Bell'O FP-4850HG User manual

FP-4850HG Flat Panel Television Stand
A EMBLY IN TRUCTION
Patent Pending
Italian Designed
A Product of China
Do not discard these instructions
-1_051707v3

FOR YOUR SAFETY, PLEASE FOLLOW THESE PRECAUTIONS:
!ALWAYS RE OVE THE TV AND OTHER EQUIP ENT FRO THE FURNITURE PRIOR TO OVING THE ASSE BLED UNIT.
!BE CAREFUL WHEN OVING THE ASSE BLED FURNITURE AFTER THE GLASS SHELVES HAVE BEEN INSTALLED, AS
THIS AY CAUSE THE SHELVES TO BECO E UNSECURED AND FALL.
!WHEN IN USE, THIS FURNITURE UST BE PLACED ON A FLAT, SOLID AND LEVEL SURFACE.
!DO NOT LEAN ON THE TV WHEN IT IS ON THE TV STAND.
!DO NOT CLI B OR STEP ON THE STAND.
!DO NOT BANG INTO OR PLACE YOUR OWN WEIGHT ON ANY GLASS SHELF.
!DO NOT PLACE ITE S ON THE SHELVES WHICH EXCEED THE AXI U WEIGHT LI ITS OF 125 LBS. FOR TELEVISION,
AND 50 LBS. EACH FOR IDDLE AND LOWER GLASS SHELVES
Parts List
Bell’O International Corp. will not be responsible for failure to assemble as directed or for the improper assembly, use or handling of this stand.
NO.
A
B
C
D
E
F
G
H1
1
1
1
1
1
1
1
QTY.
KETCH
I1
NO.
J
1
24
3
4
5
6
7
2
4
4
4
4
2
QTY.
KETCH
7
81
4 mm
60 mm
60 mm
Round
Flat

Assembly Instructions
NOTE: TWO PEOPLE ARE RECO ENDED TO ASSE BLE THIS TABLE.
A. PLACE the Bottom Shelf Frame (C) on the floor upside-down, with the four holes in the frame bottom facing upward. This shelf frame is the
same size as the top shelf frame, but has four holes in the underside of the frame and four holes in each of the rear side bars.
B. CREW the four longer shaft Adjustable Leveling Feet (1) into the Shelf Frame (C) as shown.
Fig. 1
3
Fig. 2A
Fig. 2B
C. PLACE the Flat Panel ounting System Post (A) upright as shown. Working from the rear, PLACE the Right Stabilizing Bracket (D) up
against the rear of the ounting System Post's base as shown in Fig. 2A, and place the Left Stabilizing Bracket (E) up against the rear of
the ounting System Post's base as shown.
D. ECURE the Bottom Shelf Frame (C) to the ounting System Post (A) using four 60mm Bolts (2) as shown in Fig. 2B. Tighten fully using
the supplied Allen wrench.
E. ECURE the Top Shelf Frame (B) to the ounting System Post (A) using four 60mm Bolts (4) as shown in Fig. 2A. Tighten fully using the
supplied Allen wrench. NOTE: The top shelf frame is the same size as the bottom shelf frame, but does not have the four holes in the
bottom of the shelf or four holes in each of the rear side bars.
F. CREW the four Adjustable Feet (3) into the holes located on the bottom of the Left & Right Stabilizing Brackets (D & E) and ensure that
the preassembled unit is level on floor. ove the stand to the location it will occupy when fully assembled and in use.

4
G. PLACE five Glass Pads (7) onto the Bottom Shelf Frame (C). (Place three glass pads along the front, and two
along the rear of the Frame as shown in Fig. 3). PLACE the remaining two Glass Pads on the rear of the Top
Shelf Frame (B).
H. CAREFULLY PLACE the Bottom Glass Shelf (I) onto the Bottom Shelf Frame (C) and LIDE the edge with
the hole through the slot in the C S®panel.
I. CAREFULLY PLACE the Top Glass Shelf (H), onto the top shelf frame (B) and LIDE the edge with the hole
through the slot in the curved C S®panel.
NOTE: Three Adjustable Glass Levelers are preinstalled in the Top Shelf Frame (B). It is important that these are
properly adjusted to support the Top Glass Shelf (H) and to keep it level. TURN each Adjustable Glass Leveler
clockwise or counter-clockwise to adjust. ALWAYS AKE SURE THE TOP GLASS SHELF IS LEVEL BEFORE
PLACING ANY ITE S ON IT.
Fig. 3

5
J. Working from the rear of the assembly, PLACE two plastic T-Pins (6) through the rear holes in the two Glass
Shelves to help prevent the shelves from falling out of place.
K. IN ERT the two C S®(Cable anagement System) Covers (J) into the vertical slots located in the rear of the
Flat Panel ounting System Post (A).You can easily manage and hide the unsightly wires and cables of the TV
and other A/V components by removing these covers, running the cables, then re-attaching the covers.
NOTE: Use the Adjustable Feet (1 and 3) to ensure that the furniture is level on the floor before attempting to
mount the television.
Fig. 4

