Bellini CGH9501 User manual

Bellini – 60/90cm gas hob
Installation and Operating Instructions
Contents Page
1. INTRODUCTION AND SAFETY WARNINGS 1
2. OPERATING INSTRUCTIONS 2
3. CLEANING INSTRUCTIONS 3
4. TROUBLESHOOTING 4
5. INSTALLATION 5
6. SERVICING and PARTS 10
7. WARRANTY 10

Bellini – 60/90cm gas hob
Rev: 8-9-2010 1
1. INTRODUCTION AND SAFETY WARNINGS
Congratulations on your investment in Bellini, quality stainless steel gas hotplates.
Please carefully read the following installation and operating instructions to ensure you get the
safest operation from this appliance.
These instructions apply only to the models CGH9501 and BG905X – 5 burner models and the
CGH6401 and BG604X – 4 burner models, for use with Natural Gas or Universal LPG.
NOTE: Refer to gas type label and data plate label to ensure appliance is setup for the correct
gas type. If in doubt, refer to gas supplier.
WARNINGS:
oDo not use or store flammable materials in the appliance storage
drawer or near this appliance.
oDo not spray aerosols in the vicinity of this appliance while it is in
operation.
oDo not modify this appliance.
oFor Universal LPG appliance:- Where this appliance is installed in
marine craft or caravans, it shall not be used as a space heater.
oDisconnect electricity supply to the appliance before any servicing
work is conducted.
oThis appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
oChildren should be supervised to ensure that they do not play with the
appliance.
oThe appliance electrical supply must allow for disconnection after the
installation of the appliance.
oCord type Y – If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
For future reference please store these instructions in a safe place.

Bellini – 60/90cm gas hob
Rev: 8-9-2010 2
2. OPERATING INSTRUCTIONS
LIGHTING THE BURNER
The hotplates are fitted with mains powered electronic spark ignitors, so must be connected to
mains power supply (i.e. nominal 230 V ac) to operate. If power is not available, the hotplate
will still work but the burners will have to be lit with a match or similar.
Depressing the gas control knob of any burner will activate the spark ignition for all burners.
To light the burner, turn the gas control knob to the High Flame setting of the burner to be lit,
while at the same time depressing the gas control knob to activate the spark ignition.
Once the burner is alight continue to depress the gas control knob for 5 – 10 seconds to allow
the flame safeguard to activate. If when you release the gas control knob, the burner flame
goes out the flame safeguard has not heated up enough so repeat the ignition procedure after
waiting 1 minute for gas to disperse. If problems with burner lighting persist, refer to the
TROUBLESHOOTING section of these instructions.
If power is not available, light a match or similar, then turn the gas control knob for the
burner to be lit, to the High Flame setting. Once again if problems with burner lighting persist,
refer to the TROUBLESHOOTING section of these instructions.
When burner lights, adjust desired flame height. On finishing, turn control knob to off position
marked with a black DOT.
BURNER AND UTENSIL CHOICE
Depending on the hotplate model, the burner choices are:
Model CGH6401: Auxiliary (small), Semi-Rapid (medium), and Rapid (large) burners.
Models CGH9501 and BG905X: Auxiliary (small), Semi-Rapid (medium), Rapid (large), and
Triple ring (wok) burners.
Model BG604X: Auxiliary (small), Semi-Rapid (medium), and Triple ring (wok) burners.
The maximum utensil (pan) diameters in millimetres (mm) for each burner are:
1. For Natural Gas hotplates
•Auxiliary (small) and Semi-Rapid (medium) = 195 mm
•Rapid (large) = 230 mm
•Triple ring (wok) = 270 mm
2. For Universal LPG hotplates
•Auxiliary (small), Semi-Rapid (medium) and Rapid (large) = 195 mm
•Triple ring (wok) = 230 mm
The minimum utensil (pan) diameters in millimetres (mm) for each burner are:
•Auxiliary (small) = 80 mm
•and Semi-Rapid (medium) = 140 mm
•Rapid (large) and Triple ring (wok) = 195 mm
For best efficiency and to ensure utensil handle does not overheat, place the utensil centrally
on the burner and adjust the flame height so all the flame remains under the utensil.

