operation manual carefully before operation.
WARNINGS：
Tubing breakage may result in fluid being sprayed from
pump. Use appropriate measures to protect operator and
equipment. Please check the tubing frequently and
changethetubingintime.
If the power line or the plug is worn or damaged please
pull out the plug (Hold the plug not the power line when
pulling out).
Please shut down the power supply and pull out the plug
when meet below circumstances (Hold the plug not the
power line when pulling out).
Thefluidssplashonthebodyofthepump.
Youthinkthepumpneedstobemaintainedorrepaired.
Please shut down the power supply before install the
external control equipments.

BT300-1F OPERATING MANUAL
Introduction
Operation Panel
Basic Operation
Running Interface
Menu Frame Work
Function Setting
Start/Stop Key
Direction Key
Adjusting Knob
Prime Key
Exit Key
Filling and Dispensing Setting
Calibration Function
System Setting
Tubing I.D.
Remote Control
Pump I.D.
Footswitch
Back Suction
Time Setting
Pump Head Selection
Control Mode
Acceptable Pump Heads and Tubing
Pump Head Mounting
Remote Control
Optional Accessories
Communication Function
Maintenance
Warranty
Technical Specifications
TableofContents
1
2
2
2
2
2
2
3
4
4
5
7
8
9
10
10
2
11
11
12
12
13
14
15
15
18
18
18
18
19
IMPORTANT INFORMATION：
Please read operation manual carefully before operation.
WARNINGS：
Tubing breakage may result in fluid being sprayed from
pump. Use appropriate measures to protect operator and
equipment. Please check the tubing frequently and
changethetubingintime.
If the power line or the plug is worn or damaged please
pull out the plug (Hold the plug not the power line when
pulling out).
Please shut down the power supply and pull out the plug
when meet below circumstances (Hold the plug not the
power line when pulling out).
Thefluidssplashonthebodyofthepump.
Youthinkthepumpneedstobemaintainedorrepaired.
Please shut down the power supply before install the
external control equipments.

1 2
S1
S2
P1 P3
P4
P2
Introduction
BT300-1F peristaltic pump is a multi-function peristaltic pump
developed by our company. It can connect many pump heads. The
flow rates are 0.005 - 1140 mL/min. 128 x 64 graphic LCD displays
running menus and parameter setting menus. The display interfaces
are friendly. It has many control modes. The external control can be
realized through standard external interface or 485 communication
interface.
S Standard Configuration
S1 Pump Head
S2 Drive
PParts
P1 Build-in fuse
P2 Power Socket
P3 Remote Control Output Interface
P4 Remotel Control Input Interface
OP Optional Fittings
OP1 External Control Module
Reference:
For detail information about remote control function please see
page 15.
Operation Panel
Exit Key
Power Switch
Adjusting Knob
Start/Stop Key
Direction Key
Prime Key
Basic Operation
Start/Stop Key
Pressthe tostartorstopthepump.
Direction Key
Press the to change the rotation direction of the
pump.
Adjusting Knob
Function 1: Adjust the flow rates or speed in running state.
Function 2: In menus selection state, press the
for confirmation and turn the for selecting and
setting the menus.
Prime Key
In common state, press the to enter prime state when
the pump runs at full speed for empting, filling and rinsing
operation; Press the again to return to common state.
In prime state, other keys (except )are invalid.
Exit Key
Cancel current operation and return to previous menu.
Start/Stop Key
direction key
Adjusting Knob
Adjusting Knob
Prime Key
Prime Key
Direction Key
BT300-1F OPERATING MANUAL BT300-1F OPERATING MANUAL

1 2
S1
S2
P1 P3
P4
P2
Introduction
BT300-1F peristaltic pump is a multi-function peristaltic pump
developed by our company. It can connect many pump heads. The
flow rates are 0.005 - 1140 mL/min. 128 x 64 graphic LCD displays
running menus and parameter setting menus. The display interfaces
are friendly. It has many control modes. The external control can be
realized through standard external interface or 485 communication
interface.
