CommScope NETpodium 1-1671405-1 User manual

NETpodium Rack (1-1671405-1 & 1-1671405-2)
INSTRUCTION SHEET 411-117000 Jan 2017 Rev B
1-1671405-1
1. Kit Content
Bottom Frame Assembly 1 pc
Top Frame Assembly 1 pc
Carboard Stencil 1 pc
Vertical Profile Assembly 6 pc
Wire Basket 2 pcs
Bracket Wire Baskets 8 pcs
15U Cable Managers 6 pcs
(only for 1-1671405-1)
Mounting Hardware
1-1671405-2

2.3. Mounting a bracket or accessory with Tool-less
Fastener (TF)
- Insert the TF into the T-Channel
- Quarter turn clockwise
- TF is ASSEMBLED in the T-Channel, you can
still slide it to choose it’s position
2. Prefix: Installing the brackets with screws and
Tool-less Fastener (TF)
2.1. The profile
2.2. Mounting a bracket or accessory with screws & washers
- Insert the bracket or accessory into the groove
- Line-up the hole(s)
•
•
- Assemble screw and washer in the T-channel
Use an Allan key n°5 with conical head
Bracket needs to be fixed with a torque of 3.5-4Nm
T-Channel
Groove
NETpodium Rack
INSTRUCTION SHEET
2

B
•
•
•
- Insert the accessory or bracket
- Line-up the holes
- Slide the fastener if necessary
- Push
- Fixation OK
TWO WAYS TO USE IT (A or B)
A
- Push
- TF is FIXED , you can NOT slide it
- A bracket or accessory can be slid with the slotted hole
over the fastener pin into the groove
NETpodium Rack
INSTRUCTION SHEET
3

3. Assembly instruction
3.1. Mount the frame to the floor
- Use the enclosed stencil to indicate the mounting
positions on the floor, use the holes with references
A,B,C and D.
- Anchor the bottom frame to the floor.
2.4. Removing a bracket or accessory with Tool-less
Fastener (TF)
- Pull to release the accessory or bracket
The previous step can also be done using a small,
flat head screwdriver:
- Insert the screwdriver under the head of the TF and turn
90° counterclockwise to release.
- Accessory or bracket can be removed, TF is still
assembled in T-Channel
- Quarter turn counter clockwise, to release TF
- Remove TF
BACK
FRONT
C
A
A B
C D C’
908 mm
530 mm
994 mm
POSITIONS MOUNTING HOLES ON THE FLOOR
A’ B’
D’
PULL
PULL
2x
NETpodium Rack
INSTRUCTION SHEET
4

- The result.
- Slide the Stencil towards the top.
- Assemble one TF on two Vertical Profiles to prevent the
stencil from dropping down (position fastener: 3 holes
from the top of the Vertical Profile) (See paragraph 2.3).
3.2. Assemble the profiles
- Put the stencil on top of the bottom frame.
- Assemble all the Vertical Profiles.
To position the vertical profiles look at the pictures on
the stencil. Pay attention to the brackets assembled on
the profiles.
- Fix the screws with washers with a torque of 3.5-4Nm.
(See Paragraph 2.2.).
TOP
NETpodium Rack
INSTRUCTION SHEET
5

- ATTENTION: Fix the brackets in the corner of the Top
Frame assembly on the Vertical profiles.
- Remove the TF's (See paragraph 2.4) and slide the
stencil back downwards.
- Fix all screws of the bottom frame assembly properly
(a torque of 3.5-4Nm).
- The result.
- Assemble the Top Frame on the Vertical profiles.
- Loosen the TF's and lower the stencil a little bit.
Fix all screws of the top frame assembly properly
(a torque of 3.5-4Nm).
NETpodium Rack
INSTRUCTION SHEET
6

- To mount the 4 wire basket brackets on the bottom side:
1. First mount a TF in
the channel (position
indicated on stencil)
and fix it in the 6th available
hole above the screw
on the bottom side of the
(See paragraph 2.3).
2. Assemble the
wire basket bracket
in the groove and
position it on the TF.
3. Mount the second
TF in the channel,
in the third hole
beneath the first
TF and fix it. (See
paragraph 2.3.)
- Repeat this for the 4 wire basket brackets mounted on
the bottom side of the profiles. See positions indicated
on the stencil.
3.3. Assemble the wire baskets
- The TF's for the brackets for the Wire Baskets have to be
assembled in the 4 profile channels indicated on the stencil.
– In each corresponding groove, 2 brackets have to be
assembled. One on the top side and one on the bottom
side of the groove.
- To mount the 4 wire basket brackets on the top side:
1. First mount a TF in the
channel (position indicated
on the stencil) and fix it
in the 3rd available hole
beneath the screw on the
top side of the profile.
(See paragraph 2.3).
2. Assemble the wire
basket bracket in the
groove and position it on
the TF.
3. Mount the second TF in
the channel, in the third hole
beneath the first TF and fix
it. (See paragraph 2.3.)
Repeat this for the 4 wire
basket brackets mounted
on the top side of the
profiles. See positions
indicated on the stencil.
NETpodium Rack
INSTRUCTION SHEET
7

- To fix each wire basket
use only ONE screw and
washer per wire basket.
- To ground each wire
basket use only ONE screw
and washer per wire basket.
3.4. Assemble the cable managers (15U)
- Insert the bracket with
cable managers 15U into
the groove and fix it with
TF’s. (See paragraph
2.3.)
- The position of the TF is indicated with a small cut on
the top and bottom of the metal bracket.
- Tear the stencil apart, use the holes indicated by PULL.
You don’t need it anymore.
- Hang the wire baskets with the shortest side in the
brackets towards the back.
- Position it at the same time on the second horizontal
wire from the top and bottom, see picture.
- Then rotate the wire baskets inwards and hang them in
the brackets towards the front side.
Shortest side
NETpodium Rack
INSTRUCTION SHEET
8

- To ground the bracket mount the screw. The position
is indicated with two small cuts in the middle of the
metal bracket.
3.5. How to remove a cable manager
- Insert the screwdriver in the small cutout and turn 90° to
release. Reapet this in the 4 cutouts of the the cable manager.
- Use two screwdrivers to release the snap hooks on the
reverse of the metal bracket.
- Push to remove the cable manager.
- Cable manager is removed.
4. Troubleshooting
- If it is not possible to assemble screw and washer while
mounting a bracket:
Loosen the already assembled screws of the bracket.
Move the bracket a little bit to align the holes properly.
Fix all screws with a torque of 3.5-4Nm.
INSTRUCTION SHEET
Contact us:
Technical Support
Technical Assistance Center (TAC)
Greensboro, North Carolina
www.commscope.com/SupportCenter/TechnicalSupport.aspx
Tel: [phone]
Email: [e-mail]
www.commscope.com
This product is covered by one or more U.S. patents or their foreign equilvalents. For patents, see www.commscope/ProductPatent/ProductPatent.aspx
©2017 CommScope, Inc.
All Rights Reserved.
NETpodium Rack
INSTRUCTION SHEET
To obtain more information on CommScope® products visit our website at www.commscope.com/supportcenter/TechnicalSupport.aspx