Beko DC 7120 User manual

DC 7120
Dryer
干衣机

Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and
passed through a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and
keep it for future reference.
This User Manual will
• Help you use your machine in a fast and safe way.
• Read the User Manual before installing and starting your product.
• In particular, follow the instructions related to safety.
• Keep this User Manual within easy reach for future reference.
• Please read all additional documents supplied with your product.
Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
A Important safety information. Warning for hazardous situations with regard to
life and property.
BCaution; Warning for supply voltage.
Caution; Warning for fire hazard.
Caution; Warning for hot surfaces.
Read the instructions.
C Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect the environment
by dropping it off in the municipal receptacles provided for this purpose. Your appliance also
contains a great amount of recyclable material. It is marked with this label to indicate the
used appliances that should not be mixed with other waste. This way, the appliance recycling
organised by your manufacturer will be done under the best possible conditions, in compliance
with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact
your town hall or your retailer for the used appliance collection points closest to your home. We
thank you doing your part to protect the environment.
2960310397_EN/040211.1749

3EN
1Important safety information
This section includes safety information that
will help protection from risks of personal
injuries or materialistic damages. Failure
to follow these instructions shall cause
any warranty and reliability commitment to
become void.
General safety
• Never place the machine on a carpet-
covered floor, otherwise, lack of airflow
beneath the machine may cause
electrical parts to overheat. This will
cause problems with your machine.
• If the power cable or mains plug is
damaged, you must call Authorised
Service Agent for repair.
• The product should not be plugged
in during installation, maintenance
and repair works. Such works should
always be made by the technical
service. Manufacturer shall not be held
responsible for damages arising from
processes carried out by unauthorised
persons.
• Connect the product to a grounded
outlet protected by a fuse of suitable
capacity as stated in the technical
specifications table.
• Operate your product at temperatures
between +5°C and +35°C.
• Do not use electrical devices in the
product.
• Do not connect the air exit of the product
to the chimney holes which are used
for the exhaust fumes of the devices
operating with gas or other types of fuel.
• You must provide enough ventilation
in order to prevent gases exiting from
devices operating with other types of
fuels including the naked flame from
accumulating in the room due to the
back fire effect.
• Always clean the lint filter before or after
each loading.
• Never operate your dryer without the lint
filter installed.
• Do not allow fibre, dust and dirt
accumulation around the exhaust exit
and at adjacent areas.
• Power cable plug must be within easy
reach after installation.
• Do not use extension cords, multi-plugs
or adaptors to connect the dryer to
power supply in order to decrease the
risk of electric shock.
• Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a
qualified electrician change the socket
with a suitable one.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should not
be dried in the product since they emit
flammable or explosive vapor.
• Do not dry items cleaned with industrial
chemicals in the dryer.
• Do not dry unwashed items in the dryer.
• Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty
of detergent before being dried in the
dryer.
• Garments or pillows bolstered with
rubber foam (latex foam), shower
bonnets, water resistant textiles,
materials with rubber reinforcement and
rubber foam pads should not be dried in
the dryer.
• Do not use fabric softeners and
anti-static products unless they are
recommended by the manufacturers of
the fabric softener or the product.
• This product must be grounded.
Grounding installation decreases the risk
of electric shock by opening a path with
low resistance for the electricity flow in
case of a malfunction or failure. Power
cable of this product is equipped with
a conductor and a grounding plug that
allows for grounding the product. This
plug must be installed appropriately and
inserted into a socket which is grounded
in accordance with the local laws and
regulations.
• Do not install the product behind a door
with a lock, sliding door or a door that
has a hinge against the hinge of the
dryer.

