Beko WRE 7512 XWW User manual

2820670914_В
Washing Machine
Pesumasin
Kasutusjuhend
Veļas mazgājamā mašīna
Letošanas rokasgrāmata
Skalbimo mašina
Vartotojo vadovas
Automatická pračka
Používateľská príručka
Plně automatická pračka
Návod k používání
WRE 7512 XWW
EN ET LV LT CZ SK

3/ EN Washing Machine / User’s Manual
1 Important nstructons for safety and envronment
This section contains safety instructions that will help protect from risk of personal injury or proper-
ty damage. Failure to follow these instructions shall void any warranty.
1.1 General safety
• This product can be used by children at and above 8 years old and by persons whose physical,
sensory or mental capabilities were not fully developed or who lack experience and knowledge
provided that they are supervised or trained on the safe usage of the product and the risks it
brings out. Children must not play with the product. Cleaning and maintenance works should not
be performed by children unless they are supervised by someone.
• Children of less than 3 years should be kept away unless continuously supervised.
• Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machi-
ne will cause electrical parts to overheat. This will cause problems with your product.
• If the product has a failure, it should not be operated unless it is repaired by the Authorized
Service Agent. There is the risk of electric shock!
• This product is designed to resume operating in the event of powering on after a power interrup-
tion. If you wish to cancel the programme, see "Cancelling the programme" section.
• Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the
grounding installation made by a qualified electrician. Our company shall not be liable for any
damages that will arise when the product is used without grounding in accordance with the local
regulations.
• The water supply and draining hoses must be securely fastened and remain undamaged.
Otherwise, there is the risk of water leakage.
• Never open the loading door or remove the filter while there is still water in the drum. Otherwise,
risk of flooding and injury from hot water will occur.
• Do not force open the locked loading door. The loading door will be ready to open just a few
minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the
door and the lock mechanism may get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
• Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by
grabbing the plug.
• Use detergents, softeners and supplements suitable for automatic washing machines only.
• Follow the instructions on the textile tags and on the detergent package.
• The product must be unplugged during installation, maintenance, cleaning and repairing proce-
dures.
• Always have the installation and repairing procedures carried out by the Authorized Service
Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried
out by unauthorized persons.
• If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a
similarly qualified person (preferably an electrician) or someone designated by the importer in
order to avoid possible risks.
• Place the product on a rigid, flat and level surface.
• Do not place it on a long-pile rug or similar surfaces.
• Do not place the product on a high platform or near the edge on a cascaded surface.
• Do not place the product on the power cable.
• Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic
surfaces.
1.2 Intended use
• This product has been designed for domestic use. It is not suitable for commercial use and it must
not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or transportation.
1.3 Chldren's safety
• Packaging materials are dangerous to children. Keep packaging materials in a safe place away
from reach of the children.
• Electrical products are dangerous for the children. Keep children away from the product when it is
in use. Do not let them to tamper with the product. Use child lock to prevent children from inter-
vening with the product.
• Do not forget to close the loading door when leaving the room where the product is located.

4/ EN Washing Machine / User’s Manual
• Store all detergents and additives in a safe place away from the reach of the children by closing
the cover of the detergent container or sealing the detergent package.
While washing the laundry at high temperatures, the loading door glass becomes
hot. Therefore, keep especially the children away from the loading door of the
machine while the washing operation is in progress.
1.4 Package nformaton
• Packaging materials of the product are manufactured from recyclable materials in accordance
with our National Environment Regulations. Do not dispose of the packaging materials together
with the domestic or other wastes. Take them to the packaging material collection points desig-
nated by the local authorities.
1.5 Dsposng of the waste product
• This product has been manufactured with high quality parts and materials which can be reu-
sed and are suitable for recycling. Therefore, do not dispose the product with normal domestic
waste at the end of its service life. Take it to a collection point for the recycling of electrical and
electronic equipment. Please consult your local authorities to learn the nearest collection point.
Help protect the environment and natural resources by recycling used products. For children's
safety, cut the power cable and break the locking mechanism of the loading door so that it will be
non-functional before disposing of the product.
1.6 Complance wth WEEE Drectve
This product complies with EU WEEE Directive (2012/19/EU). This product bears a classifi-
cation symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be
reused and are suitable for recycling. Do not dispose of the waste product with normal
domestic and other wastes at the end of its service life. Take it to the collection center for
the recycling of electrical and electronic equipment. Please consult your local authorities
to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not con-
tain harmful and prohibited materials specified in the Directive.
2 Installation
Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready
for use, review the information in the user manual and make sure that the electricity, tap water supply and
water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a
qualified technician and plumber to have any necessary arrangements carried out.
CPreparation of the location and electrical, tap water and waste water installations at the place of
installation is under customer's responsibility.
BWARNING: Installation and electrical connections of the product must be carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried
out by unauthorized persons.
AWARNING: Prior to installation, visually check if the product has any defects on it. If so, do not have it
installed. Damaged products cause risks for your safety.
CMake sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after installation or cleaning procedures.
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with full load- when they are placed on top of each
other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature may fall below 0°.
• Place the product at least 1 cm away from the edges of other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging
reinforcement by pulling the ribbon.

