BDS 106-223 User manual

Service Manual
106-223
Post Mount Flex Arm System
w/ Friction Brake and Tray
Rev 2 - 1/14/20 900-086M

800.237.2303 503.538.8756 503.538.2845 Fax www.beaverstatedental.com
1
106-223
Installation 1. Place the shipping carton in the desired location. Remove the tray with arm
system and unit/light post (if ordered) from the shipping carton.
2. Insert the unit/light post into the chair adapter hub as designated by label on light
post which states "Adapter This Side." Level, then tighten the set screws to
secure the post in place.
3. Slide the arm stop collar and washer down the post. Tighten the set screws to
secure the stop collar at the desired height.
4. Slide the tray with arm system down the post until it rests on the stop collar and
washer.
5. Cut the safety tie strap and carefully release the arm system.
6. Toadjustthetensiononthemanualexarm,removethearmhousingcoverand
locatethetensionnut,refertoitem11oftheIPB106-216FlexArm.Makeyourad-
justment using a 5/8" open end wrench.
7. Toadjustthelevelofthetray,removethearmhousingcoveronthemanualexarm
andlocatetheadjustmentnut,refertoitem10oftheIPB106-216FlexArm.Make
youradjustmentusingamodied9/16"openendwrench(BSDp/n010-030).
WARNING
The arm system is spring loaded. Before removing
thesafetytiestrap,rmlygrasptheexarmandhold
down.

2
POST MOUNT FLEX ARM SYSTEM
W/FRICTION BRAKE
106-220
ITEM
1
2
3
4
5
6
7
8
9
PART DESCRIPTION
Plug, 3/4"................................................
Flex Arm. ................................................
Small Nyliner Bushing.......................
Thrust Washer, Small..........................
Ridgid Arm.. ..........................................
Nyliner Bushing...................................
Thrust Washer, Large .........................
Post Ring. ...............................................
Set Screw, 8-32 x 3/16"......................
PART NUMBER
010-005
106-216
013-012
106-333
106-031
013-007
106-334
106-028
005-021
QTY
1
1
1
1
1
2
1
2
4

3
ITEM
1
2
3
4
5
6
7
PART DESCRIPTION
Arm Pivot.............................................
Bushings, Flex Arm...........................
Pivot Bushing, 1/4" x 1-1/8"...........
Pin, Housing Mech Flex ..................
Arm Housing......................................
Arm Pivot Bushing ...........................
Pin,Tapered,Threaded....................
PART NUMBER
106-228
013-020
003-036
009-013
106-234
013-018
009-004
ITEM
8
9
10
11
12
13
14
ITEM
15
16
17
18
19
20
21
22
PART DESCRIPTION
Nyliner Bushing............................
Rod End...........................................
Adjusting Nut................................
Tension Nut....................................
Spring ..............................................
Screw 10-32 x 1/4" ......................
Rod....................................................
PART DESCRIPTION
Friction Cup............................................
Friction Cone..........................................
Spring Stop.............................................
Flex Arm Knuckle..................................
Screw 6-32 x 1/4"..................................
Arm Housing Cover.............................
Plug ...........................................................
Bushing....................................................
PART NUMBER
013-012
106-015
106-011
002-019
008-016
001-087
106-007
PART NUMBER
106-010
106-012
106-009
106-229
001-133
106-235
010-005
013-004
QTY
1
4
4
2
1
1
2
QTY
1
1
2
1
1
2
1
QTY
2
1
1
1
1
1
1
1
FLEX ARM
106-216

4
TRAY AND MOUNT
105-065 AND 106-203
ITEM
1
2
3
PART DESCRIPTION
Control....................................................
Tray holder with holder bar.............
Holder bar.............................................
PART NUMBER
106-203
105-065
105-006
QTY
1
1
1

WARRANTY
BDS warranties its product to be free of defects in material and workmanship for SEVEN FULL YEARS from the
date of purchase on all units. Auto-blocks and standard foot controls are covered by a LIFETIME warranty when
factory installed as part of a complete dental system. Upholstery has a TWO YEAR warrany and does not cover
normal wear, stains, cuts or tears. Our LED lights have a FIVE year Warranty and our halogen light has a ONE year
Warranty. Operatory chair motors feature a TEN year warranty. All warranty is limited to repair or replacement
by BDS. Products returned to the factory and determined to be defective will be repaired or replaced free of
charge at discretion of BDS. The warranty does not cover light bulbs, electrical components and trimmed or
installed tubing. BDS reserves the right to void all warranties if any product is installed by other than an authorized
technician. BDS' warranty does not cover damage to any surface finish, including but not limited to, discoloration
or abrasion from cleaners, disinfectants or light sources. No claim for labor or consequential damages will be
allowed. Return items must include a copy of the invoice or packing slip as proof of purchase.

Beaverstate Dental Inc.
115 S. Elliott Rd.
Newberg, OR 97132
800-237-2303
503-538-8756
503-538-2845 Fax
www.beaverstatedental.com