S Standard Configuration
S1 Pump Head
S2 Drive
PParts
P1 Build-in fuse
P2 Power Socket
P3 Remote Control Output Interface
P4 Remotel Control Input Interface
OP Optional Fittings
OP1 External Control Module
Reference:
For detail information about remote control function please see
page 15.
Operation Panel
Exit Key
Power Switch
Adjusting Knob
Start/Stop Key
Direction Key
Prime Key
Basic Operation
Start/Stop Key
Pressthe tostartorstopthepump.
Direction Key
Press the to change the rotation direction of the
pump.
Adjusting Knob
Function 1: Adjust the flow rates or speed in running state.
Function 2: In menus selection state, press the
for confirmation and turn the for selecting and
setting the menus.
Prime Key
In common state, press the to enter prime state when
the pump runs at full speed for empting, filling and rinsing
operation; Press the again to return to common state.
In prime state, other keys (except )are invalid.
Exit Key
Cancel current operation and return to previous menu.
Start/Stop Key
direction key
Adjusting Knob
Adjusting Knob
Prime Key
Prime Key
Direction Key
BT300-1F OPERATING MANUAL BT300-1F OPERATING MANUAL

Running Interface
Switch on the power switch, initialize the pump first and then display
the running interface.
rpm State
b.
c.
d.
f.
e.
Flow Rates State
a.
b.
c.
d.
g.
e.
a.
h.
i.
a.
Filling and Dispensing State
3 4
20:47:49
300 RPM
ID3.1
INT
1.800mL/min
20:47:49
ID3.1
INT
Clock：20：47：49
Copy No.： 2
Disp Vol： 0.1mL
Menu Frame Work
20:47:49
1.800mL/min
ID3.1
INT
1.
Fill Setting
2.
Calibration
3.
System Setting
4.
Control Mode
1.1.
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
2.1.
Act Vol： 31mL
Disp Time： 27"
Press to begin
3.1.
TubingI.D.：ID2.4
3.2.
Remote Control：
On
3.3.
Pump I.D. ：1
3.4.
Footswitch：
Trigger
3.5.
Back Suction：
18°
3.6.
Clock Setting：
3.7.
Pump Head：
DG(6-roller)
4.1.
Select
RPM Flow Disp
Function Setting
↑
20:47:49
1.800mL/min
ID3.1
INT
1. 2.
3.
4.
a. :Currenttime.Setinsystemsettingmenu.
b. Direction: Show the direction of the pump.
c. Tubing ID: Display the current tubing inner diameter.
d. Start/Stop state: “Start” state displays “ ”, “Stop” state displays“ ”.
e. Control Mode: “shut” means remote control is in “off” state. Remote
control is in “on” state, “INT” means the pump are controlled by
internal control; “V” means the pump are controlled by remote control
analog voltage signal; “mA” means the pump are controlled by remote
control analog current signal.
f. rpm: Display current speed. Turning the can increase
or decrease the speed.
g. Flow Rate: Display current flow rate. Turning the can
increase or decrease the flow rate.
h. Copy No.: Display copy number in dispensing and filling state.
i. : Display filling volume (one time) in dispensing and filling
state.
Adjusting Knob
Adjusting Knob
Clock
Disp Vol
BT300-1F OPERATING MANUAL BT300-1F OPERATING MANUAL
Running Interface
Running Interface
Fill Setting Calibration
Prompt:
Exit Key
The symbol of “ “ in the
interface means you can
press the to
return to the previous
interface.
In “Running Interface”, press the to enter “Fill
Setting” interface. Turn the to select 4 kinds of
Function Setting Interface.
Adjusting Knob
Adjusting Knob
Press the
Knob
Turn the
Knob
Turn the
Knob
Turn the
Knob
System Setting
Control Mode

Running Interface
Switch on the power switch, initialize the pump first and then display
the running interface.
rpm State
b.
c.
d.
f.
e.