4EN
• Do not install or leave this product
in places where it will be exposed to
outdoor conditions.
• Do not tamper with the controls.
• Do not perform any repair or part
replacing procedures on the product
even if you know or have the ability to
perform unless it is clearly suggested
in the operating instructions or the
published service manual.
• Inside and exhaust duct of the product
must be cleaned by the qualified service
personnel periodically.
• Wrong connection of grounding
conductor of the product can cause
electric shock. If you have any suspect
about the grounding connection, have
it checked by a qualified electrician,
service representative or service
personnel.
• Do not reach into the machine when the
drum is spinning.
• Unplug the machine when it is not in
use.
• Never wash down the appliance with
water! There is the risk of electric shock!
Always disconnect by unplugging from
the mains before cleaning.
• Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out by grabbing the plug
only. Do not operate the machine if the
power cable or plug is damaged!
• Never attempt to repair the machine
yourself, otherwise, you will be putting
your life and others’ lives in danger.
• For malfunctions that cannot be solved
by following the information given in the
safety instructions:
Turn off the machine, turn off and
contact an authorised service agent.
• Do not stop the dryer before the drying
cycle comes to an end unless you will
remove all laundry from the dryer fast in
order to lay them and dissipate the heat.
• Remove the door of the drying
compartment before decommissioning
or disposing of the product.
• The final step of the drying cycle (cool-
down cycle) occurs without applying
heat to ensure that the items are left at a
temperature that will not damage them.
• Fabric softeners or similar products
should be used as specified by the
fabric softener instructions.
• Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result
if metal reinforcements come loose
during drying.
• Check all garments for forgotten
lighters, coins, metal pieces, needles,
etc. before loading.
• At times when your dryer is not in use or
after the laundry is taken out following
the completion of drying process, turn
off by using the On/Off button. In cases
when the On/Off button is on (while the
dryer is energized), keep the door of the
dryer closed.
Intended use
• This product has been designed for
domestic use. It should not be used for
other purposes.
• Use the product only for drying laundry
that are marked accordingly.
• Dry only those articles in your product
that are stated in this manual.
• This product is not intended to be
used by persons with physical, sensory
or mental disorders or unlearned or
inexperienced people (including children)
unless they are attended by a person
who will be responsible for their safety
or who will instruct them accordingly for
use of the product.
Children’s safety
• Electrical appliances are dangerous for
the children. Keep children away from
the machine when it is operating. Do
not let them tamper with the machine.
• Packaging materials are dangerous to
children. Keep the packaging materials
out of reach of children or dispose
them by classifying according to waste
directives.
• Do not allow children sit/climb on or
enter in the product.
• Children should be supervised to ensure
that they do not play with the product.
• Close the loading door when you leave
the area where the product is located.

5EN
2Installation
Refer to the nearest Authorised Service
Agent for installation of your product.
CPreparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections
must be carried out by a qualified
personnel.
APrior to installation, visually check if
the product has any defects on it. If
so, do not have it installed. Damaged
products will cause risks for your
safety.
Appropriate installation location
• Install the product in an environment
which has no risk of freezing and is in a
stable and level position.
• Operate your product in a well
ventilated, dust-free environment.
• Do not block the air ducts in front of
and under the product with materials
such as long pile rugs and wooden
bands.
• Do not place your product on a long
pile rug or on similar surfaces.
• Do not install the product behind a
door with a lock, sliding door or a
hinged door which can strike the
product.
• Once the product is installed, it should
stay at the same place where its
connections have been made. When
installing the product, make sure
that the rear wall of it does not touch
anywhere (tap, socket, etc.) and also
pay attention to install the product at a
place where it will stay permanently.
BDo not place the product on top of the
power cable.
• Keep at least 1.5 cm distance to walls
of other furniture.
Removing the transportation safety
assembly
ARemove the transportation safety
assembly before using the product for
the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum
that contains a piece of styrofoam.
Hold it from its section marked with XX.
3. Pull the nylon towards yourself and
remove the transportation safety
assembly.
AMake sure that you have removed
the transportation safety assembly
(nylon+styrofoam pieces) before using
the product for the first time. Do not
leave any items inside the drum.
Under counter installation
• A special part (Part no. 297 360 0100)
replacing the top trim must be provided
and installed by the Authorised Service
Agent in order to use the machine
under a counter or in a cupboard. It
should never be operated without the
top trim.
• Leave at least 3 cm of space between
the side and rear walls of the product
and the walls of the counter/cupboard
when installing your product under a
counter or in a cupboard.
Mounting over a washing machine
• A fitting device should be used
between the two machines when
installing above a washing machine.
The bracket (Part no. 297 720 0100
white/297 720 0200 grey) must be
installed by the Authorised Service
Agent.
• Place the product on a firm floor. If
it will be placed on top of a washing
machine, the approximate weight of
both machines may reach 180 kg when
they are full. Therefore, the floor must
be capable of carrying the load on it!
Adjusting the feet
In order to ensure that your machine
operates more silently and vibration-free,
it must stand level and balanced on its

