Uplift Desk MON041 User manual

Enfield Single Monitor Arm
MON041
For assembly assistance,
visit upliftdesk.com/contact,
call 800-349-3839,
or email [email protected]
©2023 UPLIFT Desk®. All Rights Reserved
Scan QR code for
product webpage

2
Base Lower Arm Upper Arm Lower Clamp Upper Clamp
VESA Plate Wire Cover Upper Base Plate Lower Base Plate
Package Contents
Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from
improper use of this product. Please provide these instructions to any new user or owner of the product.
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result
in damage or personal injury. Retain manual for future reference.
Warning: This product contains a spring mechanism that can cause injury. Be careful when
removing monitors as the arm can spring up when the weight of the monitor is removed.
Safety and Warnings
Allen Wrenches
Set of two: 4mm, 6mm M6 x 12 Flathead Screw qty 3
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
M4 x 12 Screw (M-A)
qty 4
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
M5 x 12 Screw (M-B)
qty 4
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
M5 Washer (M-C)
qty 4
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
M8 Washer M8 Nut Flat Wrench Long Bolt
Hardware Components

3
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
Assembly Instructions
WARNING: This product contains a spring mechanism that can cause injury. Be careful when removing monitors as the arm can
spring up when the weight of the monitor is removed.
Note: There are two ways to attach to your desktop: Clamp and Bolt-through mount. Determine if you need to attach it around the
back side of your desk or through a hole from 0.4’’ to 3.15’’ in diameter.
Acceptable monitor weight range: 4.4 to 19.8 lb (per monitor)
Desktop thickness compatibility: Clamp Method: 0.4”-3.3” thick | Bolt-through Method: 0.4”-3.1” thick
Step 1
Determine your mounting method. There are two ways to
attach the Eneld Single Monitor Arm to your desktop:
Clamp Method: If you would like to attach the monitor
arm along the back edge of your desktop, follow the
Clamp Method instructions (Steps 2 - 4).
Bolt-Through Method: If you prefer to attach the monitor
arm through your desktop, skip Steps 2 - 4 and follow the
Bolt-Through Method instructions (Steps 5 - 7).
Step 2 (Clamp Method)
Align the Upper Clamp with the Base in the orientation
shown and attach it using the three M6 x 12 Flathead
Screws and the 4mm Allen Wrench.
Clamp Method Bolt-Through Method

4
g. 2
3.1”
.4”
g. 1
.25”
Step 5 (Bolt-Through Method)
Ensure the desktop has a hole between 0.4’’ and 3.1’’ in
diameter to use this option.
Using a grommet hole that is already in your desktop is
acceptable, or you can drill a 0.5” diameter hole anywhere
on your desktop.
Step 3 (Clamp Method)
A. There are two sets of holes in the Upper Clamp to use
for different desktop thicknesses.
• There are two screws pre-installed in the top two
holes of the Upper Clamp. Leave the screws in those
holes if your desktop is between 0.4’’ and 2.1’’ thick
(g. 1)
• If your desktop is between 2’’ and 3.3’’ thick, use the
4mm Allen Wrench to remove the screws from the
top two holes and insert them into the bottom two
holes (g. 2)
B. Use the 4mm Allen Wrench to adjust the two screws in
the Upper Clamp so that there is about 0.25” of thread
between the plate and screw heads.
C. Position the Lower Clamp assembly in the orientation
shown and press it against the Upper Clamp so the
two screws go through the two key slot holes in the
Lower Clamp.
D. Slide the Lower Clamp assembly down so that the
screws are at the top of the key slot holes and tighten
the screws with 4mm Allen Wrench.
Step 4 (Clamp Method)
A. Using the knob screw, adjust the bolt on the bottom of
the Lower Clamp so that the opening is wide enough to
accommodate the thickness of the desktop.
B. Slide the assembly onto the back of the desktop,
then tighten the knob screw to secure the Base to the
desktop.

5
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
180˚
360˚
Step 6 (Bolt-Through Method)
A. From the top of the Upper Base Plate (the side opposite
from the countersunk holes), insert the Long Bolt
through the square hole until the square shank of the
Bolt ts into the Plate’s square hole.
B. Align the Upper Base Plate with the bottom of the base
in the orientation shown and attach it using the three
M6 x 12 Flathead Screws and the 4mm Allen Wrench.
Step 7 (Bolt-Through Method)
A. Lower the Base assembly to the desktop guiding the
Long Bolt through the hole in the desktop.
B. Slide the Lower Base Plate onto the Long Bolt and
secure it against the desktop with the M8 Washer and
Nut.
C. Tighten the Nut with the Flat Wrench while ensuring
the Lower Base Plate straddles the hole.
D. Proceed with the Arm Assembly & Monitor Mounting,
Step 8.
Step 8
A. The Base comes with a pre-installed limiting screw
in the post which limits the rotation of the arm to 180
degrees. If you want to limit the rotation of the arm
to 180 degrees, leave this screw installed and use the
4mm Allen Wrench to ensure it is tight (be careful not
to overtighten).
B. If you want the arm to rotate a full 360 degrees, remove
this screw with the 4mm Allen Wrench.
Note: We recommend saving the screw in case you
decide to limit the rotation of the arm in the future.
Step 9
Slide the Lower Arm onto the post of the Base until it
is fully seated and tighten the set screw at the back of
the Lower Arm with the athead end of the 4mm Allen
Wrench (or a small at head screwdriver). This will secure
the Lower Arm to the Base and keep it from becoming
separated during adjustment.