Flow Rates State
a.
b.
c.
d.
g.
e.
a.
h.
i.
a.
Filling and Dispensing State
3 4
20:47:49
300 RPM
ID3.1
INT
1.800mL/min
20:47:49
ID3.1
INT
Clock：20：47：49
Copy No.： 2
Disp Vol： 0.1mL
Menu Frame Work
20:47:49
1.800mL/min
ID3.1
INT
1.
Fill Setting
2.
Calibration
3.
System Setting
4.
Control Mode
1.1.
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
2.1.
Act Vol： 31mL
Disp Time： 27"
Press to begin
3.1.
TubingI.D.：ID2.4
3.2.
Remote Control：
On
3.3.
Pump I.D. ：1
3.4.
Footswitch：
Trigger
3.5.
Back Suction：
18°
3.6.
Clock Setting：
3.7.
Pump Head：
DG(6-roller)
4.1.
Select
RPM Flow Disp
Function Setting
↑
20:47:49
1.800mL/min
ID3.1
INT
1. 2.
3.
4.
a. :Currenttime.Setinsystemsettingmenu.
b. Direction: Show the direction of the pump.
c. Tubing ID: Display the current tubing inner diameter.
d. Start/Stop state: “Start” state displays “ ”, “Stop” state displays“ ”.
e. Control Mode: “shut” means remote control is in “off” state. Remote
control is in “on” state, “INT” means the pump are controlled by
internal control; “V” means the pump are controlled by remote control
analog voltage signal; “mA” means the pump are controlled by remote
control analog current signal.
f. rpm: Display current speed. Turning the can increase
or decrease the speed.
g. Flow Rate: Display current flow rate. Turning the can
increase or decrease the flow rate.
h. Copy No.: Display copy number in dispensing and filling state.
i. : Display filling volume (one time) in dispensing and filling
state.
Adjusting Knob
Adjusting Knob
Clock
Disp Vol
BT300-1F OPERATING MANUAL BT300-1F OPERATING MANUAL
Running Interface
Running Interface
Fill Setting Calibration
Prompt:
Exit Key
The symbol of “ “ in the
interface means you can
press the to
return to the previous
interface.
In “Running Interface”, press the to enter “Fill
Setting” interface. Turn the to select 4 kinds of
Function Setting Interface.
Adjusting Knob
Adjusting Knob
Press the
Knob
Turn the
Knob
Turn the
Knob
Turn the
Knob
System Setting
Control Mode

1.1.
Set Disp Vol：
1.0 mL
Enter “Fill Setting” interface:
1. Other parameters can't be set here. Set the other parameters
first and then go along the “Fill Setting”. Other parameters
setting methods please see page 8 “System Setting”.
2. In “Running Interface” press the to enter “Fill
Setting” interface. Press the again to enter
filling setting menu. Turn the Adjusting Knob to select
parameters. There are 4 parameters. They are Volume, Pause
time, Copy No., Flow.
Adjusting Knob
Adjusting Knob
1.
1.4.
Flow：
7.705mL/min
Time：13.23"
1.1.
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
20:47:49
1.800mL/min
ID3.1
INT
↑
1.2.
1.3.
1. 1.1.
20:47:49
ID3.1
INT
↑
1.800mL/min
1.2.
Set Pause Time：
2"
1. 1.1.
20:47:49
ID3.1
INT
↑
1.800mL/min
1. 1.1.
20:47:49
ID3.1
INT
1.800mL/min
1.3.
：Copy No.
5
1.2.
↑
1.3.
