basIP BR-AA14 User manual

USER MANUAL
BRACKET
BR-AA14

BR-AA14
Device description
BRACKET
A bracket for wall mount dedicated
to AA-14FB multi-apartment
outdoor panel.
Main features
• Dimensions: 185 x 407 x 107 mm
• Colors: Gold, Silver, Black
• Gross weight: 0.67 kg
• Case: Metal
BR-AA14 bracket. Wall mount.
185 mm
400 mm
45 mm
Measure the dimensions of the bracket needed to mark the location
of the intended installation on the wall for further mounting the bracket.
1
107 mm
407 mm
185 mm

EAN: 5060514913659 (BLACK)
EAN: 5060514913666 (SILVER)
EAN: 5060514913673 (GOLD)
Check the availability of all components required for installation,
connection and fastening.
fastening
screws
x4
fastening
anchor
dowels
x4
wall mount
bracket
BR-AA14
x1
panel
fastening
bolts
x4
connection
cords
x5
2
On the wall, draw a rectangle
according to the dimensions
done in the previous step.
3Place the wall mount bracket
on the wall and outline places
for anchor dowels mount
opposite the holes in the bracket.
4
185 mm
407 mm
1090-1300 mm
Put aside the bracket and make
holes in the outlined places with
a perforator.
5Hammer the anchor dowels into
the resulting holes.
6

Wire all the necessary cables for
panel connection and switching
(for Ethernet, an exit button,
a lock, panel power, a door sensor,
a fire alarm, RS485, and Wiegand
interfaces) out of the wall within
the drawn rectangle.
7Place the wall mount bracket
to the installation place on the
wall and fasten it with screws
through the mounting holes.
At the same time, pass all the
protruding from the wall wires
through the corresponding hole
in the bracket.
8
Cut out a rectangle of 80x40 mm
from foamed polyurethane or
rubber. In the rectangle, make
holes opposite the required
outgoing connectors on the
panel rear side.
9
80 mm
40 mm
Pass all wires through the made
earlier holes in the insulating
rectangle.
10

Switch and connect the
protruding from the wall
and passing through the
insulating rectangle wires to the
necessary connection cords from
the panel kit.
11 Join all the resulting connectors
at the ends of the wires to their
corresponding response parts
on the panel rear side.
12
EAN: 5060514913659 (BLACK)
EAN: 5060514913666 (SILVER)
EAN: 5060514913673 (GOLD)
Apply a thin layer of silicone
sealant along the perimeter
of the niche with the connectors
оn the panel rear side and place
the protective rectangle in a niche
(where all connectors are)
on the panel rear side.
13
Silicon
sealant
Apply a 3-4 mm layer of silicone
sealant around the niche with
the placed insulating rectangle,
so that the sealant falls precisely
on the joint of the rectangle
and the back plastic cover
of the panel.
14
Silicon
sealant
Tape

14
Apply a 3-4 mm layer of silicone
sealant around all wires coming
out of the slots in the insulating
rectangle.
The sealant must be applied
to the top of the joint between
the wire and the insulating
rectangle.
15
Put all connected to the panel
wires on the bottom of the surface
mount bracket.
All the protruding from the wall
and connected to the panel wires
must be carefully bent in
a semicircle in so that the upper
part of the wiring bundle is higher
than the hole for inserting cables
from the wall into the inside
of the bracket.
16
Silicon
sealant

Install the entrance panel inside
the surface mount bracket.
Important!
Hold the wiring bundle
on the bottom of the bracket
so that some wires do not fall
on the sharp edges and are not
pressed by the panel.
Fasten the entrance panel
to the bracket with the fastening
bolts from the kit.
17
18
EAN: 5060514913659 (BLACK)
EAN: 5060514913666 (SILVER)
EAN: 5060514913673 (GOLD)

www.bas-ip.com