Bellini – 60/90cm gas hob
Rev: 8-9-2010 3
3. CLEANING INSTRUCTIONS
GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially when
cleaning the enameled parts.
Avoid leaving alkaline or acid substances(lemon juice, vinegar etc.) on the surfaces.
STAINLESS STEEL
The stainless steel hob of the hotplate must be cleaned regularly (e.g. weekly) to ensure long
life expectancy of the hotplate.
Ensure hotplate has cooled. Wash down with warm soapy water and rinse with clean water.
Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.
NOTE: Ensure that wiping is done along with the grain of the stainless steel to prevent any
unsightly crisscross scratching patterns from appearing.
TRIVETS (UTENSIL SUPPORTS)
Enameled parts must only be washed with a sponge and soapy water or with non-abrasive
products. Rinse with clean water. Dry with a clean soft cloth.
BURNERS
Remove trivets from hob. Ensure burners are cool.
Remove the burners enameled cap (C) and aluminium
burner crown (F).
Wash down with warm soapy water and rinse with clean
water. Dry with a clean soft cloth.
Replace burners and ensure they are correctly re-
positioned over the ignitor (S) and thermocouple (T). The
ignitor (S) must be clean for trouble free sparking. Test
burner ignition and burner flame for correct operation.
The Triple Ring (Wok) burner (diagrams below) does not
fit over the ignitor or thermocouple but must be placed
on its supports. If burner is placed correctly it will not
rotate on its supports.
Refer to diagrams below.

Bellini – 60/90cm gas hob
Rev: 8-9-2010 4
4. TROUBLESHOOTING
Servicing of the hotplates must only be done by an authorised service representative (see
back of this booklet) and the hotplate must not be modified. Power must be disconnected
before any servicing or maintenance is conducted.
Abnormal conditions include : Excessively yellow or sooting flame type.
: Flame lifting off the burner ports.
: Flame lighting back into the burner (normally associated with a
popping sound).
: Objectionable odour of the flames combustion products.
Should a faulty condition develop in the hotplate that is not described above, refer to the
following table first for possible causes and remedies prior to contacting an authorised service
representative. Servicing beyond the remedies listed shall only be undertaken by an
authorised service representative.
TROUBLESHOOTING TABLE
FAULT POSSIBLE CAUSE REMEDY
No spark when gas control knob
depressed. No power.
Check plugged in and switched
on. Check mains circuit breaker.
Loose sparker cable. Call authorised representative.
Burner not aligned properly. Remove and re-fit burner.
Burner not lighting when spark
ignition working. Gas supply off. Check gas supply valve on.
Burner not aligned properly. Remove and re-fit burner.
Burner ports blocked. Remove, clean and replace burner.
Burner goes out when control
knob released. Flame safeguard not activated. Re-light, allow more time for flame safeguard to activate.
Flame safeguard faulty connection or broken. Call authorised representative.
Uneven flame pattern or slight
flame lifting. Burner ports blocked. Remove, clean and replace burner.
At minimum flame setting the
flame is too high. Turndown control setting incorrect. Call authorised representative.
Small flame on High setting. Regulator faulty. Call authorised representative.
Gas supply pressure low. Call authorised representative.
Incorrect injector fitted. Call authorised representative.
Blocked injector or gas supply tube. Call authorised representative.
Incorrect utensil size. Refer to operating instructions - utensil choice.
Flame too high on High setting. Regulator faulty. Call authorised representative.
Incorrect injector fitted. Call authorised representative.
Incorrect utensil size. Refer to operating instructions - utensil choice.

Bellini – 60/90cm gas hob
Rev: 8-9-2010 5
5. INSTALLATION
IMPORTANT NOTE: Refer to the Warnings in Section 1 of these Instructions.
This hotplate must be installed in accordance with:
•AS 5601 - Gas Installations (for Australia)
•NZS 5261 – Code of Practice for the Installation of Gas Burning Appliances
and Equipment (for New Zealand)
•Local gas fitting regulations
•AS/NZS 3000 – Electrical Installations (Wiring Rules)
•Building codes
•Any other relevant statutory regulations.
Check the gas type label on the underside of the hotplate, adjacent to the gas connection to
ensure it corresponds to the installation gas supply. If in doubt contact the supply authority.
NOTE: Before cutting into any bench tops, ensure the minimum clearances to walls, adjacent
surfaces and overhead surfaces required by the relevant gas appliance installation
code (see above) will comply. Dimensions are specified in millimetres (mm)
MINIMUM CLEARANCES:
•Overhead cupboards and range hood = 600 mm.
•Side and rear clearance = 200 mm to any burner edge.
•Overhead exhaust/ceiling fan = 750 mm
•Horizontal surfaces adjacent the hob = less than or equal to the hob height.
•Ensure there is sufficient clearance to fit the regulator and/or flexible hose
connection with the hotplate in the installed position.
GAS and ELECTRICAL CONNECTION LOCATIONS and OVERALL DIMENSIONS:
Model CGH6401: Bench cutout size, 555 mm wide x 473 mm deep.
Bench top thickness, 30 – 40 mm (3 – 4 cm).