6
5
Running Interface
Running Interface
Running Interface
Running Interface
BT300-1F OPERATING MANUAL BT300-1F OPERATING MANUAL
Fill Setting
Fill Setting
Fill Setting
Fill Setting
Turn the
Knob
Turn the
Knob
Turn the
Knob
Turn the
Knob
Turn the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Filling and Dispensing Setting
Please make sure the pump is in
“Flow” or “Disp.” state. See page 13
“Control Mode” for setting method.
Please make sure the pump is in
“Flow” or “Disp.” state. See page 13
“Control Mode” for setting method.
Please make sure the pump
is in “Flow” or “Disp.” state.
See page 13 “Control Mode”
for setting method.
Please make sure the pump
is in “Flow” or “Disp.” state.
See page 13 “Control Mode”
for setting method.
Volume: In “Fill Setting” interface, press the to
enter the next interface. Press the to enter
“Volume” interface. Turn the to input required
volume. Press the to confirm, save and quit.
Press the to cancel the setting and return to the previous
interface.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Pause Time: The pause time between two filling. Its range is 1s -
999s. In “Fill Setting” interface, press the to
enter the next interface. Turn the to highlight the
“Pause time”. Press the to enter “Pause time”
interface. Turn the to adjust the pause time.
Press the to confirm, save and quit. Press the
to cancel the setting and return to the previous interface.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Copy No.: the total filling number. Its range is 1- 999.
In “Fill Setting” interface, press the to enter the
next interface. Turn the to highlight the “Copy
No.”. Press the to enter “Copy No.” interface. Turn
the to adjust the copy number. Press the
to confirm, save and quit. Press the to
cancel the setting and return to the previous interface.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob Exit Key
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Turn the Knob
to adjust volume
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Turn the Knob
to adjust Pause Time
Turn the Knob
to adjust copy no.
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：

1.1.
Set Disp Vol：
1.0 mL
Enter “Fill Setting” interface:
1. Other parameters can't be set here. Set the other parameters
first and then go along the “Fill Setting”. Other parameters
setting methods please see page 8 “System Setting”.
2. In “Running Interface” press the to enter “Fill
Setting” interface. Press the again to enter
filling setting menu. Turn the Adjusting Knob to select
parameters. There are 4 parameters. They are Volume, Pause
time, Copy No., Flow.
Adjusting Knob
Adjusting Knob
1.
1.4.
Flow：
7.705mL/min
Time：13.23"
1.1.
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
20:47:49
1.800mL/min
ID3.1
INT
↑
1.2.
1.3.
1. 1.1.
20:47:49
ID3.1
INT
↑
1.800mL/min
1.2.
Set Pause Time：
2"
1. 1.1.
20:47:49
ID3.1
INT
↑
1.800mL/min
1. 1.1.
20:47:49
ID3.1
INT
1.800mL/min
1.3.
：Copy No.
5
1.2.
↑
1.3.
6
5
Running Interface
Running Interface
Running Interface
Running Interface
BT300-1F OPERATING MANUAL BT300-1F OPERATING MANUAL
Fill Setting
Fill Setting
Fill Setting
Fill Setting
Turn the
Knob
Turn the
Knob
Turn the
Knob
Turn the
Knob
Turn the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Filling and Dispensing Setting
Please make sure the pump is in
“Flow” or “Disp.” state. See page 13
“Control Mode” for setting method.
Please make sure the pump is in
“Flow” or “Disp.” state. See page 13
“Control Mode” for setting method.
Please make sure the pump
is in “Flow” or “Disp.” state.
See page 13 “Control Mode”
for setting method.
Please make sure the pump
is in “Flow” or “Disp.” state.
See page 13 “Control Mode”
for setting method.
Volume: In “Fill Setting” interface, press the to
enter the next interface. Press the to enter
“Volume” interface. Turn the to input required
volume. Press the to confirm, save and quit.
Press the to cancel the setting and return to the previous
interface.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Pause Time: The pause time between two filling. Its range is 1s -
999s. In “Fill Setting” interface, press the to
enter the next interface. Turn the to highlight the
“Pause time”. Press the to enter “Pause time”
interface. Turn the to adjust the pause time.