6EN
feet. Balance the machine by adjusting
the feet.
Rotate the feet to adjust until the machine
stands level and firmly.
CNever unscrew the adjustable feet from
their housings.
Electrical connection
Connect the machine to a grounded
outlet protected by a fuse of suitable
capacity as stated in the technical
specifications table. Our company shall
not be liable for any damages that will
arise when the machine is used on a
circuit without grounding.
• Connection must comply with national
regulations.
• If the current value of the fuse or
breaker in the house is less than 16
Amps, have a qualified electrician install
a 16 Amp fuse.
• Power cable plug must be within easy
reach after installation.
• The voltage and allowed fuse or
breaker protection are specified in the
“Technical Specifications” section.
• The specified voltage must be equal to
your mains voltage.
• Do not make connections via extension
cables or multi-plugs.
• The main fuse and switches must have
a contact distance of minimum 3 mm.
BDamaged power cable must only be
replaced by a qualified electrician.
BIf the product is faulty, it must not be
operated unless it is repaired! There is
the risk of electric shock!
First use
• To have the product ready for operation
before calling the authorised service
agent, make sure that its location
and power supply installations are
appropriate. If they are not, call a
qualified electrician to have any
necessary arrangements carried out.
• Make sure that the power connections
of the product are in accordance
with the instructions given in relevant
chapters of this manual.
Disposing of packaging mate-
rial
Packaging materials are dangerous to
children. Keep packaging materials in
a safe place out of reach of children.
Packaging materials of your product are
manufactured from recyclable materials.
Sort and dispose of them in accordance
with recycled waste instructions. Do not
dispose of them with normal domestic
waste.
Transportation of the machine
1. Unplug the machine from the mains.
2. Remove the water drain (if any) and
chimney connections.
3. Drain water remained in the machine
completely before transportation.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how
to dispose of your machine.
Before disposing of your old machine,
cut off the power cable plug and make
the loading door lock unusable to avoid
dangerous conditions to children.

7EN
3Initial preparations for drying
Things to be done for energy saving:
• Make sure that you operate the product
at its full capacity but pay attention to
not exceeding it.
• Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
• Pay attention to dry same types of
laundry together.
• Follow the instructions in the user
manual for programme selection.
• Make sure that sufficient clearance is
provided at the front and rear side of the
dryer for air circulation. Do not block the
grill at the front side of the product.
• Do not open the door of the machine
during drying unless necessary. If you
must certainly open the door, pay
attention not to keep it open for a long
time.
• Do not add new (wet) laundry during
drying.
• Lint and fibres released from the laundry
to the air during the drying cycle are
collected in the “Lint Filter”. Make sure
that you clean the filters before or after
each drying.
• In models with condenser, make sure
that you clean the condenser regularly
at least once every month or after every
30 drying cycles.
• In vented models, follow the chimney
connection rules in the user manual and
pay attention to the chimney cleaning.
• Ventilate the room, where the dryer is
located, well during drying.
• For power saving in models with
lamps, at times when your dryer is not
in use, keep the door closed if the On/
Off button is pressed (if the dryer is
energized).
Laundry suitable for drying in the
machine
CAlways follow the suggestions on the
laundry labels. Dry only the laundry
having a label stating that they are
suitable for drying in a dryer and make
sure that you select the appropriate
programme.
A B C
l mn
o p q
D
Low
Laundry unsuitable for drying in the
machine
• Laundry items with metal attachments
such as belt buckles and metal buttons
can damage your dryer.
• Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping
bags in the dryer.
• Laundry made of delicate and valuable
fabrics as well as lace curtains can be
creased. Do not dry them in the dryer!
• Do not dry items made of hermetic
fibres such as pillows and quilts in the
dryer.
• Laundry made of foam or rubber will be
deformed.
• Do not dry laundry containing rubber in
the dryer.
• Do not dry laundry exposed to
petroleum, oil, combustible or explosive
agents in the dryer even if they are
washed beforehand.
• Overly wet laundry or laundry with
dripping water must not be put into the
dryer.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should
not be dried in the product since they
emit flammable or explosive vapor.
• Do not dry items cleaned with industrial
chemicals in the dryer.