6
Step 11
Reminder: The acceptable monitor weight range for the
Eneld Single Monitor Arm is 4.4 lb to 19.8 lb.
A. Lay your monitor face down on a clean surface or a
towel to prevent damage to your screen.
B. Test the M4 x 12 and M5 x 12 Screws in your monitor’s
screw holes to determine which is the right size for
your monitor.
C. Line up the holes of the VESA Plate with the holes on
your monitor, orienting the VESA Plate as shown, with
the VESA Plate’s knob pointing toward the top of the
monitor.
D. Attach the VESA Plate to the monitor using the
selected screws with the M5 Washers.
top
Step 10
Warning, Pinch Point: Pay attention! When handling the
Upper Arm, keep hands and ngers clear of the Upper
Arm’s pivot location when moving, installing, and making
adjustments to the Eneld Monitor Arm.
A. Slide the post of the Upper Arm into the hole at the top
of the Lower Arm until it is fully seated.
B. Tighten the set screw on the front of the Lower Arm
with the at-head end of the provided 4mm Allen
Wrench (or a small at head screwdriver). This will
prevent the Upper Arm from becoming separated from
the Lower Arm during adjustment.
Step 12
A. Make sure the knob on the VESA Plate is in the
“Unlock” position, perpendicular to the monitor.
B. Slide the VESA Plate into the slot shown in the Upper
Arm.
C. Once the VESA Plate is inserted all the way into the
Upper Arm, turn the knob on the VESA Plate to the
“Lock” position, parallel to the monitor.
D. Pull up slightly on your monitor to make sure it is
locked securely in place.

7
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
Step 13
A. Move the monitor to any position and release it. If the
monitor does not drift up or down, the arm is properly
counterbalanced.
B. If the monitor does not remain where you positioned
it, you will need to adjust the tension of the spring to
properly support the weight of your monitor using the
6mm Allen Wrench on the tension adjustment screw
(located at the back end of the Upper Arm). View how
much the spring is tensioned via the tension indicator
on top of the Upper Arm.
Caution: To prevent damage to the tension indicator,
never adjust the counterbalance screw so that the red
indicator line moves past the “+” or “-” symbols.
• If the monitor drifted down, hold the Upper Arm in a
horizontal position and use the 6mm Allen Wrench
to turn the adjustment screw so that the tension
indicator moves toward the “+” symbol until the
monitor remains in place when you let go.
• If the monitor drifted upward, turn the adjustment
screw so that the tension indicator moves towards
the “-” symbol until the monitor remains in place
when you let go.
Step 14
A. You can rotate the monitor to be in either portrait or
landscape orientation.
B. If the monitor does not hold in place when rotated,
tighten the screws shown with a Phillips Head
screwdriver to keep the monitor in position.
Step 15
A. To adjust the front and back tilt of your monitor, loosen
the socket head screw on the side of the Upper Arm
where shown with the 4mm Allen Wrench.
B. Once the monitor is at your preferred viewing angle,
re-tighten the screw with the Allen Wrench to hold the
monitor in place.

8
Step 16
A. To use the arm’s wire management, rst remove the
built-in wire covers.
B. There are two wire covers the arm, one located under
the Upper Arm and the other under the Lower Arm. They
are removed by gripping the sides of the cover and
sliding it forward (toward the monitor) to unlock and
remove. Be careful not to pull down on the cover, doing
so may damage the covers.
C. Run your cables up and under each section of the
monitor arm and replace the covers the opposite way
that they were removed.
Step 17
A. If you have selected the Clamp Method, you can now
snap the Wire Cover onto the back of the Upper Clamp
on the Base as shown and insert your monitor cables
through the integrated clip.
B. In addition to holding the cables in place, there are
convenient holes to store the Allen Wrenches for future
adjustment needs.
C. The Wire Cover adds 0.75” to the back of the monitor
arm. If your desk is close to a wall or cubicle, or has
a privacy panel attached to the back of the desktop,
there may not be enough space available to attach the
Wire Cover.
Monitor Tilt
The Monitor can tilt at the VESA mount forward or
backward within a range of 80° (+/-40°).
Height Adjustment
The center of the VESA mount can go as high as 18.5” and
as low as 8.7’’ from the desktop.
8.7”
18.5”
80˚

9
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
Monitor Swivel
The Monitor can swivel 180° (+/-90°) at the hinge at the
top of the Upper Arm.
Monitor Rotation
The Monitor can rotate at the VESA mount 360°
allowing landscape or portrait viewing.
Upper Arm Swivel
The Upper Arm can swivel 180° (+/-90°).
Lower Arm Swivel
A. The Lower Arm can swivel a full 360°. It can also be set
to allow only a range of 180° (See Step 8).
Note: We do not recommend swiveling the Monitor
past the back of the desk as this may cause instability.
90˚
90˚
180˚
360˚

10
Notes

11
© UPLIFT Desk • 800-349-3839 • [e-mail] • upliftdesk.com
Notes

SAVE THIS MANUAL
Study this manual carefully. If this product is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
Work Better. Live Healthier
AI-MON041-1.2
Copyright Notice: This manual is a component of this UPLIFT Desk product. This manual is a
part of the scope of delivery, even if the item is resold. This manual is also available on the
UPLIFT Desk website: upliftdesk.com. This manual is subject to United States copyright law.
©
upliftdesk.com
[email protected]
800-349-3839
512-614-3152