5/ EN Washing Machine / User’s Manual
2.3 Removing the transportation locks
AWARNING: Do not remove the transportation locks before taking out the packaging reinforcement.
AWARNING: Remove the transportation safety bolts before operating the washing machine! Otherwise,
the product will be damaged.
1. Loosen all the bolts with a suitable spanner until they rotate freely (C).
2. Remove transportation safety bolts by turning them gently.
3. Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)
CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved
again in the future.
CNever move the product without the transportation safety bolts properly fixed in place!
2.4 Connecting water supply
CThe water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary
to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run
smoothly. Attach a pressure reducing valve if water pressure is higher.
CIf you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the
supplied stopper to the hot water valve before operating the product. (Applies for the products supplied
with a blind stopper group.)
AWARNING: Models with a single water inlet should not be connected to the hot water tap. In such a case
the laundry will get damaged or the product will switch to protection mode and will not operate.
AWARNING: Do not use old or used water inlet hoses on the new product. It may cause stains on your
laundry.
1. Tighten all hose nuts by hand. Never use a tool when tightening
the nuts.
2. Open the taps completely after making the hose connection to
check for water leaks at the connection points. If any leaks occur,
turn off the tap and remove the nut. Retighten the nut carefully after
checking the seal. To prevent water leakages and damages caused
by them, keep the taps closed when the machine is not in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.
AWARNING: Your house will be flooded if the hose comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to
ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that
it cannot come out.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the heights
described in the figure.
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.

6/ EN Washing Machine / User’s Manual
• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched
between the drain and the machine.
• If the length of the hose is too short, use it by adding an original extension hose. Length of the hose
may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose
and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and
leak.
2.6 Adjusting the feet
A WARNING: In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance the machine by
adjusting the feet.
Otherwise, the product may move from its place and cause crushing and vibration
problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level and balanced.
3. Tighten all lock nuts again by hand.
AWARNING: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be liable for
any damages that will arise when the product is used without grounding in accordance with the local
regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after installation.
• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician
install a 16 Amp fuse.
• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.
• Do not make connections via extension cables or multi-plugs.
BWARNING: Damaged power cables must be replaced by the Authorized Service Agents.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply connections.
3. Drain all water that has remained in the product.
4. Install transportation safety bolts in the reverse order of removal procedure.
CNever move the product without the transportation safety bolts properly fixed in place!
AWARNING: Packaging materials are dangerous to children. Keep packaging materials in a safe place away
from reach of the children.
3 Preparation
3.1 Sorting the laundry
• Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.
• Always obey the instructions given on the garment tags.
3.2 Preparing laundry for washing
• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will
damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or
pillow case.

7/ EN Washing Machine / User’s Manual
• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and
brush. Such objects may damage the product or cause noise problem.
• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and tears.
• Wash“machine washable” or “hand washable” labeled products only with an appropriate programme.
• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale removers suitable for machine wash. Always follow the
instructions on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce
pilling.
• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken
off before placing into the machine. Such dusts and powders on the laundry may build up on the inner
parts of the machine in time and can cause damage.
3.3 Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by the programme you have selected, but do not
overload; see, "Programme and consumption table".
• Always follow the instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled laundry.
• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing
process.
• Do not use detergent in excess of the amount recommended on the detergent package.
3.4 Initial use
Before starting to use the product, make sure that all preparations are made
in accordance with the instructions in sections“Important safety instructions”
and“Installation”.
To prepare the product for washing laundry, perform first operation in Drum
Cleaning programme. If your product is not equipped with Drum Cleaning
programme, perform the Initial Use procedure in accordance with the
methods described under“5.2 Cleaning the loading door and the drum”
section of the user manual.
CUse an detergents suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is
not harmful for the product.
3.5 Correct load capacity
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing
programme desired.
The machine automatically adjusts the amount of water according to the weight of the loaded laundry.
Awarning:Follow the information in the“Programme and consumption table”. When overloaded, machine's
washing performance will drop. Moreover, noise and vibration problems may occur.
3.6 Loading the laundry
1. Open the loading door.
2. Place laundry items loosely into the machine.
3. Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.
CThe loading door is locked while a programme is running. The door can only be opened a while after the
programme comes to an end.
Awarning: In case of misplacing the laundry, noise and vibration problems may occur in the machine.

