Kogan KAWLM70CNRA User manual

TILT EXTENDABLE FULL MOTION
CORNER WALL MOUNT
(32" - 70")
KAWLM70CNRA

•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and quality tools must be used.
•This product is suitable for installation on solid concrete walls, masonry walls or
wood stud walls.
•Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
•Use the mounting screws provided and DO NOT OVER TIGHTEN mounting
screws.
•Do not allow children to play near this stand.
•This product contains small items that could be a choking hazard if swallowed.
Keep these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead
to product failure and personal injury.
•A minimum of two people are recommended for this installation. Failure to use
safety gear and safe working methods may result in property damage, serious
injury or death.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
VESA compatibility:
75x75, 100x100, 100x150, 100x200, 150x100, 150x150, 200x100, 200x200,
300x200, 300x300, 400x200, 400x300, 400x400, 600x400
CAUTION:
Rated weight is 45kg (99 lbs).
Use with products heavier than the rated weights indicated may result
in instability causing possible injury.
Suitable for TVs 32” – 70” maximum
SAFETY & WARNINGS

Wall mount assembly:
A(x1)
B(x2)
C(x1)
W-A ST6.3x55 (x8)
W-B 10x45 (x8)
W-C (x8)
Adapters (depends on TV):
M-A M5x14 (x4)
M-B M6x14
(x4)
M-C M6x30 (x4) M-D M8x30 (x4)
M-E M8x50 (x4)
M-F (x4)
M-G (x8)
M-H (x8)
Additional Tools Required (Not Supplied):
Phllips head
screwdriver
Stud finder
Spirit level
Pencil
Electric drill
Socket wrench
COMPONENTS

Step 1: Drywall, plaster or timber walls (with studs)
Use a stud finder to locate safe and suitable locations to install into wall. Use a spirit level to
double check the correct angle of the mount and mark the intended hole positions with a
pencil. Drill holes in the desired locations (55mm deep, 4.5mm wide).
With the wall mount held in place, insert the washers and screws (W-C, W-A), tightening
with a socket wrench. When installing on a drywall, plaster or timber wall, do not use the
screw anchors (W-B).
Ensure washers and screws are aligned in the
centre of opening. Do not install with washers and
screws off to either side.
ASSEMBLY

Step 1: Concrete and masonry walls
Use a spirit level to double check the correct angle of the mount and mark the intended hole
positions with a pencil. Drill holes in the desired locations (60mm deep, 10mm wide).
Insert the screw anchors (W-B) into each pre-drilled hole. With the wall mount held in place,
insert the washers and screws (W-C, W-A), tightening with a socket wrench.
For all wall types:
Ensure washers and screws are aligned in the
centre of opening. Do not install with washers and
screws off to either side.
A minimum of two people are recommended for this installation.
Failure to use safety gear and safe working methods may result in
property damage, serious injury, or death.

Step 2: Attaching the mounting brackets to your TV.
Depending on your TV, a combination of spacers (M-G, M-H) may be required to help create
the correct amount of space for the brackets. Ensure the screws are fitted correctly into your
TV’s VESA mount holes, and are not too long or too short in the back of the TV.

Step 3: Attaching the TV to the wall mount.
With two people, lift the TV up and above the installed wall mount and gently lower down
into place (3a), ensuring the TV is positioned evenly in the middle of the mount.
The brackets each feature a vertical screw to secure to the bottom of the mount. Hook this
screw underneath the mount (3b), and tighten to secure.
A minimum of two people are recommended for this installation.
Failure to use safety gear and safe working methods may result in
property damage, serious injury, or death.

Step 4: Use the supplied cable management clips to secure all of the TV’s power and
connection cables, as shown below.

Note:
Adjust to the desired angle then tighten the screws using the tool as shown,
alternating from each screw as you tighten them.
ADJUSTING

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com