Press the to confirm, save and quit. Press the
to cancel the setting and return to the previous interface.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Copy No.: the total filling number. Its range is 1- 999.
In “Fill Setting” interface, press the to enter the
next interface. Turn the to highlight the “Copy
No.”. Press the to enter “Copy No.” interface. Turn
the to adjust the copy number. Press the
to confirm, save and quit. Press the to
cancel the setting and return to the previous interface.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob Exit Key
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Turn the Knob
to adjust volume
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Turn the Knob
to adjust Pause Time
Turn the Knob
to adjust copy no.
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：

1.4.
Flow：
7.705mL/min
Time：13.23"
Note:
Change the tubing if can't get the desired filling time.
1. 1.1.
20:47:49
ID3.1
INT
↑
1.800mL/min
1.4.
：Flow
7.705mL/min
Time：13.23"
1.
20:47:49
ID3.1
INT
1.800mL/min
2.
1.
20:47:49
ID3.1
INT
1.800mL/min
2.
2.1.
Set Test Time:
27"
Press to next
2.1. 2.1.
Cal Vol： 30mL
Press to begin
↑
Prompt:
In “Disp.” state, the testing time of flow rate calibration can be set the
time of disp. Time (please see the “Flow” setting of “Filling setting”) for
more accurate filling volume.
Enter “System Setting” interface.
There are 7 submenus in “System Setting” menu. They are “Tubing
ID”, “Remote Control”, “Pump I.D.”, “Footswitch”, “Back Suction”,
“Clock Setting” and “Pump Head”.
78
Running Interface
Running Interface
Running Interface
BT300-1F OPERATING MANUAL BT300-1F OPERATING MANUAL
Fill Setting
Fill Setting
Fill Setting
Calibration
Calibration
System Setting
Turn the
Knob
Turn the
Knob
Turn the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Press the
Knob
Please make sure the pump
is in “Flow” or “Disp.” state.
See page 13 “Control Mode”
for setting method.
Please make sure the pump
is in “Flow” or “Disp.” state.
See page 13 “Control Mode”
for setting method.
Please make sure the pump
is in “Flow” or “Disp.” state.
See page 13 “Control Mode”
for setting method.
Disp Vol 1.6mL
ause Time 2"
Copy No. 4
：
P：
：
Flow: Adjust the dispensing and filling efficiency. Its range is
determinedbythepumpheadandtubing.
In “Fill Setting” interface, press the to enter the
next interface. Turn the to highlight the “Flow”.
Press the to enter “Flow” interface. Turn the
to adjust the flow rate and dispensing time.
Press the to confirm, save and quit. Press the
to cancel the setting and return to the previous
interface.
: Filling time for one time.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Adjusting Knob
Exit Key
Time
Calibration Function
Calibration is needed in below situation:
1. Use the pump the first time; 2. Change the pump head; 3.
Change the tubing; 4. Setting the new flow rate; 5. Operating
condition changes.
Enter calibration function setting interface:
In “Running Interface”, press the to enter “Fill
Setting” interface, turn the to enter
“Calibration” interface.
Adjusting Knob
Adjusting Knob
Flow Rate Calibration
In “Calibration” interface, press the to enter “Test
Time” setting interface. Turn the to set the test
time. Its range is 1s 999s. Press the to enter the
next interface. Press the to begin the testing.
Turn the to input the actual volume after testing.
Press the to confirm, save and quit. Press the
to cancel the calibration and return to the “Calibration”
interface.
Adjusting Knob
Adjusting Knob
Adjusting Knob
Start/Stop Key
Adjusting Knob
Adjusting Knob
Exit Key
Act Vol： 31mL
Disp Time： 27"
Press to begin
Press
Turn the Knob to adjust
flow rate and disp. time
Turn knob to
input actual the volume
Turn knob to set
test time