Barco MCM-50 User manual

MCM-50
User Guide
Optimized for F50
R5909057/02
17/05/2016

Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Printed in Belgium

Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site
https://www.barco.com/en/signin.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
EN55022/CISPR22 Class A ITE (Information Technology Equipment)
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such equipment should not
be restricted in its sale but the following warning shall be included in the instructions for use:
Warning : This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interfer-
ence.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in
the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures
which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal
maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the
customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
eCos
The software in this product uses eCos, the Embedded Configurable Operating System.

This is the license for eCos:
Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003 Red Hat, Inc.
Copyright (C) 2002, 2003 John Dallaway
Copyright (C) 2002, 2003 Nick Garnett
Copyright (C) 2002, 2003 Jonathan Larmour
Copyright (C) 2002, 2003 Andrew Lunn
Copyright (C) 2002, 2003 Gary Thomas
Copyright (C) 2002, 2003 Bart Veer
eCos is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free
Software Foundation; either version 2 or (at your option) any later version.
eCos is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABIL-
ITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with eCos; if not, write to the Free Software Foundation, Inc.,
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
As a special exception, if other files instantiate templates or use macros or inline functions from this file, or you compile this file and link it
with other works to produce a work based on this file, this file does not by itself cause the resulting work to be covered by the GNU General
Public License. However the source code for this file must still be made available in accordance with section (3) of the GNU General Public
License.
This exception does not invalidate any other reasons why a work based on this file might be covered by the GNU General Public License.
The eCos source used to build the software used in the Barco iCon is available on request from Barco.

Table of contents
TABLE OF CONTENTS
1. Safety instructions................................................................................................. 5
1.1 Notice on safety ...................................................................................................................... 5
1.2 Installation instructions ............................................................................................................... 5
1.3 Owner’s record ....................................................................................................................... 5
1.4 Warnings.............................................................................................................................. 6
1.5 Plug types............................................................................................................................. 6
1.6 Heat and fire hazard.................................................................................................................. 7
1.7 Installation ............................................................................................................................ 7
1.8 Prevent personal injury ............................................................................................................... 7
1.9 Device damage....................................................................................................................... 7
1.10 Environment condition check......................................................................................................... 8
1.11 Service................................................................................................................................ 8
1.12 Cleaning .............................................................................................................................. 9
1.13 Repacking . . . ......................................................................................................................... 9
2. Introduction ........................................................................................................11
2.1 About this manual . . ................................................................................................................. 11
2.2 Symbols and fonts . . .................................................................................................................12
2.3 Key features and benefits ...........................................................................................................12
3. Packaging...........................................................................................................13
3.1 Content...............................................................................................................................13
3.2 Unpacking . . . ........................................................................................................................14
4. Facility and system requirements..............................................................................17
4.1 Environmental requirements ........................................................................................................17
4.2 Installation requirements . . . .........................................................................................................17
5. Physical installation and connections.........................................................................19
5.1 RCU battery installation .............................................................................................................19
5.2 Installing the rack mount plate ......................................................................................................20
5.3 DisplayPort connection ..............................................................................................................21
5.4 Connecting the F50 projector .......................................................................................................21
5.5 Power connection . . .................................................................................................................22
5.6 Network connection .................................................................................................................23
6. Setup and configuration .........................................................................................25
6.1 Setting the RCU address . . . .........................................................................................................25
6.2 Powering the MCM-50...............................................................................................................27
6.3 Activating the MCM-50 ..............................................................................................................27
6.4 Setting the MCM-50 address........................................................................................................28
6.5 Network configuration ...............................................................................................................29
6.5.1 Configuring the MCM-50 for a Private Subnet . . ............................................................................30
6.5.2 Configuring the MCM-50 for a DHCP network...............................................................................31
6.6 Linking MCM-50 devices in a multi-channel system ...............................................................................32
7. Getting started.....................................................................................................37
7.1 Starting the MCM-50 ................................................................................................................37
7.2 Displaying a single source ..........................................................................................................37
7.3 Displaying multiple sources: Stitched Layouts .....................................................................................37
7.3.1 Details on Stitched Layouts...................................................................................................39
7.3.2 Creating a Window file........................................................................................................39
7.3.3 Viewing Window file information..............................................................................................42
7.3.4 Editing a Window file..........................................................................................................43
7.3.4.1 Locking to the sync of another source.................................................................................43
7.3.4.2 Editing Stitch Layout ...................................................................................................43
7.3.4.3 Input Stereo Sync settings . . . . . ........................................................................................44
7.3.5 Saving a Window file..........................................................................................................45
7.3.6 Loading a Window file ........................................................................................................45
7.3.7 Renaming a Window file......................................................................................................46
7.3.8 Copying a Window file ........................................................................................................47
7.3.9 Deleting a Window file ........................................................................................................47
7.4 Basic image adjustment.............................................................................................................48
7.4.1 Adjusting the brightness ......................................................................................................48
7.4.2 Adjusting the contrast.........................................................................................................49
7.4.3 Adjusting the gamma .........................................................................................................50
8. OSD Preferences ..................................................................................................51
8.1 Displaying the advanced menu items...............................................................................................51
8.2 Navigating through the OSD ........................................................................................................52
8.3 Opening a drop down menu.........................................................................................................52
8.4 Opening a dialog box................................................................................................................52
8.5 Activating a menu item of a drop down menu ......................................................................................52
R5909057 MCM-50 17/05/2016 1

