Bazooka REAR SPEAKER Guide

TOYOTA FJ CRUISER 2007 - REAR SPEAKER UPGRADE
Preparation
Part Number: TMS-SA-FJ
Code:
Kit Contents
Item # Quantity Reqd. Description
1 2 Rear Speaker Assembly
2 2 Replacement Grilles
Southeast Toyota Distributors LLC
Hardware Bag Contents
Item # Quantity Reqd. Description
1 8 Push nuts for Grilles
Additional Items Required For Installation
Item # Quantity Reqd. Description
Conflicts
Conflicts with factory installed rear speakers
Recommended Tools
Personal & Vehicle
Protection Notes
Vehicle Protection Seat/Floor Covers
Part Protection Blankets
Special Tools Notes
Dremel Tool
Dremel Cable Tool
FJ Cable Tool Guide
Installation Tools Notes
Panel Removal Tool Nylon Removal Tool (NRT)
Pliers 1. Diagonal Cutters
2. Long Nose (optional)
Screwdriver Magnetized Philips # 2
Screwdriver Magnetized Philips # 1
Panel Cutout Template Spiral Bit
Torque Wrench 36”lbs 3/32” Drill Bit
Special Chemicals Notes
Cleaner
General Applicability
Conflicts with factory installed rear speakers
Recommended Sequence of Application
Item # Accessory
1 Install Security/Audio
2 Install Bazooka Tube
3 Install Door Sills
4 Install Molded Dash *Mandatory
Vehicle Service Parts (may be required for reassembly)
Item # Quantity Reqd. Description
1
Legend
Speaker Specifications / Replacement Parts
Size 3.5 inch (nominal)
Frequency Response 125 Hz – 20kHz
Magnet Size 8 oz.
Efficiency 90 dB
Power Handling 45 watts each
Weight 2 lbs.
Impedance 4 ohms
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
SPECIAL NOTE: Installation Sequences
A
fter TMS and Safety mandated preparatory steps have been
taken, the installation sequence is the suggested method for
completing the accessory installation. In some instances the
suggested sequence is written for one associate to install and in
others the sequence is given as part of a team accessory
installation. Unless otherwise stated in the document, the
associates may perform the installation steps in any order to
make the installation as efficient as possible while maintaining
consistent quality.
Page 1 of 5 pages

TOYOTA FJ CRUISER 2007 - REAR SPEAKER UPGRADE
Procedure
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:-
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
. Fig. 1A Fig. 1B
1. Install Speaker.
(a) Using NRT, remove blank panel. Fig 1A.
(b) Plug wiring harness into plug behind panel.
Fig 1B.
(c) Hold speaker in place, and hand tighten
silver screws as indicated to swing locks
out behind speaker assembly until tight
against sheet metal. Over tightening could
break assembly. Fig 1C.
Southeast Toyota Distributors LLC
Fig. 2A
Fig. 2B Fig. 3A
Fig. 1C
2. Cut Speaker Cover
(a) Using supplied template and Dremel tool,
cut the panel as shown in figure 2A.
(b) Using supplied template drill (4) 3/32 holes
in panel as shown in figure 2B.
3. Install Grille into Speaker Cover
NOTE: Use side cutters to trim ribs on back of
cover. Fig 3A
(a) Using supplied push nuts, carefully secure
four mounting posts on Grille as shown in
figure 3A
(b) Reinstall Speaker Cover / Grille Assembly.
.
Page 2 of 5 pages

TOYOTA FJ CRUISER 2007 - REAR SPEAKER UPGRADE
Checklist - these points MUST be checked to ensure a quality installation.
Check: Look For:
Accessory Function Checks
Turn on Radio
Verify CD & Satellite Tuner (if equipped)
Antenna is functioning
Vehicle Function Checks
Hazard Button
HVAC
Rear Window Defogger
Passenger Seat Belt Warning Light
Radio display turns on & sound is heard
CD player functions & Satellite Tuner
stations are playing (if equipped)
Reception of AM/FM stations
.
Functioning Hazard Lights
All HVAC controls function properly
Functioning Rear Window Defogger
Functioning Seat Belt Warning Light
Page 3 of 5 pages
Southeast Toyota Distributors LLC

TOYOTA 2007 2007 - REAR SPEAKER UPGRADE
Troubleshooting
Troubleshooting
Condition: Check For:
No sound from Rear Speakers, however
factory speakers still play
Distorted Sound
Low Sound If Bass Tube installed.
Rattling Noises
1. Ensure speaker plugs are connected,
both at the plug into the vehicles harness
and on the back of the speaker.
1. Check for short in wiring between plug
and speaker.
1. Close the back hatch of the vehicle
2. Adjust the radio to a comfortable listening
level, and then turn the “gain control” knob
on the Bass Tube clockwise until the sound
becomes audible. Do not adjust the level too
high, as this will result in distorted sound.
Rattling will be evident in some panels at
extreme volume conditions, but make sure
you have performed the following to
minimize noise:
1. Securely tightened Mounting Hardware so
Speaker Assembly does not move.
Page 4 of 5 pages
Southeast Toyota Distributors LLC

TOYOTA FJ CRUISER 2007- REAR SPEAKER UPGRADE
Wire Harness & Radio Wiring Schematics
Wire Harness Schematics
WIRING CONNECTOR SCHEMATICS:
Speaker Connector Vehicle Harness Connector
Speaker Connector
Pin No. Wire Color Function
1 Black Speaker (+)
2 N/A Speaker (+)
Vehicle Harness Connector
Pin No. Wire Color Function
1 Speaker (+)
2 Speaker (+)
Page 5 of 5 pages
Southeast Toyota Distributors LLC