Mounting the Television
NOTE: TWO PEOPLE ARE RECO ENDED TO OUNT THE TV TO THE STAND
6
L. CHOO E the correct size Flat Panel TV ounting Bars (F or G) that BEST FITS THE SIZE OF YOUR TV. Two sizes of
ounting Bars (27" & 32") have been provided.
. With the screw posts of the Top ounting Bar (F) facing away from the TV, CENTER and ALIGN the ounting Bar with
the upper mounting holes on the rear of your TV. ECURE the Bar to the TV using the screws that were included with
your TV. If you do not have these screws, there is an assortment of common sizes included with this Flat Panel ounting
System. Use a washer and the proper screws as shown in Fig. 5.
N. REPEAT this procedure for the same size Bottom ounting Bar (G). TIGHTEN FULLY BUT DO NOT OVERTIGHTEN.
NOTE: IF THE TV BACK IS NOT FLAT YOU AY HAVE TO USE A LONGER SCREW ALONG WITH THE PACER
THAT ARE ALSO INCLUDED WITH THE HARDWARE.
O. Two Round Nuts (5) have been preinstalled to the two extending bolts in the TOP ounting Bar (F). ake sure they are
only screwed on about half way at this point. This step ensures a safe and easy TV installation later.
P. USING TWO PEOPLE, HOLD the TV with the attached ounting Bars (F or G) up to the assembled Flat Panel ounting
System to the approximate height location where you want the TV to be mounted to determine the desired location of the
Top and Bottom ounting Brackets, which came preinstalled on the Flat Panel ounting System Post (A). If necessary,
adjust the positions of these Brackets using one of the supplied Allen Key Tools.
F
5
Rear of Flat Panel TV
G
Fig. 5

7
Q. USING TWO PEOPLE TO HOLD THE TV, IN ERT the TOP ounting Bar (F) into the desired
keyholes located in the TOP Bracket of the Flat Panel ounting System Post (A) as shown in Fig. 6.
R. IN ERT the extending bolts of the BOTTO ounting Bar (G) in the BOTTO Bracket slots as shown in Fig.
6 and ECURE by tightening all Round Nuts (5) by hand.
F
G
5
5
Fig. 6

Warranty
One (1) Year Limited Warranty
All Bell’O International products are warranted, with the exception of glass, to the original purchaser at the time of
purchase and for a period of one (1) year thereafter. Glass is warranted to the original purchaser at the time of
purchase and for a period of thirty (30) days thereafter. Warranty is only valid in the United States of America.
In order to provide you with timely assistance, please thoroughly inspect your furniture for missing or defective parts
immediately after opening the carton. To receive replacement or missing part(s) under this warranty, go to our
website at www.bello.com or call our Customer Service Department at 1-888-235-7646. Please have the model
number and part number(s) for reference. You will also need your sales receipt or other proof of purchase.
Replacement part(s) will be shipped to you at no charge with Bell’O International assuming all shipping and handling
expense.
We warrant to you, the original purchaser, that our furniture and all of its parts and components are free of defects in
material or workmanship. "Defects", as used in this warranty, is defined as any imperfections that impair the use of
the furniture or product.
Our warranty is expressly limited to the replacement of furniture parts and components. For one (1) year after the
date of purchase, Bell’O International will replace any part described on the enclosed furniture parts list that is
defective in material or workmanship.
This warranty applies under conditions of normal use. Our furniture products are not intended for outdoor use. The
warranty does not cover: 1) defects caused by improper assembly or disassembly; 2) defects caused by shipping,
claims for damage during transit to you should be placed immediately by you to the transportation company;
3) defects occurring after purchase due to product modification, intentional damage, accident, misuse, abuse,
negligence or exposure to the elements; 4) cosmetic damage and 5) labor or assembly costs.
There are no warranties, express or implied, including without limitation merchantability or fitness for particular use,
except as (i) contained herein or (ii) required by applicable law in the state whose law governs (which shall be New
Jersey absent controlling law imposing the law of another state in lieu thereof as governing law). All warranties of
whatsoever derivation shall be limited to the term set forth above, unless otherwise required by applicable law.
Manufacturer’s employees or representatives’ … ORAL OR OTHER WRITTEN STATEMENTS DO NOT CONSTITUTE
WARRANTIES, shall not be relied upon by Buyer, and are not a part of the contract for sale or this limited warranty.
Except as provided herein, Bell’O International shall have no liability or responsibility to the purchaser or any other
person or entity with respect to any liability, loss or damage caused directly or indirectly by use of the product,
including, but not limited to, any incidental or consequential damages. Some states do not allow limitation on how
long an implied warranty can last or the exclusion of limitation of incidental or consequential damages, so the above
limitation and exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights, which vary from state to state.
BELL'O INTERNATIONAL CORPORATION, 711 Ginesi Drive, Morganville, NJ 07751-1235
Table of contents
Other Bell'O Rack & Stand manuals
Popular Rack & Stand manuals by other brands

Mount-It!
Mount-It! MI-2757 installation manual

Techly
Techly ICA-LCD 482-T Installation instruction

Middle Atlantic Products
Middle Atlantic Products WMRK Series instruction sheet

Burlington
Burlington T21A CHR manual

ENERMAX
ENERMAX EMK3105PCI user manual

ShelterLogic
ShelterLogic RACK-IN-A-BOX 90365EU manual