8/ EN Washing Machine / User’s Manual
3.7 Using detergent and softener
CWhen using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer's
instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available.
1
3
2
Detergent Drawer
The detergent drawer is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing programme.
• Never leave the detergent drawer open while the washing programme is running!
• When using a programme without prewash, do not put any detergent into the prewash compartment
(compartment nr. "1").
• In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment
nr. "1").
• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the
detergent bag or the dispensing ball directly among the laundry in the machine.
• If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash
compartment (compartment nr. "2").
Choosing the detergent type
The type of detergent to be used depends on the type and colour of the fabric.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely
for delicate clothes.
• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
• Wash woolens with special detergent made specifically for woolens.
A
warning: Use only detergents manufactured specifically for washing machines.
warning: Do not use soap powder.
Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and
water hardness.
• Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid
problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.
• Use lesser detergent for small amounts or lightly soiled clothes.
Using softeners
Pour the softener into the softener compartment of
the detergent drawer.
• Do not exceed the (>max<) level marking in the
softener compartment.
• If the softener has lost its fluidity, dilute it with
water before putting it in the detergent drawer.
Using liquid detergents
If the product contains a liquid detergent cup:
• Make sure that you have placed the liquid detergent cup in compartment nr.“2”.
• If the lqud detergent has lost ts fludty, dlute t wth water before puttng n the detergent cup.
2

9/ EN Washing Machine / User’s Manual
Lght colours and whtes Colours Dark colours Delcates/Woollens/
Slks
(Recommended
temperature range based
on soiling level: 40-90 °C)
(Recommended
temperature range based
on soiling level: cold
-40 °C)
(Recommended
temperature range
based on soiling
level: cold -40 °C)
(Recommended
temperature range
based on soiling level:
cold -30 °C)
Soiling Level
Heavly
Soled
(dffcult
stans such
as grass,
coffee, fruts
and blood.)
It may be necessary to
pre-treat the stains or
perform prewash. Powder
and liquid detergents
recommended for whites
can be used at dosages
recommended for
heavily soiled clothes. It
is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches.
Powder and
liquid detergents
recommended for
colours can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches.
Use detergents without
bleach.
Liquid detergents
suitable for
colours and dark
colours can be
used at dosages
recommended
for heavily soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woollen and silk
clothes must be
washed with special
woollen detergents.
Normally
Soled
(For
example,
stans
caused by
body on
collars and
cuffs)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
normally soiled clothes.
Powder and
liquid detergents
recommended for
colours can be used at
dosages recommended
for normally soiled
clothes. Use detergents
without bleach.
Liquid detergents
suitable for
colours and dark
colours can be
used at dosages
recommended for
normally soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woollen and silk
clothes must be
washed with special
woollen detergents.
Lghtly
Soled
(No vsble
stans exst.)
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended for
lightly soiled clothes.
Powder and
liquid detergents
recommended for
colours can be used at
dosages recommended
for lightly soiled clothes.
Use detergents without
bleach.
Liquid detergents
suitable for
colours and dark
colours can be
used at dosages
recommended
for lightly soiled
clothes.
Prefer liquid
detergents produced
for delicate clothes.
Woollen and silk
clothes must be
washed with special
woollen detergents.
When you want to use lqud detergent, pull the
apparatus towards yourself. The part that falls down wll
serve as a barrer for the lqud detergent. If requred,
clean the apparatus wth water when t s n place or
by removng t. If you wll use powder detergent, the
apparatus must be secured at top poston.
When you want to use lqud detergent, pull the
apparatus towards yourself. The part that falls down wll
serve as a barrer for the lqud detergent. If requred,
clean the apparatus wth water when t s n place or
by removng t. If you wll use powder detergent, the
apparatus must be secured at top poston.