Table of contents
8.6 Moving a slider in a slider box.......................................................................................................53
8.7 Entering data in an edit box.........................................................................................................53
9. Basic operation....................................................................................................55
9.1 General settings .....................................................................................................................55
9.1.1 Identification...................................................................................................................55
9.1.2 Freeze.........................................................................................................................55
9.1.3 Automatic startup .............................................................................................................56
9.1.4 Change password.............................................................................................................56
9.2 Source alignment: timings . .........................................................................................................57
9.2.1 Loading a Custom Image file .................................................................................................58
9.2.2 Editing a Custom Image file ..................................................................................................58
9.2.3 Saving a Custom Image file ..................................................................................................61
9.2.4 Renaming a Custom Image file...............................................................................................61
9.2.5 Copying a Custom Image file.................................................................................................62
9.2.6 Deleting a Custom Image file.................................................................................................63
9.3 Colors: using Dynacolor............................................................................................................. 63
10. Advanced operation ..............................................................................................65
10.1 Geometry adjustment................................................................................................................65
10.1.1 Geometry adjustment principle ...............................................................................................65
10.1.2 Keystone correction workflow ................................................................................................68
10.1.3 General geometry adjustment workflow......................................................................................68
10.1.4 The Geometry edit dialog.....................................................................................................68
10.1.5 Selecting the geometry level .................................................................................................70
10.1.6 Selecting an anchor point.....................................................................................................71
10.1.7 Moving an anchor point in small steps .......................................................................................72
10.1.8 Moving an anchor point in large steps .......................................................................................73
10.1.9 Geometry reset................................................................................................................74
10.2 Using Dynacolor sets................................................................................................................76
11. Expert operation...................................................................................................77
11.1 Geometry ............................................................................................................................ 77
11.1.1 Setting the Axis link to ON or OFF ...........................................................................................77
11.1.2 Working with Geometry files..................................................................................................79
11.1.2.1 Loading a Geometry file................................................................................................80
11.1.2.2 Renaming a Geometry file .............................................................................................81
11.1.2.3 Copying a Geometry file ...............................................................................................81
11.1.2.4 Deleting a Geometry file ...............................................................................................82
11.1.3 Shifting the image on the projector panel ....................................................................................83
11.1.4 Transport delay ...............................................................................................................85
11.2 Soft Edge and Black Level ..........................................................................................................86
11.2.1 Soft Edge and Black Level explained ........................................................................................86
11.2.2 Soft Edge area shape.........................................................................................................88
11.2.3 General Soft Edge workflow..................................................................................................91
11.2.4 Alpha planes . .................................................................................................................94
11.2.5 Beta planes ...................................................................................................................95
11.2.6 The Soft Edge selection dialog...............................................................................................96
11.2.7 The Soft Edge edit dialog.....................................................................................................98
11.2.8 Selecting an anchor point....................................................................................................100
11.2.9 Moving an anchor point in small steps ......................................................................................100
11.2.10 Moving an anchor point in large steps ......................................................................................101
11.3 Dynacolor...........................................................................................................................101
11.3.1 Dynacolor concept and expert use..........................................................................................102
11.3.2 The Dynacolor dialog ........................................................................................................106
11.3.3 Enabling Dynacolor......................................................................................................... .107
11.3.4 Color fine tuning..............................................................................................................108
11.3.5 Color calibration..............................................................................................................110
11.3.6 Dynacolor for Infitec..........................................................................................................112
12. Maintenance...................................................................................................... 115
12.1 Maintenance: general overview. . . .................................................................................................115
12.2 Cleaning housing and mechanical structure.......................................................................................115
12.3 Firmware upgrade . .................................................................................................................115
12.4 Diagnostics through the OSD ......................................................................................................116
12.4.1 I2C............................................................................................................................117
12.4.2 Board identification ..........................................................................................................117
12.5 Diagnostic LEDs ....................................................................................................................118
12.6 Identification ........................................................................................................................119
12.7 Internal and scaled patterns........................................................................................................119
12.8 Troubleshooting checklist . . ........................................................................................................121
13. MCM-50 Tools .................................................................................................... 123
13.1 High Bandwidth Digital Protection .................................................................................................123
13.2 EDID ................................................................................................................................124
13.2.1 Selecting an EDID file .......................................................................................................124
13.2.2 Creating Custom EDID files .................................................................................................125
2R5909057 MCM-50 17/05/2016

