Bar-B-Chef KYS-367S User manual
INSTRUCTION MANUAL
Bar-B-Chef
Electric
BBQ
Code No:
BB
Q
E
Model No:KYS-367S
Read
these
instructions
thoroughly
before
first
use
Before use
P
l
ea
s
e
rea
d
t
h
e
s
e
i
ns
t
r
u
c
t
i
o
ns
carefully
.
T
h
ey
w
i
ll
g
i
v
e
y
o
u
i
m
p
o
r
t
a
n
t
a
d
v
i
c
e
f
o
r
t
h
e
us
e
,
s
e
c
u
r
i
t
y
a
n
d
ma
i
n
t
e
n
a
n
c
e
o
f
t
h
is
a
pp
l
i
a
n
c
e
.
K
ee
p
t
h
ese
i
ns
t
r
u
c
t
i
o
ns
a
n
d
,
sh
o
u
l
d
t
h
e
s
i
t
u
a
t
i
o
n
ar
i
s
e
,
p
a
ss
t
h
em
o
n
to
other
us
er
s
.
T
h
e
a
pp
l
i
a
n
c
e
m
us
t
o
n
l
y
be
us
e
d
f
o
r
t
h
e
i
n
t
e
n
d
e
d
pu
r
p
o
s
e
a
cc
o
r
d
i
n
g
to
t
h
e
s
e
i
ns
t
r
u
c
t
i
o
ns
.
O
b
s
er
v
e
any local regulations
.
Dispose of
t
h
e
p
a
c
k
ag
i
n
g
thoughtfully.
Safety regulations
Plug the appliance only in conventional 240V AC domestic outlets as mentioned on the
rating plate and only into regular earthed, three-pin sockets.
An electric appliance is not a children’s toy. Children are not aware of the hazards of electrical
appliances. Therefore close supervision is necessary when the appliance is used by children. Do
not allow power cable to hang down within easy reach. Keep children away from packing material,
e.g. plastic bags.
The installation of a faulty current protective device with a rated breaking current offers you
additional safety by ensuring that 30 mA will not be exceeded in the house installation. Get more
advice on this from your electrician. Danger also exists with appliances which have
been switched off, so after use, the plug should always be removed for the mains.
Do not use this appliance within reach of water contained in bath-tubs, washbasins or other
Receptacles. Never expose it to rain, snow or other moisture.
Regularly check whether the power cord is defective. In this case the appliance must not be put
into operation (immediately disconnect the plug). Consult your store of purchase for advice.
The appliance must not be operated (disconnect the mains plug immediately) when:
the appliance, casing or power cord is damaged
the appliance shows visible signs of damage.
a fault is suspected after the appliance has been dropped or similar
Switch off all the power point and disconnect the main plug:
in case of faults during use.
before cleaning or moving the appliance from place to place.
after use
Never pull the plug out of the socket by the power cord or with wet hands.
Never carry nor pull the appliance by the power cord.
Don’t pull the power cord over sharp edges. Don’t wedge (eg under doors etc.).
Never immerse the power cord or the thermostat plug in water or any other liquid
.
Only use extension leads after having made sure that their condition is faultless and use an
earthed cable with a minimum capacity of 10A.
Positon the power cord and cable so that unintentional touching or catching is impossible.
Never allow the extension lead or power cord to be in touch with the hot grill plate.
Always switch off the appliance before removing the mains plug.
Before removing attachments or cleaning the appliance, allow it to cool completely
.
Take care! The hotplate will get very hot, and it stays hot for a long time after it has been
switched off. Beware of burns! Do not touch any hot surfaces and take care when handling the
appliance after use.
Do not stand the bbq over the edge or corner of a table and avoid all contact with the bbq hot
surfaces.
Do not place the appliance on or near a hot gas electrical burner, or in a heated oven.
Only use the appliance when it is placed on a stable and dry surface
Do not leave the appliance unattended
Always switch off and disconnect the appliance from power when it is not in use.
This appliance is not meant for commercial use but exclusively for private use
.
Do not use the appliance without the grease cup and the bbq base all fitted properly together.