8EN
• Do not dry your unwashed laundry in
the dryer.
• Items soiled with cooking oils,
acetone, alcohol, fuel oil, kerosene,
stain remover, turpentine, paraffin and
paraffin removers must be washed
in hot water with plenty of detergent
before being dried in the dryer.
• Garments or pillows bolstered with
rubber foam (latex foam), shower
bonnets, water resistant textiles,
materials with rubber reinforcement
and rubber foam pads should not be
dried in the dryer.
• Do not use fabric softeners and
anti-static products unless they are
recommended by the manufacturers of
the fabric softener or the product.
• Do not dry the underwear reinforced
with metal parts in the dryer. If these
metal reinforcements loosen and break
during drying, they will damage your
dryer.
Preparing laundry for drying
• Check all laundry items before loading
them into the product to make sure that
there are no lighters, coins, metal items,
needles and etc. in their pockets or on
any part of them.
• Fabric softeners and similar products
must be used in accordance with the
instructions of the manufacturer of the
relevant products.
• All laundry must be spun at the highest
spin speed that your washing machine
allows for the laundry type.
• Laundry may be tangled after washing.
Separate your laundry before placing
them into your dryer.
• Sort your laundry according to their
types and thicknesses. Dry the same
type of laundry together. E.g.: fine
kitchen towels and table cloths dry
faster than the thick bath towels.
Correct load capacity
AConsider the information in the
"Programme Selection Table". Always
start the programme in accordance with
the maximum load capacity.
CAdding laundry to the machine more
than the level shown in the figure is not
recommended. Drying performance
will degrade when the machine is
overloaded. Furthermore, your dryer
and your laundry can be damaged.
C Place your laundry into the drum loosely
so that they will not get tangled.
CLarge pieces (E.g.: bed sheets, quilt
covers, large tablecloths) may bunch-
up. Stop the dryer 1-2 times during
drying process to separate bunched-up
laundry.
Following weights are given as examples.
Home articles Approximate
weights (g)
Cotton quit covers (double) 1500
Cotton quit covers (single) 1000
Bed sheets (double) 500
Bed sheets (single) 350
Large tablecloths 700
Small tablecloths 250
Tea napkins 100
Bath towels 700
Hand towels 350
Garments Approximate
weights (g)
Blouses 150
Cotton shirts 300
Shirts 200
Cotton dresses 500
Dresses 350
Jeans 700
Handkerchiefs (10 pieces) 100
T-Shirts 125
Loading
• Open the loading door.
• Place laundry items loosely into the
dryer.
• Push the loading door to close. Ensure
that no items are caught in the door.

9EN
4Selecting a Programme and Operating Your Machine
Control panel
1. Filter cleaning warning light
Warning light turns on when the filter is
full.
2. Program follow-up indicator
Used to follow-up the progress of the
current programme.
3. Cancel audio warning
Used to cancel the audio warning given
at the end of the programme.
4. On/Off button
Used to turn on and off the machine.
5. Programme selection knob
Used to select a programme.
6. Start/Pause/Cancel button
Used to start, pause or cancel the
programme.
7. Water tank warning light*
Warning light turns on when the water
tank is full.
8.Time delay selection button*
Used to set the time delay.
* It may change according to the
specifications of your dryer
1 2 3 4
67 5