10 / EN Washing Machine / User’s Manual
If the product does not contain a liquid detergent cup:
• Do not use liquid detergent for the prewash in a programme with prewash.
• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use
the Delayed Start function, do not use liquid detergent.
Using gel and tablet detergent
Apply the following instructions when using tablet, gel and similar detergents.
• If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent
cup, put the gel detergent into the main wash detergent compartment during first water intake.
If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the
programme.
• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into
the drum before washing.
• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the
drum before washing.
CTablet detergents may leave residues in the detergent compartment. If you encounter such a case, place
the tablet detergent between the laundry, close to the lower part of the drum in future washings.
Use the tablet or gel detergent without selecting the prewash function.
Using starch
• Add liquid starch, powder starch or the fabric dye into the softener compartment.
• Do not use softener and starch together in a washing cycle.
• Wipe the inside of the machine with a damp and clean cloth after using starch.
Using bleaches
• Select a programme with prewash and add the bleaching agent at the beginning of the prewash.
Do not put detergent in the prewash compartment. As an alternative application, select a
programme with extra rinse and add the bleaching agent while the machine is taking water from
the detergent compartment during first rinsing step.
• Do not use bleaching agent and detergent by mixing them.
• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes
skin irritation. Do not pour the bleaching agent onto the clothes and do not use it for coloured
clothes.
• When using oxygen based bleaches, select a programme that washes at a lower temperature.
• Oxygen based bleaches can be used together with detergents; however, if its thickness is not the
same with the detergent, put the detergent first into the compartment nr. "2" in the detergent
drawer and wait until the detergent flows while the machine is taking in water. Add the bleaching
agent from the same compartment while the machine is still taking in water.

11 / EN Washing Machine / User’s Manual
4.3 Operating the product
4.3.1 Control panel
1 - Programme Selection Knob (Uppermost position On / Off)
2 - Display
3 - End Time Adjustment Button
4 - Programme Follow-up Indicator
5 - Start/Pause Button
6 - Auxiliary Function Button 3
7 - Auxiliary Function Button 2
8 - Auxiliary Function Button 1
9 - Spin Speed Adjustment Button
10 - Temperature Adjustment Button
4.3.2 Preparng the machne
1. Make sure that the hoses are connected tightly.
2. Plug in your machine.
3. Turn the tap on completely.
4. Place the laundry in the machine.
5. Add detergent and fabric softener.
4.3.3 Programme selecton and tps for effcent washng
1. Select the programme suitable for the type, quantity and soiling degree of the laundry in
accordance with the "Programme and consumption table" and the temperature table below.
2. Use the Programme Selection knob to select the desired programme.

12 / EN Washing Machine / User’s Manual
4.3.4 Programme and consumpton table
• : Selectable
* : Automatically selected, cannot be cancelled.
** : Classic( ) is the test programme in accordance with EN 60456:2016 and energy label with
Commission Delegated Regulation (EU) 1061/2010)
***: Eco 40-60 with 40 °C temperature selection is the test programme in accordance with
EN 60456:2016/prA:2019 and energy label with Commission Delegated Regulation (EU)
2019/2014
- : See the programme description for maximum load.
Auxiliary
functions
Programme °C
Maximum load (kg) Water consumption (l) Power consuption (kVt/h) Spin speed Prewash Quicl Wash Extra rinsing
Temperature °C
Cottons
90 7 92 2.25 1000 • • • 90
60 7 92 1.70 1000 • • • 90
40 7 89 1.05 1000 • • • 90
Eco 40-60
7 52.0 1.045 1000 40-60
3.5 43.0 0.750 1000 40-60
2 38.0 0.440 1000 40-60
Classic
7 49.0 0.910 1000 40-60
3.5 42.5 0.600 1000 40-60
3.5 41.5 0.695 1000 40-60
Synthetics 60 3 65 1.20 1000 • • • 60
40 3 63 0.75 1000 • • • 60
Xpress / Super Xpress
90 7 62 2.00 1000 • 90
60 762 1.10 1000 • 90
30 760 0.20 1000 • 90
Xpress / Super Xpress
Fast+ 30 241 0.150 1000 •30
Mix 40 40 3 65 0.75 800 • • 40
Woollens 40 1.5 55 0.55 1000 • 40
Delicates 30 3 51 0.65 800 40
Down Wear 60 1.5 70 1.25 1000 • 60
Sports 40 3 44 0.45 1000 • 40
Dark Wash 40 2.5 82 0.85 1000 • 40
Lingerie 30 1 65 0.30 600 30
Shirts 60 3 55 1.20 800 • • 60
Hygiene 90 7 119 2.40 1000 90 - 20
Drum Clean 90 - 73 2.100 600 90
40***
40**,40***
40***
60**
60**
40**