Table of contents
13.2.3 Deleting Custom EDID files..................................................................................................127
13.3 Patterns.............................................................................................................................127
13.4 Textboxes ...........................................................................................................................127
13.5 Menu bar position ..................................................................................................................128
13.6 Status bar position..................................................................................................................128
13.7 Positioning the slider box...........................................................................................................129
13.8 Sync Variance Limit ................................................................................................................129
13.9 Full-screen synchronous representation. . . . .......................................................................................131
14. Specifications.................................................................................................... 133
14.1 General specifications..............................................................................................................133
14.2 Dimensions .........................................................................................................................134
14.3 Technical Regulations ..............................................................................................................134
15. RCU Control...................................................................................................... 135
15.1 Range of RCU and IR receivers . . .................................................................................................135
15.2 OSD navigation and selection......................................................................................................136
15.3 Data input ...........................................................................................................................137
15.4 MCM-50 control.....................................................................................................................138
16. Environmental information .................................................................................... 141
16.1 Disposal information................................................................................................................141
16.2 Rohs compliance ...................................................................................................................141
16.3 Production address . ................................................................................................................143
16.4 Importers contact information ......................................................................................................143
R5909057 MCM-50 17/05/2016 3

Table of contents
4R5909057 MCM-50 17/05/2016

1. Safety instructions
1. SAFETY INSTRUCTIONS
About this chapter
It is necessary to read this chapter prior to starting any activity on the device. It contains valuable and critical information to ensure
safety of the operator, other people in the neighborhood of the device.
Overview
• Notice on safety
• Installation instructions
• Owner’s record
• Warnings
• Plug types
• Heat and fire hazard
• Installation
• Prevent personal injury
• Device damage
• Environment condition check
• Service
• Cleaning
• Repacking
1.1 Notice on safety
Notice on Safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1,
UL60950-1 and CAN/CSA - C22.2 No.60950-1, which are the safety standards of information technology equipment including
electrical business equipment. These safety standards impose important requirements on the use of safety critical components,
materials and isolation, in order to protect the user or operator against risk of electric shock and energy hazard, and having access
to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability
and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing ensures the
safety of the equipment to the user even when the equipment’s normal operation fails.
1.2 Installation instructions
Installation Instructions
• Before operating this equipment please read this manual thoroughly, and retain it for future reference.
• Installation and preliminary adjustments can be performed after reading the documentation manuals in detail.
• All warnings on the device and in the documentation manuals should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
1.3 Owner’s record
Owner’s Record
The part number and serial number can be found on the label at the back side of the device. Record these numbers in the table
below. Refer to them whenever you call your Barco dealer regarding this product.
Part Number:
Serial Number:
Dealer:
R5909057 MCM-50 17/05/2016 5

1. Safety instructions
1.4 Warnings
Safety warnings
• To prevent fire or electrical shock hazard, do not expose this equipment to rain or moisture!
• This product should be operated from an AC source with the supplied AC mains power adapter. The power input of the AC
mains power adapter is auto ranging from 100V to 240V.
• All equipment in the system is equipped with a 3-wire grounding plug, a plug having a third (grounding) pin. This plug will only
fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
the cord, pull it out by the plug. Never pull the cord itself.
• If an extension cord is used with this product, make sure that the total of the Ampere ratings on the products plugged into the
extension cord does not exceed the extension cord Ampere rating.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electrical shock.
• Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it
checked by qualified service personnel before resuming operations.
• Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
1.5 Plug types
WARNING:The AC mains power adapter must be grounded (earthed) via the supplied 3 conductor AC power
cable. If the supplied power cable is not the correct one, consult your dealer.
Plug types
a. Mains lead (AC Power cord) with CEE 7 plug up to 16 A
CEE 7
E
NL
Image 1-1
The colors of the mains lead are colored in accordance with the following code:
Green + yellow: Earth (Ground)
Blue: Neutral
Brown: Line (Live)
b. PowercordwithNEMA5/15plugupto15A
NEMA 5/15
E
L
N
Image 1-2
The wires of the power cord are colored in accordance with the following code.
Green or yellow + green: Earth (Ground)
Blue or white: Neutral
Brown or black: Line (Live)
6R5909057 MCM-50 17/05/2016