10 EN
Preparing the machine
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the “On/Off” button.
C Pressing the “On/Off” button does not
necessarily mean that the programme
has started. Press “Start/Pause/Cancel”
button of the machine to start the
programme.
Programme selection
Decide the appropriate programme from
the table below which includes drying
temperatures in degrees. Select the desired
programme with the programme selection
button.
Extra dry
Dry at high temperature
only for cotton laundry.
Thick and multi layered
laundry (E.g.: towels,
linens, jeans) are dried in
a way that they do not
require ironing before
placing in the wardrobe.
Ready to
wear
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do
not require ironing before
placing in the drawers.
Ready to
wearPlus
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do
not require ironing before
placing in the drawers,
but more than those in the
ready to wearoption.
Iron Dry
Normal laundry (E.g.,
Shirts, dresses) are dried
ready to be ironed.
C For further program details, see,
“Program Selection Table”
Main programmes
Depending on the type of laundry, the
following main programmes are available:
•Cottons
You can dry your durable laundry with this
programme. Dries at high temperature. It
is recommended to use for your cotton
items (such as bed sheets, quilt cover,
underclothing, etc.).
•Synthetics
You can dry your less durable laundry
with this programme. It dries at a lower
temperature compared to the cottons
programme. It is recommended for your
synthetic laundry (such as shirts, blouses,
synthetic/cotton blended laundry, etc.).
C Do not dry curtains and lace in your
machine.
•Anti-creasing
A 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry
out after the programme is over. This
programme rotates the laundry in
10-minute intervals to prevent creasing.
Special programmes
For special cases, there are also extra
programmes available:
CAdditional programmes may differ
according to the model of your machine.
•Xpress 35
You can use this programme to dry the
cottons that are spun at high speeds in
your washing machine. It can dry your 1,25
kg Cotton laundry (3 Shirts / 3 T-Shirts)
within 35 minutes.
C In order to obtain better results from the
dryer programs, your laundry must be
washed with suitable program and spun
at the recommended spin speeds in your
washing machine.
•Shirts
Dries the shirts in a more sensitive way so
that they are less creased and ironed easily.
CShirts may contain little amount of
dampness at the and of the program. It
is advised not to leave the shirts in the
dryer.
•Jeans
You can use this program to dry the jeans
that are spun at high speeds in your
washing machine.
C Review the relevant part of the program
table.
•Delicates
You can dry at a lower temperature your
very delicate laundry (silk blouses, fine
underwear, etc.) that are suitable for drying
or laundry which is advised to be hand-
washed.
C It is recommended to use a cloth bag
to avoid certain delicate garments
and laundry from getting creased
or damaged. Take your garments

11 EN
immediately out of the dryer and hang
them after the programme ends in
order to prevent them being creased.
•Ventilation
Only ventilation is performed for 10
minutes without blowing hot air. You
can air your clothes that have been kept
at closed environments for a long time
thanks to this program to deodorize
unpleasant odors.
•Timer programs
You can select one of the 10 min.,
20 min., 40 min. and 60 min. timer
programmes to achieve the desired
final drying level at low temperatures.
Programme dries at the selected time
regardless of the drying temperature.

12 EN
* : Energy Label standard program (EN 61121:2005)
All values given in the table have been fixed according to EN 61121:2005 Standard.
These values may deviate from the table according to the laundry type, laundry spin
speed, environmental conditions and voltage fluctuations.
Program selection and consumption table
EN
Programs Capacity (kg)
Spin speed
in washing
machine (rpm)
Approximate
amount of
remaining
humidity
Drying time
(minutes)
Cottons / Coloreds
AReady to Wear 7 1000 % 60 135
AReady to Wear + 7 1000 % 60 142
AReady to Iron 7 1000 % 60 110
Xpress 35’ 1.25 1400 %50 35
Shirt 1.5 1000 %50 40
Jeans 4 1200-1000 %50 85
Delicates 1.75 800 %40 40
Synthetics
BReady to Wear 3.5 800 % 40 53
Energy consumption values
Programs Capacity (kg)
Spin speed
in washing
machine (rpm)
Approximate
amount of
remaining
humidity
Energy
consumption
value kWh
Cottons linen Ready to wear* 7 1000 % 60 4.35
Cottons Ready to iron 7 1000 % 60 3.45
Synthetics Ready to wear 3.5 800 % 40 1.60