13 / EN Washing Machine / User’s Manual
C
INFORMATION
• Water and power consumption may vary subject to the changes in water pressure, water hardness
and water temperature, ambient temperature, type and amount of laundry, selection of auxiliary
functions and spin speed, and changes in the mains voltage.
• When selecting a programme, you can see the washing duration on the display of your machine.
Depending on the amount of laundry you have loaded into the machine, there might be a
difference of 1 to 1.5 hours between the duration shown on the display and the actual duration
of the washing programme. The duration will be corrected automatically right after the washing
programme has started.
• The auxiliary functions in the table may vary according to the model of your machine.
• Auxiliary function selection modes can be changed by the manufacturing company. Existing
selection modes can be removed or new selection modes can be added.
• Always select the lowest appropriate temperature. The most efficient programmes in terms of
energy consumption are generally those that perform at lower temperatures and longer duration.
• Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning
speed in the spinning phase, the higher the noise and the lower the remaining moisture content.
4.3.5 Man programmes
Depending on the type of fabric, use the following main programmes.
• Cotone (Cottons)
You can wash your durable cotton laundry (sheets, bedlinen, towels, bathrobes, underwear
etc.) in this programme. When you press the quick wash function key, programme duration
becomes notably shorter but effective washing is ensured thanks to intense washing
movements. If the quick wash function is not selected, superior washing and rinsing
performance is ensured for your heavily soiled laundry.
• Sintetici (Synthetics)
You can use this programme to wash t-shirts, synthetic/cotton mix fabrics etc. Programme duration
is notably shorter and efficient washing performance is ensured. If the quick wash function is not
selected, superior washing and rinsing performance is ensured for your heavily soiled laundry.
• Lana / Lavaggio a Mano
(Woollens / Hand Wash)
Use this programme to wash your woollen/delicate clothes. Select the appropriate temperature
complying with the tag of your clothes. Your laundry will be washed with very delicate movements to
avoid any damage.
4.3.6 Addtonal programmes
For special cases, additional programmes are available in the machine.
C
INFORMATION
• Additional programmes may differ according to the model of the machine.
• Eco 40-60
The eco 40-60 programme is able to clean normally soiled cotton laundry declared to be
washable at 40 °C or 60 °C, together in the same cycle, and that this programme is used to
assess the compliance with the EU ecodesign legislation.
Although it washes longer than all other programmes, it provides high energy and water
savings. Actual water temperature may be different from the stated wash temperature. When
you load the machine with less laundry (e.g. ½ capacity or less), periods in programme stages
may automatically get shorter. In this case, energy and water consumption will decrease.

14 / EN Washing Machine / User’s Manual
• Hygiene+
Use this programme for laundry that requires an intense, long, anti-allergic and hygienic washing
cycle at high temperature. A high level of hygiene is ensured thanks to the long heating and additional
rinsing step.
• The programme was tested by the "VDE" institute while the temperature was 20°C, and its efficiency
in bacteria and mould elimination was certified.
• The programme has been tested by “The British Allergy Foundation - Allergy UK” while the
temperature was 60°C, and its efficiency in eliminating bacteria and mould, as well as allergens,
was certified.
• Delicati (Delicates)
You can use this programme to wash delicate laundry such as cotton/synthetic mix knitted
clothes or socks. Washing movements in this programme are more delicate. Set the temperature
to 20 degrees or use the Cold Wash option for clothes whose colour you wish to preserve.
• Xpress / Super Xpress
Use this programme to wash your lightly soiled cotton clothes in a short time. The
programme duration can be reduced down to 14 minutes when the quick wash function is
selected. When the quick wash function is selected, maximum 2 (two) kg of laundry must
be washed.
• Capi Scuri / Jeans ( Dark Care / Jeans)
Use this programme to preserve the colour of your dark-coloured clothes and jeans. This
programme provides high efficiency in washing, thanks to a special drum movement,
even at low temperatures. It is recommended to use liquid detergent or woollen shampoo
for dark coloured laundry. Do not wash your delicate clothes that contain wool etc. in this
programme.
• Mix 40
You can use this programme to wash cottons and synthetics together without the need to sort
them.
• Camicie (Shirts)
Use this programme to wash shirts made of cotton, synthetic and synthetic blended fabrics
together. This programme ensures that your clothes wrinkle less. When the quick wash function
is selected, the Pre-treatment algorithm is used.
• Apply the pre-treatment chemical directly onto the clothes, or add it together with the detergent
when the machine starts to take in water from the main wash compartment. This way, it will take
you much shorter to get the performance you would normally get with a regular washing cycle.
Life of your shirts will be longer.
• Outdoor / Sport
Use this programme to wash outdoor/sports clothes that contain cotton/synthetic mix, as well
as waterproof cloths like gore-tex. This programme washes your laundry delicately thanks to
its special turning movements.
• Lingerie
Designed for washing delicate clothes that can only be washed by hand,