1. Safety instructions
1.6 Heat and fire hazard
Heat and Fire Hazard
Warning – risk of fire: do not place flammable or combustible materials near the device!
Barco products are designed and manufactured to meet the most stringent safety regulations.
This device radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and
safe. Exposing flammable or combustible materials into close proximity of this device could result in the spontaneous ignition of that
material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of
the device where no flammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16”) for all
Barco devices. Do not cover the device or the lens with any material while the it is in operation.
Keep flammable and combustible materials away from the device at all times.
Mount the device in a well ventilated area away from sources of ignition and out of direct sun light.
Never expose the device to rain or moisture.
In the event of fire, use sand, CO2, or dry powder fire extinguishers; never use water on an electrical fire.
Always have service performed on this device by authorized Barco service personnel.
Always insist on original Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this
device.
Slots and openings in the cabinet and the sides are provided for ventilation; to ensure reliable operation of the device and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface.
This device should never be placed near or over a radiator or heat register, nor should it be placed in a built-in installation or enclosure
unless proper ventilation is provided.
Rooms must be well ventilated or cooled in order to avoid build up of heat.
1.7 Installation
Safety On Installation
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it.
• Do not use this equipment near water.
• Only use the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
• Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or
heat register, nor should it be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Do not block the device’s cooling fans or free air movement around the device. Loose papers or other objects may not be
nearer to the device than 10 cm (or 4") on any side.
• Always ensure the working load limit of the structure supporting the device.
1.8 Prevent personal injury
To prevent personal injury
To prevent injuries and physical damage, always read this manual and all labels on the system before connecting to the wall outlet.
To prevent injuries, take note of the weight of the device.
Before attempting to remove any of the device’s covers, you must turn off the device and disconnect from the wall outlet.
1.9 Device damage
To prevent device damage
In order to ensure that correct airflow is maintained, and that the device complies with Electro-Magnetic Compatibility requirements,
it should always be operated with all of it’s covers in place.
Ensure that nothing can be spilled on, or dropped inside the device. If this does happen, switch off and unplug the mains supply
immediately. Do not operate the device again until it has been checked by qualified service personnel.
R5909057 MCM-50 17/05/2016 7

1. Safety instructions
The device must always be mounted in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the
hot air exhausted from its cooling system. Heat sensitive materials should not be placed in the path of the exhausted air.
1.10 Environment condition check
Environment condition check
A device must always be mounted in a manner which ensures the free flow of clean air into the device’s ventilation inlets. For
installations in environments where the device is subject to excessive dust, then it is highly advisable and desirable to have this dust
removed prior to it reaching the device clean air supply. Devices or structures to extract or shield excessive dust well away from the
device are a prerequisite; if this is not a feasible solution then measures to relocate the device to a clean air environment should be
considered.
It is the clients responsibility to ensure at all times that the device is protected from the harmful effects of hostile airborne particles
in the environment of the device. The manufacturer reserves the right to refuse repair if a device has been subject to negligence,
abandon or improper use.
Ambient temperature conditions
Max. ambient temperature : +40°C or 104°F
Min. ambient temperature : 10°C or 51°F
Storage temperature: -35°C to +65°C (–31°F to 149°F)
Humidity Conditions
Storage: 0 to 98% relative humidity, non-condensing
Operation: 0 to 95% relative humidity, non-condensing
Environment
Do not install the device in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive
dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not excessive.
Environment condition check
The device must always be mounted in a manner which ensures the free flow of clean air into the air intake and out of the air outlet.
1.11 Service
Safety On Servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and
risk of electric shock!
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the equipment.
• If the product has been exposed to rain or water.
• If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
• If the product has been dropped or the cabinet has been damaged.
• If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technician has used original BARCO replace-
ment parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized
substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitu-
tions may void warranty.
• Safety check: Upon completion of any service or repairs to this device, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
8R5909057 MCM-50 17/05/2016

1. Safety instructions
1.12 Cleaning
Safety On Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these
will damage the cabinet.
1.13 Repacking
On Repacking
Save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment. For maxi-
mum protection, repack your set as it was originally packed at the factory.
R5909057 MCM-50 17/05/2016 9