13 EN
EN
Programs Capacity (kg)
Spin speed
in washing
machine (rpm)
Approximate
amount of
remaining
humidity
Drying time
(minutes)
Cottons / Coloreds
AReady to Wear 7 1000 % 60 135
AReady to Wear + 7 1000 % 60 142
AReady to Iron 7 1000 % 60 110
Xpress 35’ 1.25 1400 %50 35
Shirt 1.5 1000 %50 40
Jeans 4 1200-1000 %50 85
Delicates 1.75 800 %40 40
Synthetics
BReady to Wear 3.5 800 % 40 53
Energy consumption values
Programs Capacity (kg)
Spin speed
in washing
machine (rpm)
Approximate
amount of
remaining
humidity
Energy
consumption
value kWh
Cottons linen Ready to wear* 7 1000 % 60 4.35
Cottons Ready to iron 7 1000 % 60 3.45
Synthetics Ready to wear 3.5 800 % 40 1.60
Auxiliary function
Cancel audio warning
Your dryer will give an audio warning when
the programme comes to an end. If you
do not want to hear the audio warning,
press “Cancel Audio Warning” button. The
relevant light will turn on when this button
is pressed and an audio warning will not be
given when the programme comes to an
end.
CYou can select this function either before
or after the programme starts.
Warning indicators
CWarning indicators may differ according
to the model of your dryer.
Filter cleaning
A warning light will turn on to remind filter
cleaning after the programme finishes.
CIf the filter cleaning warning light lights up
continuously, please refer to, “Suggested
solutions for problems”.
Water tank
Warning light starts flashing when the
tank is filled with water. The dryer stops
operating if the warning light turns on when
a programme is running. Drain the water
in the water tank to restart the dryer. Press
“Start/Pause/Cancel” button to start the
programme after you have emptied the
water tank. The warning light turns off and
the programme resumes operating.
Starting the programme
1. Press “Start/Pause/Cancel” button to
start the programme.
2. Light of the “Start/Pause/Cancel”
button will turn on to indicate that the
programme has started.
Progress of program
Progress of a running program is shown
through the program follow-up indicator.
At the beginning of every program step, the
relevant indicator LED will light up and light
of the completed step will turn off.
“Drying”:
- Drying level will be illuminated during
the whole drying process until the drying
degree reaches “iron dry”.
“Iron Dry”:
- Starts to illuminate when the drying
degree reaches “iron dry” step and remains
illuminated until the next step.
“Ready to wear”:
Starts to illuminate when the drying degree
reaches “Ready to wear” step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the program comes
to an end and anti-creasing function is
activated.
C If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the programme after it has
started
You can use this feature to dry your clothes
under higher or lower temperatures after
your dryer has started.
For example;
1. Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
2. Select the “Extra Dry” programme by
rotating the programme selection button.
3. Press “Start/Pause/Cancel” button to
start the programme.
CPress “Start/Pause/Cancel” button for
3 seconds to cancel the programme or
turn the programme selection knob in
any direction to end the programme while
the machine is running. Water tank and
filter cleaning warning lights turn on to
warn the user when the programme is
cancelled by pressing the “Start/Pause/
Cancel” button for 3 seconds. However,
the warning lights do not turn on when
the programme is cancelled by turning
the programme selection knob. Only the
drying light turns on and the machine
remains in hold until a new programme
is selected and the “Start/Pause/Cancel”
button is pressed. Child-proof lock of the
machine should not be active in order
to perform these two operations. If the
child-proof lock is active, deactivate it
before performing these operations.
Adding/removing laundry in standby mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button to
switch the dryer to “Pause” mode. Drying
process will stop.
2. Open the door at “Pause” position and
close it again after adding or taking out
laundry.
3. Press “Start/Pause/Cancel” button to