15 / EN Washing Machine / User’s Manual
as well as delicate linen. A small number of items should be washed in a net laundry bag.
Hooks, buttons, zippers, etc. must be fastened.
• Piumino (Down Wear)
Use this programme to wash down coats, vests, jackets etc. that bear a “machine-washable” tag.
Thanks to special spin profiles, it is ensured that water reaches the air gaps between feathers.
4.3.7 Special programmes
For specific applications, select any of the following programmes.
• Risciacquo (Rinse)
Use when you want to rinse or starch separately.
• Centrifuga+Scarico (Spin+Drain)
Use this programme to remove the water on the clothes/in the machine.
Before selecting this programme, select the desired spin speed and press Start/Pause button. First,
the machine will drain the water inside of it. Then, it will spin the laundry at the selected spin speed,
and drain the water coming off of the laundry.
If you only want to drain the water without spinning the laundry, select the “Spin+Pump programme,
and use the Spin Speed Adjustment button to select the No Spin function. Press the Start/Pause
button.
C
INFORMATION
• Use a lower spin speed for delicate laundries.
4.3.8 Temperature selecton
Whenever a new programme is selected, the recommended temperature for the selected
programme appears on the temperature indicator.
To decrease the temperature, press the Temperature Adjustment button. Temperature will decrease
gradually. When the cold level is selected, temperature level lights will not be on.
C
INFORMATION
• If the programme has not reached the heating step, you can change the temperature without
switching the machine to Pause mode.
4.3.9 Spn speed selecton
Whenever a new programme is selected, the recommended spin speed of the selected programme
is displayed on the spin speed indicator.
To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases
gradually. Then, depending on the model of the product, "Rinse Hold" and "No Spin" options
appear on the display. When the “No Spin” function is selected, rinse level indicator lights will not
be on.
Rinse hold
If you are not going to unload your clothes immediately after the programme ends, you can use
rinse hold function to keep your laundry in the final rinsing water in order to prevent them from
getting wrinkled when there is no water in the machine. Press Start/Pause button after this process
if you want to drain the water without spinning your laundry. Programme will resume where it left off,
drain the water and then it will be complete.
If you want to spin the laundry held in water, adjust the Spin Speed and press Start/Pause
button. Programme will resume. Water will be drained, laundry will be spun and the programme
will end.

16 / EN Washing Machine / User’s Manual
C
INFORMATION
• If the programme has not reached the spin step, you can change the spin speed without switching the
machine to Pause mode.
4.3.10 Auxlary functon selecton
Select the desired auxiliary functions before starting the programme. You can also select or cancel
auxiliary functions suitable for the running programme without pressing the Start/Pause button while
the machine is operating. To do this, the machine must be in a step before the auxiliary function you
are going to select or cancel. If the auxiliary function cannot be selected or cancelled, light of the
relevant function will flash 3 times to warn the user.
C
INFORMATION
• If a second auxiliary function conflicting with the first one is selected before starting the machine,
the function selected first will be cancelled and the second auxiliary function selection will remain
active.
• An auxiliary function which is not compatible with the programme cannot be selected. (See
"Programme and consumption table")
• Auxiliary Function buttons may vary according to the model of the machine.
4.3.10.1 Auxlary functons
• Prelavaggio (Prewash)
A Prewash is only worthwhile for heavily soiled laundry. Not using the Prewash will save energy,
water, detergent and time.
C
INFORMATION
• Prewash without detergent is recommended for tulle and curtains.
• Rapido (Fast+)
When this function is selected, durations of relevant programmes get shorter by 50%.
Thanks to the optimised washing steps, high mechanic activity and optimum water consumption, high
washing performance is achieved in spite of the reduced duration.
• Pet Hair Removal
This function allows you to remove the pet hair on your garments more efficiently.
If you select this function, Prewash and Extra Rinse programmes will be added to the regular
programme. This way, more water will be used for the washing cycle to ensure that pet hair is
removed more efficiently.
4.3.10.2 Functons/Programmes Selected by Pressng the Functon Buttons for 3 Seconds
• Drum Clean
To select this programme, press and hold the auxiliary function button 1 for 3 seconds.
Use it regularly (every 1-2 months) to clean the drum and ensure the required hygiene is
provided. Run the programme while the machine is totally empty. To obtain better results, put
powder lime-scale remover for washing machines into the detergent compartment no. “2”.
When the programme is over, leave the loading door ajar so that the inside of the machine
gets dry.