Never cover the hotplate with aluminum foil or trays (this might damage the non-stick coating)
Make sure without fail that this appliance is installed correctly before first use.
Beware of fat oil or moisture spitting while grilling
.
Place the appliance on a surface that is resistant to heat. Keep the electric grill at least 30 cm
from any walls when in operation
Use this appliance only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock or injury to persons possibly resulting in depth or
permanent disablement.
For safety reasons do not use attachments that were not recommended or supplied by the
manufacturer.
Only trained personnel should repair electrical appliances. Unskilled repairs can cause
considerable danger to the user.
If the power cord is damaged, it must be replaced only by the manufacturer, their after-sales
service department or a similarly qualified person in order to avoid risks.
No
warranty
for
any
possible
damage
can
be
accepted
if
the
appliance
is
used
for
improper
purpose,
wrongly
operated
or
unprofessionally
repaired.
In
such
a
case,
any
warranty
claim
is
void.
Electric diagram
Data plate
Description
1
Roasting
h
oo
d
2
H
oo
d handle
3
Hotplate
4
Grease
c
up
5
B
a
s
e
6
S
t
a
n
d
t
u
be
7
U
pp
er
tube
8
Tool holder
9
Base tube
10
Condiment
ba
s
k
e
t
11
B
a
s
e handle
12 Opening for appliance socket
13 Detachable temperature
Regulator with cable
14 Temperature indicator lamp
15
Power inlet
s
o
c
k
et
1 6
Feet
1 7 Axle
1 8 Wheel
1 9 Hubcaps
2 0 M4×6 screws
2 1 ”R” Pins
2 2 M6×30 screws +M6 nuts
2 3 Bracket
2 4 M6 ×30 screws +M6 nuts
2 5 M6×30 screws +M6 nuts
2 6 Butterfly screw
2 7 M5x18 Screw
Installation instructions
A. Fit
the
feet
(16)
to
the
base
tube
( 9 )
.Fix
in
place
with
two
M4*6
screws
（
20
）
.
Left
and
right
side
are
the
same
B.Put the axle (17) through the two holes
In the base tube as shown.Attach the wheels (18)
to the axle
.
C.
Insert the “R” pin (21) through the holes in the ends
of the axle to lock the wheels
Press the hubcaps (19) onto the wheels.
D
．
Insert the upper tube (7) to the base tube (9)
Insert the M6 ×30 screws (22) from the outside
through the holes in the two tubes. Then
Tighten up with the nuts and washers provided.
E. Install the bracket (23) onto the upper tube (7)
with M 6 × 30 screws（24）and nuts (24).
Install the stand tube (6) onto the brackets(23).
Note the slot on the stand tube which is going to fix the
bbq base. Fix the stand tube in place with two screws
（25）and nuts.
F
．
Join the two parts (10A) and (10B) as shown.
Hang to the outside of set screws (22)
Place the tool holder (8) on the upper tube as shown
G
Set the bbq base (5) into the stand tube (6)
By aligning the base with the slot and pushing the
bbq all the way down. When removing the bbq base
step softly on the base tube (9) hold the handles of
the bbq base and lift it off
H
Put the grease cup (4) into the bracket provided for it
in the back of the bbq base. Push the grease cup into
the correct position in the middle of the bowl-shaped
base. (Tip: The grease cup can be filled with a little
water to Make it easier to clean). It’s recommended
to install a butterfly screw (26) to lock the base to the
trolley.
I
．
Place the hotplate (3) in the bbq (5).
Insert the power inlet socket (15) of the hotplate
into the opening for the powercord with the hotplate
tilted upwards ，Then lower the hotplate onto bbq
base. Before taking the hotplate out , make sure it is cool
and disconnected from the power.
Attention
:
The
hotplate
must
only
be
used
TOGETHER
with
BBQ bowl
!
J
．
Use a M5 × 18 screw (27) through the inside of the hood
with silicone washer and lid hook (26) into the hood handle
Tighten the hood clockwise to fix the handle.