Bellini – 60/90cm gas hob
Rev: 8-9-2010 6
Model CGH9501: Bench cutout size, 830 mm wide x 473 mm deep.
Bench top thickness, 30 – 40 mm (3 – 4 cm).
Model BG604X: Bench cutout size, 555 mm wide x 473 mm deep.
Bench top thickness, 30 – 40 mm (3 – 4 cm).

Bellini – 60/90cm gas hob
Rev: 8-9-2010 7
Model BG905X: Bench cutout size, 830 mm wide x 472 mm deep.
Bench top thickness, 30 – 40 mm (3 – 4 cm).
Once satisfied that minimum clearances to
combustible can be achieved, cut out the bench
top to the dimensions specified.
Apply the adhesive sealing tape to the
underside lip of the burner box. Shown at G
opposite.
Place burner box into cutout hole and fit
clamping brackets to clamp the hotplate to the
bench.
See two clamping method diagrams below:

Bellini – 60/90cm gas hob
Rev: 8-9-2010 8
Then a particle board or similar heat
baffle must be installed under the hob
to prevent accidental touching of the
underside surface.
Leave sufficient rear clearance to
access gas and electrical connections.
ELECTRICAL CONNECTION:
Install a 10 amp general purpose
outlet (GPO) in accordance with
relevant electrical standards and/or
codes of practice applicable.
The power supply cord (supplied) must
not touch against any hot surfaces and
must be placed so that its temperature
does not exceed 75oC at any point
along its length.
After having installed the hotplate, the
GPO must always be in an accessible
position.
GAS CONNECTION:
Install in accordance with relevant gas standards and/or codes of
practice applicable.
Connect the elbow fitting to the appliance gas manifold connection.
For Natural gas: connect the natural gas appliance regulator
(pictured opposite) with integral test point using approved gas
thread tape or compound to the elbow fitting.
For Universal LPG: connect the brass test point adaptor (pictured
opposite) using approved gas thread tape or compound to the
elbow fitting.
Ensure the supply connection point, test point and natural gas
regulator adjustment screw (for Natural gas installation) are
accessible for testing and/or adjustment with the hotplate in the
installed position.
Where a flexible hose assembly is used, ensure it is approved to
AS/NZS 1869, Class B. Any hose assembly used must be restrained
from accidental contact with the flue outlet of an under bench oven.
After connecting to gas, check for leaks using soapy solution, never a naked flame.
Fit the duplicate data plate (supplied in separate bag) on a surface adjacent to the hotplate,
for example, the inside of the cupboard door so it is clearly visible for any service technician.
SETTING THE GAS PRESSURE:
Fit a manometer with a 6 mm rubber hose to the test point on the regulator (for natural gas).
For the Model CGH6401, light one Rapid and Auxiliary burner and adjust test point pressure
to 1.00 kPa. Turn the two burners off and on again and recheck the pressure is same as set
previously or adjust as required.
Brass test point adaptor
Natural Gas Regulator