17 / EN Washing Machine / User’s Manual
C
INFORMATION
• This is not a washing programme. It is a maintenance programme.
• Do not run this programme when there are any objects in the machine. If you try to do so, the
machine will automatically detect that there is load inside and abort the programme.
• Chld Lock
You can prevent children from tampering with the machine by using the Child Lock feature. Thus you
can avoid any changes in a running programme.
C
INFORMATION
• If the Programme Selection knob is turned when the Child Lock is enabled, "Con" appears on the
display. While the Child Lock is enabled, you cannot make any change in the programmes, the
selected temperature, the speed or the auxiliary functions.
• Even if another programme is selected with the Programme Selection knob while the Child Lock is
enabled, previously selected programme will continue running.
To enable Child Lock:
Press and hold the Auxiliary Function button 2 for 3 seconds. While you’re holding the
button pressed for 3 seconds, C03, C02 and C01 will be displayed respectively.Then, “Con”
will be displayed to warn the user that child lock is enabled.If you press any button or turn
the Programme Selection knob while the Child Lock is enabled, the same warning will be
displayed.
To disable Child Lock:
Press and hold the Auxiliary Function button 2 for 3 seconds while the programme is running. While
you’re holding the button pressed for 3 seconds, C03, C02 and C01 will be displayed respectively.
Then, “COF” will be displayed to warn the user that child lock is disabled.
C
INFORMATION
• In addition to the method above, to deactivate the Child Lock, switch the Programme Selection knob to On/
Off position when no programme is running, and select another programme.
• Child Lock will not be disabled after a power failure or unplugging.
• AntiCrease+
If you press and hold the auxiliary function button 3 for 3 seconds, this function will be selected
and the programme follow-up light of the relevant programme will turn on. When this function
is selected, the drum will rotate for up to eight hours to ensure that the clothes do not crease at
the end of the programme. At any time during these eight hours, you can cancel the programme
and unload the machine. Just press any button or turn the programme selection knob to end the
function. The programme follow-up light will remain on even if you end the function by pressing
any button. If you end the function by turning the programme selection knob, the programme
follow-up light will remain on or go off depending on the selected programme. If you do not cancel
the function by pressing the Auxiliary Function button 3 for 3 seconds, it will be used in the next
washing cycles as well.
4.3.11 End Tme Adjustment
The End Time Adjustment function allows you to set the end time of the programme up to 19
hours. You can increase this time by 1-hour intervals.

18 / EN Washing Machine / User’s Manual
C
INFORMATION
• Please do not use liquid detergent if you have selected the End Time Adjustment function. Stains
might remain on the clothes.
1. Open the loading door, place the laundry and add detergent, etc.
2. Select the washing programme, temperature, spin speed and, if required, the auxiliary functions.
3. Press the End Time Adjustment button and select the desired time.
4. Press the Start/Pause button. The delayed end time you have set will be displayed.
Countdown will start for delayed end. On the display, “_” will move up and down next to the
delayed end time.
C
INFORMATION
• If the programme has not started, you can add laundry into the machine during the delayed end
time.
5. At the end of the countdown, duration of the selected programme will be displayed. “_” will
disappear and the selected programme will start.
Changing the delayed end time
If you want to change the time during countdown: Turn the programme selection knob to cancel
the delayed end time function, and then set the desired time again.
1. Press the End Time Adjustment button. When pressed for the first time, the programme
duration will be rounded up to the closest whole number time. Each following press will
increase the time by an hour.
2. If you want to decrease the delayed end time, press the End Time Adjustment button
consecutively until the desired time is displayed.
Cancelling the delayed end function
If you want to cancel the delayed end time countdown and start the programme immediately:
1. Set the Programme Selection knob to any programme. This way, the Delayed End time will be
cancelled. The End/Cancel light will flash continuously.
2. Then, select the programme you want to run again.
3. Press Start/Pause button to start the programme.
4.3.12 Startng the programme
1. Press Start/Pause button to start the programme.
2. Programme follow-up light showing the startup of the programme will turn on.
C
INFORMATION
• If no programme is started or no key is pressed within 10 minutes during the programme
selection process, the display lights will go off. Once the Programme Selection knob is turned or
any button is pressed, display lights will turn on again.
4.3.13 Progress of programme
Progress of a running programme can be followed from the Programme Follow-up indicator.
At the beginning of each programme step, the relevant indicator light will turn on.
C
INFORMATION
• If the “Anti-crease+”auxiliary function has been selected,“End”LED and “Anti-crease+”LED will be on at
the same time while this step is continuing.
• To end the programme while the“Anti-crease+”step is running, simply press any button or turn the
programme selection knob.
You can change the auxiliary functions, speed and temperature settings without stopping the
programme flow while the programme is running. To do this, the change you are going to
make must be something that will be carried out after the programme step that is running. If