14 EN
start the programme.
CAny laundry added after the drying
process has started may cause the dried
clothes in the machine intermingle with
wet clothes and the result will be wet
laundry after the drying process is over.
CLaundry may be added or taken out
as much as desired during a drying
process, but this process will extend the
programme duration and increase energy
consumption since the drying will be
interrupted continuously. Therefore, it is
recommended to add laundry before the
drying programme has started.
Child-proof lock
There is a child-proof lock to prevent any
programme interruption due to the pressing
of button while the programme is running.
The loading door and all buttons except
the “On/Off” button on the control panel
are deactivated when the child-proof lock is
active.
Press the “Start/Pause/Cancel” and
“Cancel audio warning” buttons
simultaneously for 3 seconds to activate the
child-press lock.
To start a new programme after the
programme is over or to interrupt the
programme, the child-proof lock should be
deactivated. Press the same buttons for
3 sec. again to deactivate the child-proof
lock.
CChild-proof lock is deactivated when the
machine is restarted by pressing the On/
Off button.
C Press the relevant buttons for 3 seconds
to activate the child-proof lock. A long
beep will be heard and the child-proof
lock will be activated. A double beep
will be heard if you press any button
or turn the programme selection knob
while the child-proof lock is active. Press
the buttons for 3 seconds to deactivate
the child-proof lock. Single beep will
be heard and child-proof lock will be
deactivated.
AA double beep will be heard if you turn
the programme selection knob when the
machine is running and the child-proof
lock is active. If you deactivate the child-
proof lock without returning the program
selection knob to its previous position,
the programme will be terminated since
the position of the programme selection
knob is changed. The drying light turns
on and the machine remains on hold until
a new programme is selected and the
“Start/Pause/Cancel” button is pressed.
Finishing by canceling the programme
To cancel any selected programme:
Press “Start/Pause/Cancel” button for
about 3 seconds. The “Filter cleaning”,
“Water tank” and “End/ Anti-creasing”
warning lights will turn on at the end of this
period for reminding purposes.
AAs the inside of the dryer will be
excessively hot when you cancel the
programme while the dryer is running,
activate the ventilation programme to
cool it down.
End of programme
The “End/Anti-creasing”, “Filter cleaning”
and “Water tank” warning lights on the
programme follow up indicator will turn on
when the programme comes to an end.
The door can be opened and the machine
becomes ready for a second cycle.
Press “On/Off” button to turn off the dryer.
CFinal step of the drying cycle (cooling
step) is performed without heat
application in order to keep the items at a
temperature that would not harm them.
CA 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry
out after the programme has come to an
end.
CIf you will not take the laundry out
immediately, do not stop the dryer before
the drying process is complete.
CClean the filter after each drying (please
see, Filter cleaning).
CDrain the water tank after each drying
(please see, Water tank)

15 EN
EN 2
Height (adjustable) 84.6 cm
Width 59.5 cm
Depth 53 cm
Capacity (max.) 7 kg
Weight (net) 35 kg
Voltage
See type labelRated power input
Model code
Type label is located behind the loading door.
Technical Specification

16 EN
There are humidity sensors in your dryer
that detect whether the laundry is dry or
not.
To clean the sensor:
1. Open the loading door of the dryer.
2. Allow the machine to cool down if drying
has been carried out.
3. Wipe the metal sensors with a soft
cloth, dampened with vinegar and dry
them.
CClean metal sensors 4 times a year.
ANever use solvents, cleaning agents
or similar substances when cleaning
since these materials can cause fire and
explosion!
Water tank;
The moisture in the damp laundry is taken
from the laundry and condens ed. Drain
the water tank after each drying cycle or
during drying when “Water tank” warning
light turns on.
ACondensed water is not drinkable!
ANever take out the water tank when the
programme is running!
- Inside the drawer on the panel
- Behind the kick plate cover
If you forget to drain the water tank, your
dryer will stop during the following drying
cycles when the water tank is full and the
“Water tank” warning light will turn on. If
this is the case, press the “Start/Pause/
Cancel” button to resume the drying cycle
after draining the water tank.
To drain the water tank:
1-Carefully remove the water tank by
opening the kick plate cover/pulling the
drawer.
5Maintenance and cleaning
Filter Cartridge / Door Inner Surface
Lint and fibres released from the laundry to
the air during the drying cycle are collected
in the “Filter Cartridge”.
CSuch fibre and lint are generally
formed during wearing and washing.
CAlways clean the filter and the
inner surfaces of the cover after each
drying process.
CYou can clean the filter and filter
area by vacuum cleaner.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up
and open the filter.
3. Clean lint, fibre, and cotton raveling by
hand or with a soft piece of cloth.
4. Close the filter and place it back into its
seat.
C Clogging may arise on the filter surface
after using your machine for some time;
if this occurs, wash the filter with water
and dry it before using again.
C Clean the entire inner surface of the
cover and door gasket.
Sensor

17 EN
2-Drain the water in the tank
3-If there is lint accumulation in the funnel
of the water tank, clean it under running
water.
4-Place the water tank into its seat.
For the condenser;
Hot and humid air in the condenser is
cooled with the cold air from the room.
Thus, the humid air circulating in your
dryer is condensed and then pumped
into the tank.
CClean the condenser after every 30
drying cycles or once a month.
To clean the condenser:
1. If a drying process has been carried
out, open the door of the machine and
wait until it cools down.
2. Unlock the 2 condenser locks after
opening the kick plate.
3. Pull out the condenser.
4. Clean the condenser by applying
pressurized water with a shower
armature and wait until the water
drains.
5. Place the condenser in its housing.
Fasten the 2 locks and make sure that
they are seated securely.
6. Close the kick plate cover.