While assembling, keep the hood handle and hook aligned
K
．
Insert the temperature regulator with cable(13) into
the power inlet socket. Plug in the appliance
When inserting or removing the power cord hold the
handle of the bbq base to avoid pushing over the
appliance.
Attention:
Please
take
care.
Avoid
tripping
over
by
the
power
cord
when
operating
the
appliance
Arrange
the
power
cord
so
its
out
of
your
way.
Remember
to
remove
the
plug
after
use.
L.
The roasting hood can act as a wind shield
by clipping the hook onto the hotplate
Before using the appliance for the first time
Remove all the packaging materials and wash the hotplate (3), grease cup (4) and roasting hood (1)
thoroughly
Important:
Dry all the different parts thoroughly. This applies especially to the power inlet socket
(15) .Never immerse the power cord with regulator (13) in water.
Heat the grill to its maximum setting for about 3-5 minutes, with the roasting hood in place and
without any food. Residues left from manufacturing may cause some smell and smoke when the
appliance is used for the first time
.
Cooking
instructions
Connect the appliance to the mains electricity supply.
Set the temperature regulator (13) to the required temperature level (it usually takes about 3
minutes to preheat). Pre heating is faster with the roasting hood in place.
The temperature indicator lamp (14) will go out as soon as the required temperature has been
reached.
Place the food to be grilled on the hotplate (3)
Cooking times
The following are recommended cooking times. Different times will be required for different
weights and sizes of foods to be grilled, and depending on whether you are grilling with or without
the roasting hood. Weather conditions can also affect cooking times.
Food to be grilled Temperature grade setting Cooking time
Steak/beef 5 15-20 mins
Lamb 5 12-18 mins
Chicken drumsticks 5 25-30 mins
Chops 5 20-25 mins
Chicken wings 5 15-20 mins
Fillet of pork 4-5 9-10 mins
Whole fish 5 12-15 mins
Kebabs 3-4 10-12 mins
Various sausages 3-4 12-15 mins
Tips for grilling
Your meat will be more if you marinade in the refrigerator it overnight before cooking (you can
make your own marinade from oil (to aid moistness), vinegar, fruit juice or wine (to tenderise)
and a mixture of seasonings for flavour).
Always use tongs to turn grilled food (using a fork to turn the food will dry it out and damage
the non-stick coating). Take care with tongs not to damage the non-stick coating.
Only turn meat and fish once during grilling. You do not need to turn it more than once and too
much turning dries food out.
Never cook meat for too long. Even pork is better if it is served when it is still a little pink and
juicy.
If cooked food sticks to the hotplate, rub the plate with a piece of kitchen paper soaked in oil
from time to time.
Cleaning and looking after the appliance
Disconnect the appliance from the mains electricity supply
.
Allow the grill to cool completely.
Take the power cord with regulator (13) out of the appliance socket.
Clean
the
hotplate
(3)
and
grease
cup
bowl
(4)
with
warm
washing-up
water
and
a
damp
cloth.
Do
not
use
steel
wool
pads,
brush
or
abrasives
to
avoid
any
damages
to
the
coating
of
Wipe the base of the appliance (5) with a damp cloth. Fat splashes can be removed with a mild
hotplate.
cleaning agent.
Note:
The
hotplate
has
a
non-stick
coating.
Do
not
scratch
this
coating
during
either
the
cooking
or
the
cleaning
stages.
Tip:
Protect the appliance from dust and dirt if it is not to be used for a prolonged length of time (dry
thoroughly then wrap it in a plastic bag). Store it in a cool dry place.
Disposal
Disable unserviceable appliances immediately. Remove the mains plug and cut up the mains
connection cable. If possible, bring unserviceable appliances to an official waste collection point.
Many local authorities provide removal services for bulky refuse at least once a year.
Please see separate sheet for warranty details
For service and warranty repairs please contact your place of purchase ,
BRANCHES AUSTRALIA WIDE
Call 1 300 301 392 for your nearest store
Barbeques Galore Limited,
Build A2, Campus Business Park, 350-374 Parramatta Road, Homebush, NSW 2140
Email : CSR1@bbqgalore.com.au
Table of contents