19 / EN Washing Machine / User’s Manual
the change is not suitable, relevant lights will flash 3 times.
C
INFORMATION
• If the machine does not proceed to the spinning step, the Rinse Hold function might be active
or the automatic unbalanced load detection system might be activated due to the unbalanced
distribution of the laundry in the machine.
4.3.14 Loadng door lock
There is a locking system on the loading door of the machine that prevents opening of the
loading door in cases when the water level is unsuitable.
Loading door light will start flashing when the machine is switched to Pause mode. The
machine checks the level of the water inside. If the level is suitable, the loading door light will
turn off and the loading door can be opened within 1-2 minutes.
If the level is unsuitable, the loading door light will remain on and the loading door cannot be opened.
If you are obliged to open the loading door while the Loading Door light is on, you must cancel the
current programme. See "Cancelling the programme"
Opening the loading door in case of power failure:
C
INFORMATION
• In case of a power failure, you can use the loading door emergency handle under the pump filter lid to
manually open the loading door.
A
WARNING!
• Before opening the loading door, make sure that there is no water in the machine to avoid flooding. Water may
be hot and could cause scalding.
• Turn off and unplug the applance.
• Open the pump flter ld.

20 / EN Washing Machine / User’s Manual
• Remove the loadng door emergency handle behnd the flter cover wth a tool.
• Open the loadng door by pullng the loadng door emergency handle downwards.
• Try to pull the handle downwards agan f the loadng door s not opened.
• Brng the loadng door emergency handle to ts orgnal poston after openng the loadng door.
4.3.15 Changng the selectons after programme has started
Switching the machine to pause mode
Press the Start/Pause to switch the machine to pause mode while a programme is running. The
light of the current programme will flash on the Programme Follow-up indicator, indicating that the
machine has switched to pause mode.
Also, when the loading door is ready to be opened, the Loading Door light will turn off in addition to
the programme step light.
Changing the auxiliary function, speed and temperature
Depending on the step the programme has reached, you can cancel or select auxiliary functions. See
“Auxiliary function selection”.
You can also change the speed and temperature settings. See "Spin speed selection" and
"Temperature selection".
C
INFORMATION
• If no change is allowed, the relevant light will flash 3 times.
Adding and removing laundry
1. Press the “Start/Pause” button to pause the machine. The programme follow-up light of
the relevant step during which the machine was switched into the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the loading door and add or take out laundry.
4. Close the loading door.
5. Make changes in auxiliary functions, temperature and speed settings if necessary.
6. Press the “Start/Pause” button to start the machine.
4.3.16 Cancellng the programme
To cancel the programme, turn the Programme Selection knob to select another
programme. Previous programme will be cancelled. End/Cancel light will flash continuously
to notify that the programme has been cancelled.
When you turn the Programme Selection knob, the machine will end the programme but
will not discharge the water inside. When you select and start a new programme, the
newly selected programme will start depending on the step the previous programme was
cancelled in. For example, the machine may take in additional water or continue to wash
with the water inside.
C
INFORMATION
• Depending on the step where the programme was cancelled in, you may have to add detergent
and softener again for the programme you have selected anew.
4.3.17 End of programme
At the end of the programme, “End” will be displayed.
1. Wait until the light of the loading door goes off completely.
2. Switch the programme selection knob to On/Off to switch off the machine.
3. Take out your laundry and close the loading door. Your machine is now ready for the next washing
cycle.
4.3.18 Your machne has the "Pause Mode" functon.
After using the On/Off button to switch on the machine, if you do not start any programme
in the selection step or do not perform anything else, or if you do not do anything in 10