18 EN
6Suggested solutions for problems
Drying process takes too much time
• Meshes of the filter may be clogged. Wash with water
Laundry comes out wet at the end of drying.
• Meshes of the filter may be clogged. Wash with water.
• Excessive laundry might have been loaded in. Do not load the dryer in excess.
Dryer does not switch on or the programme does not start. Dryer is not activated
when set.
• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Programme might have not been set or the «Start/Pause/Cancel» button might
have not been pressed. Make sure that the programme has been set and it is not
in “Pause” mode.
• «Childproof lock» might have been activated. Deactivate the childproof lock.
Programme has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press «Start/Pause/Cancel» button to start the
programme.
• Water may be full. Drain the water in the tank.
Laundry has shrunk, become felted or deteriorated.
• A programme suitable for the laundry type might have not been used. Dry only
the laundry which is suitable for drying in dryer after checking the labels on your
clothes.
• Select a programme with suitable low temperature for the laundry type to dry your
clothes.
Drum lightning does not come on. (For models with lamp)
• Dryer might have not been started by using the «On/Off» button. Make sure that
the dryer is on.
• Bulb may have blown. Call the authorized service to replace the bulb.
“Final / Anti-creasing” LED flashes.
• The 2-hour anti creasing programme to prevent laundry from creasing might have
been activated. Turn off the dryer and take out the laundry.
“Final / Anti-creasing” LED is on.
• Programme has come to an end. Turn off the dryer and take out the laundry.
The “Drying” LED flashes.
• A heat sensor failure has occurred. Dryer ends the programme without heating.
Turn off the dryer and take out the laundry. Call your authorized service
“Filter cleaning” LED is on.
• Filter might have not been cleaned. Clean the cover filter.
“Water comes out the cover”
• Clean the entire inner surface of the cover and door gasket.
“Cover opens spontaneously.”

19 EN
• Push it until you hear that it is closed.
For products with a condenser:
“Water tank” warning LED is on.
• Water may be full. Drain the water in the tank.
“Condenser cleaning” LED is on.
• Condenser might have not been cleaned. Clean the filters in the condenser under
the kick plate.
A Call an authorized service if the problem persists.

初次操作本产品前，请阅读该手册！
亲爱的顾客，
我们的产品使用先进设备生产，并通过严格的质量控制检测，希望您能从中获取最大的效益。
我们建议您在使用本产品前仔细阅读本手册，并妥善保管，以备日后参考。
本《用户手册》将
• 帮助您快速、安全地使用本设备。
• 安装和起动本产品前，阅读《用户手册》。
• 尤其注意遵守与安全有关的说明。
• 将本《用户手册》置于触手可及之处，以备日后参考。
• 请阅读本产品附带的所有其它文件。
请注意，本《用户手册》也适用于某些其它型号。
符号解释
本《用户手册》中，使用了下列符号：
A 重要安全信息。警告有關生命和財產安全的危險情況。
B 小心：警告電源電壓。
小心：警告火災危險。
小心：警告熾熱表面。
閱讀說明書。
C 有用信息。有關應用的重要信息或有用的提示。
本机的包装材料是可回收的。将它丢弃到专门的回收站有助于回收该材料并保护
环境。同时，您的 机器中也有多个可回收部件。它们上面均有如图所示的标签标
明。请不要将这些部件与普通垃圾一 同处理。这样制造商才能最好地按照欧洲废
电子电气处理标准2002/96/EC来处理这些部件。联系您 所在地区的市政府或零售商
获得离您家最近的回收站地址。我们感谢您为保护环境所作的工作。
2960310397_ZH/040211.1749