Bellini – 60/90cm gas hob
Rev: 8-9-2010 9
For the Models CGH9501, BG604X and BG905X, light the Triple Ring and Auxiliary burner
and adjust test point pressure to 1.00 kPa. Turn the two burners off and on again and recheck
the pressure is same as set previously or adjust as required.
TEST FOR CORRECT OPERATION:
After installation and test point setting, each burner ignition and operation must be tested
individually and with all burners operating.
This testing must be done by the installer before leaving.
ADJUSTING THE BURNER MINIMUM FLAME HEIGHT:
NOTE: This adjustment can only be performed by authorised service personnel.
The minimum burner flame is factory adjusted for the gas type stated on the gas type label
adjacent to the gas connection and should not require adjustment.
Adjustment may be required if the hotplate has been converted from Natural gas to Universal
LPG or vice versa.
GAS CONVERSION INSTRUCTIONS:
The manufacturers servicing instructions detail how authorised personnel may convert the
hotplate from Natural gas to Universal LPG or from Universal LPG to Natural gas.
Contact the manufacturer or agent as required.
NATURAL GAS UNIVERSAL LPG
Model CGH6401 Inj Diam MJ/h Test point kPa Inj Diam MJ/h Test point kPa
Auxiliary 0.90 4.0 1.00 0.55 4.0 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Rapid 1.35 10.0 1.00 0.90 11.0 2.75
TOTAL NHGC 26.0 MJ/h 27.8 MJ/h
NATURAL GAS UNIVERSAL LPG
Model CGH9501 Inj Diam MJ/h Test point kPa Inj Diam MJ/h Test point kPa
Auxiliary 0.90 4.0 1.00 0.55 4.0 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Rapid 1.35 10.0 1.00 0.90 11.0 2.75
Triple ring 1.70 14.0 1.00 0.98 12.5 2.75
TOTAL NHGC 40.0 MJ/h 40.3 MJ/h
NATURAL GAS UNIVERSAL LPG
Model BG604X Inj Diam MJ/h Test point kPa Inj Diam MJ/h Test point kPa
Auxiliary 0.90 4.0 1.00 0.55 4.0 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Triple ring 1.70 14.0 1.00 0.98 12.5 2.75
TOTAL NHGC 30.0 MJ/h 29.3 MJ/h
NATURAL GAS UNIVERSAL LPG
Model BG905X Inj Diam MJ/h Test point kPa Inj Diam MJ/h Test point kPa
Auxiliary 0.90 4.0 1.00 0.55 4.0 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Semi rapid 1.10 6.0 1.00 0.70 6.4 2.75
Rapid 1.35 10.0 1.00 0.90 11.0 2.75
Triple ring 1.70 14.0 1.00 0.98 12.5 2.75
TOTAL NHGC 40.0 MJ/h 40.3 MJ/h

Bellini – 60/90cm gas hob
Rev: 8-9-2010 10
6. SERVICING AND PARTS
A maintenance schedule for the life expectancy of the hotplate only comprises a complete
clean of the Hob, Trivets and Burners as detailed in the Cleaning Instructions on an annual
basis. Maintenance of the gas valve and flame safeguard system components are not required.
Should the hotplate appear to be operating abnormally, contact the Authorised Dealer to
arrange for servicing and/or repair.
Note: Servicing shall only be carried out by authorised personnel.
To arrange for any spare or replacement parts and servicing, contact:
Authorised Dealer, phone: [phone]
7. WARRANTY
The benefits conferred by this warranty are in addition to all implied warranties, other rights
and remedies in respect of the product which the consumer has under the Trade Practices Act
and similar State and Territory Laws.
The original purchaser of this Bellini product is provided with the following warranty, subject to
the following warranty conditions.
This product is warranted for a period of 2 years from the date of purchase for all parts
defective in workmanship or materials. Should an instance occur where the product is deemed
faulty, the product will need to be returned to the retailer where it was purchased to be
replaced free of charge or a refund issued. In order to obtain an exchange or a refund, proof
of purchase must be presented to the retailer.
WARRANTY CONDITIONS
1. This warranty is only valid for appliances installed and used according to the manufacturer’s
instructions.
2. This warranty does not apply to damage caused if your appliance has been dismantled,
repaired or serviced by any person other than someone authorised by the Company.
3. If you live outside the service area of the Company or one of its service agents, this
warranty does not cover the cost of transport of the appliance for service nor the service
agent’s travelling costs to and from your home.
4. If you are required to transport the appliance to the Company or its service agent, you
must ensure it is securely packed and insured. The Company does not accept any
responsibility for loss or damage of the appliance prior to it being received by the Company
or its service agent.
5. This warranty does not cover loss, damage or expense to this appliance caused directly or
indirectly by power surges, electrical storm damage or connected to incorrect power supply.
6. The Company (and any company related to the Company) will not be liable for any special,
incidental or consequential damages or for loss, damage or expense or for personal injury or
loss or destruction of property arising directly or indirectly from the use or inability to use
this appliance or any of its parts.
7. Warranty will only be given where proof of purchase is provided, e.g. original invoice.
8. Not designed or warranted for industrial or commercial use (Commercial use applies to
shops, offices, schools, factories & workshops etc.).
DO NOT SEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice.

Bellini – 60/90cm gas hob
Rev: 8-9-2010 11
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. You must be able to present it at
the place of purchase to obtain a replacement or a refund.
GSM Sales Pty Ltd reserves the right to discontinue items, modify designs and change
specifications without incurring obligation.
Whilst every effort is made to ensure that descriptions, specifications and other information in
this publication is correct, no warranty is given in respect thereof and the company shall not
be liable for any errors therein.
NOTES:
Cat. No. CGH6401, CGH9501, BG604X, BG905X.