1. Safety instructions
10 R5909057 MCM-50 17/05/2016

2. Introduction
2. INTRODUCTION
About this chapter
This chapter is an overview of the manual’s layout, symbols and fonts used in this manual. It also introduces you to the Barco
MCM-50 external warp box and describes its features and controls.
Overview
• About this manual
• Symbols and fonts
• Key features and benefits
Model certification name
Model certification name: MCM-400
2.1 About this manual
CAUTION:For the latest version of the product manuals, see http://www.barco.com.
CAUTION:Always check for the latest firmware version the Barco website (http://www.barco.com) and select
myBarco on top of the page. Login to the secured website and browse to your product.
Description
This manual contains all essential information for the operator to make full use of the MCM-50 external warp box. It includes the
description of the warp box functionalities and capabilities, its operation, and step-by-step procedures for accessing controls.
This manual includes the following chapters:
1. Safety: safety instructions to be followed when operating the device.
2. Introduction: general information about the manual and about the device.
3. Packaging: overview of the deliverables and unpacking instructions.
4. Facility and system requirements: lists requirements and guidelines.
5. Physical installation: instructions to install the device and to make all connections.
6. Setup and configuration: setup of resolution, external communication and linking configuration.
7. Getting started: starting the device and displaying a source.
8. OSD preferences: Customizing the On Screen Display (OSD) or menu.
9. Basic operation:first level (= operator) features and image alignment
10. Advanced operation: second level (= specialist) features and alignment, such as mid-level geometry and color alignment.
11. Expert operation: third level (= expert) features and alignment, such as high end geometry, color and blending alignment.
12. Maintenance and troubleshooting: lists maintenance activities and troubleshooting tips.
13. MCM-50 tools: tools to perform a wide range of actions and to customize the device for your application.
The appendix includes Specifications, detailed information about the Remote Control Unit (RCU) and On Screen Display (OSD or
menu) and environmental information.
R5909057 MCM-50 17/05/2016 11

2. Introduction
2.2 Symbols and fonts
Symbol overview
The following icons are used in the manual :
Caution: provides information on potential hazards.
Warning: provides information on potential hazard that can lead to personal injuries.
Info: general information (about a term).
Note: additional information about the subject.
Tip: useful advice about the subject.
Font overview
• Buttons and keys are indicated in bold.
• Menu items are indicated in italic.
• Step related notes, tips, warnings and cautions are printed in italic.
• Procedure related notes, tips, warnings and cautions are printed in bold between 2 lines preceded by an icon.
2.3 Key features and benefits
Key features and benefits
The MCM-50 external warp box is intended to be used together with the F50 projector projector.
The MCM-50 external warp box offers following key features and benefits:
• Real time warping with minimal latency;
• Using proprietary advanced scaling algorithms to retain maximal detail;
• Advanced color matching using linked Dynacolor algorithms;
• Electronic blend generation;
• Pixel based alpha/beta plane correction for black/highlight levels;
• Native and scaled pattern generation;
• Supports active and passive stereo formats;
12 R5909057 MCM-50 17/05/2016

3. Packaging
3. PACKAGING
About this chapter
This chapter provides an overview of what is in the box and how to unpack.
Overview
• Content
• Unpacking
3.1 Content
No DisplayPort cable is delivered with the kit. A good shielded DisplayPort cable is necessary for good EMI
performance. Bad DisplayPort cables cause loss of the image and the image only recovers by reconnecting
the DisplayPort cable.
What’s in the box
The items listed in the table below are delivered along with the device. Ensure that everything is present and intact. Contact your
local dealer or Barco if anything is missing or damaged. Never use a damaged unit (e.g. MCM-50, power cord, power adaptor,
RCU).
Description Article number Image Quantity
MCM-50 R9898503 1
Remote Control Unit
(RCU) + 2 batteries
R764277K 1
12 VDC power
adaptor
B557282 1
R5909057 MCM-50 17/05/2016 13

3. Packaging
Description Article number Image Quantity
Power cord
(connectors C13
and NEMA 5-15)
V326111 1
Power cord
(connectors C13
and CEE7)
R326103 1
Rack mount R874169 1
Screws to tighten the
rack mount
B364484 10
User Guide R5909057 1
Safety Guide R5905189WW 1
3.2 Unpacking
Packaging
Cardboard boxes and foam are used for maximum protection during shipment.
14 R5909057 MCM-50 17/05/2016

3. Packaging
Save the original packaging for future shipment. For maximum protection while shipping the unit, always
pack it as it was packed during first delivery.
Unpacking the MCM-50
1. Carefully cut the tape on the top lid of the box
Warning: Follow the relevant safety precautions while using a knife.
2. Open the box and lift out the content.
Image 3-1
R5909057 MCM-50 17/05/2016 15

3. Packaging
16 R5909057 MCM-50 17/05/2016